Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Radio and Display Type)
RM3250E _56 Audio / Visual / Telematics _038054 PARK ASSIST / MONITORING _0186539 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM

E316631E02
5.781,0.99 6.24,1.188 0.458,0.198 10 false CA+ 5.792,1.448 6.25,1.646 0.458,0.198 10 false V+ 5.792,1.938 6.25,2.135 0.458,0.198 10 false V- 5.792,2.365 6.25,2.563 0.458,0.198 10 false CGND 5.458,0.885 5.917,1.083 0.458,0.198 10 false 11 5.458,1.344 5.917,1.542 0.458,0.198 10 false 12 5.458,1.833 5.917,2.031 0.458,0.198 10 false 24 5.458,2.25 5.917,2.448 0.458,0.198 10 false 23 4.563,2.552 5.229,2.75 0.667,0.198 10 false Shielded 3.75,2.552 4.417,2.75 0.667,0.198 10 false Shielded 2.885,2.552 3.552,2.75 0.667,0.198 10 false Shielded 2.063,2.552 2.729,2.75 0.667,0.198 10 false Shielded 1.583,0.885 2.042,1.083 0.458,0.198 10 false 6 1.583,1.344 2.042,1.542 0.458,0.198 10 false 3 1.594,1.833 2.052,2.031 0.458,0.198 10 false 2 1.604,2.26 2.063,2.458 0.458,0.198 10 false 5 1.115,0.969 1.573,1.167 0.458,0.198 10 false CB+ 1.104,1.417 1.563,1.615 0.458,0.198 10 false CV+ 1.125,1.917 1.583,2.115 0.458,0.198 10 false CV- 0.99,2.365 1.448,2.563 0.458,0.198 10 false CGND 5.365,2.813 5.823,3.01 0.458,0.198 10 false G38 5.396,2.969 7.125,3.292 1.729,0.323 10 false Radio and Display Receiver Assembly 0.24,2.802 0.698,3 0.458,0.198 10 false P2 0.25,2.969 1.719,3.354 1.469,0.385 10 false Rear Television Camera Assembly

CAUTION / NOTICE / HINT

HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Service.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G38 radio and display receiver assembly connector.


b.

Disconnect the P2 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-11 (CA+) - P2-6 (CB+) Always Below 1 Ω
G38-12 (V+) - P2-3 (CV+) Always Below 1 Ω
G38-23 (CGND) - P2-5 (CGND) Always Below 1 Ω
G38-24 (V-) - P2-2 (CV-) Always Below 1 Ω
G38-11 (CA+) or P2-6 (CB+) - Body ground Always 10 kΩ or higher
G38-12 (V+) or P2-3 (CV+) - Body ground Always 10 kΩ or higher
G38-23 (CGND) or P2-5 (CGND) - Body ground Always 10 kΩ or higher
G38-24 (V-) or P2-2 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E315712C06
1.469,0.219 1.969,0.469 0.5,0.25 0.688,0.385 0.969,0.385 0.969,0.385 1.208,1.021 true 0.844,1.865 1.125,1.865 1.125,1.865 1.208,1.302 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 0.396,0.302 0.792,0.49 0.396,0.188 10 false CA+ 1.594,0.26 1.906,0.458 0.313,0.198 10 false G38 0.438,1.792 0.969,2.01 0.531,0.219 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G38-11 (CA+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL

E315713C04
1.417,0.542 1.917,0.792 0.5,0.25 3.938,2.333 3.688,2.333 3.688,2.333 3.594,1.74 true 3.073,2.333 3.323,2.333 3.323,2.333 3.5,1.802 true 6.156,2.333 5.906,2.333 5.906,2.333 5.76,1.635 true 5.24,2.333 5.49,2.333 5.49,2.333 5.646,1.688 true 0.698,2.135 0.948,2.135 0.948,2.135 1.125,1.604 true 0.5,1.396 0.969,1.396 true 0.667,0.417 0.979,0.615 0.313,0.198 10 false *a 1.531,0.583 1.99,0.802 0.458,0.219 10 false G38 2.833,1.344 3.292,1.563 0.458,0.219 10 false GND 4.979,1.344 5.438,1.563 0.458,0.219 10 false GND 2.906,2.25 3.365,2.469 0.458,0.219 10 false *d 3,0.417 3.458,0.635 0.458,0.219 10 false *b 5.167,0.417 5.625,0.635 0.458,0.219 10 false *c 0.302,1.313 0.76,1.531 0.458,0.219 10 false V+ 0.302,2.052 0.792,2.271 0.49,0.219 10 false CGND 3.969,2.24 4.427,2.458 0.458,0.219 10 false *e 5.083,2.25 5.542,2.469 0.458,0.219 10 false *d 6.198,2.229 6.656,2.448 0.458,0.219 10 false *e
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:
·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

·

The video waveform changes according to the image sent by the rear television camera assembly.



Item Content
Terminal No. (Symbol) G38-12 (V+) - G38-23 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
4.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the rear television camera assembly with a new or known good one.



b.

Check if the same malfunction recurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY