Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2016.01
RM3250E _57 Power Source / Network _038063 NETWORKING _0186537 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU) (w/ Seat Heater System)

·

Steering lock actuator or upper bracket assembly

·

Harness or connector



WIRING DIAGRAM

B301186E07
0.594,1.406 2.719,1.823 2.125,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.604,1.219 1.063,1.417 0.458,0.198 10 false G69 1.854,0.75 2.313,0.948 0.458,0.198 10 false LIN 2.146,0.583 2.458,0.781 0.313,0.198 10 false 5 5.094,0.74 5.708,0.938 0.615,0.198 10 false LIN1 4.906,0.594 5.063,0.792 0.156,0.198 10 false 2 4.75,1.198 5.208,1.396 0.458,0.198 10 false G82 4.76,1.385 6.302,1.74 1.542,0.354 10 false ID Code Box (Immobiliser Code ECU)* 4.927,2.292 5.083,2.49 0.156,0.198 10 false 5 5.104,2.427 5.563,2.625 0.458,0.198 10 false LIN 4.479,2.865 4.792,3.063 0.313,0.198 10 false G71 4.479,3.042 6.635,3.417 2.156,0.375 10 false Steering Lock Actuator or Upper Bracket Assembly 0.698,3.427 2.594,3.656 1.896,0.229 10 false : LIN Communication Line 0.302,3.083 2.198,3.313 1.896,0.229 10 false *: w/ Seat Heater System

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

If the certification ECU (smart key ECU assembly) or steering lock actuator or upper bracket assembly is replaced, refer to the Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

w/ Seat Heater System:

Disconnect the G82 ID code box (immobiliser code ECU) connector.


c.

Disconnect the G71 steering lock actuator or upper bracket assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-5 (LIN) - G71-5 (LIN) Always Below 1 Ω
G69-5 (LIN) - G82-2 (LIN1) Always Below 1 Ω
G69-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Disconnect the G71 steering lock actuator or upper bracket assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output (w/o Seat Heater System)
DTC B2785 is output (w/ Seat Heater System)



DTC B2785 is not output

6.REPLACE STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY

DTC B2785 is output (w/o Seat Heater System)

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

DTC B2785 is output (w/ Seat Heater System)

8.CLEAR DTC
6.REPLACE STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY
a.

Replace the steering lock actuator or upper bracket assembly with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CLEAR DTC
a.

Disconnect the G82 ID code box (immobiliser code ECU) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

10.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (ID CODE BOX [IMMOBILISER CODE ECU] IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)