87940
1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Power Mirror Control System)
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 9 (MV)
Battery negative (-) → Terminal 8 (M+) |
Turns upward |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MV) |
Turns downward |
| Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 8 (M+) |
Turns left |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 4 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the operation of the retractable mirror (w/ Power Retract Mirror).
Disconnect and reconnect the battery between each mirror position check.
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
|---|---|---|
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Forward position (A) | Moves from (A) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position (B) | Moves from (B) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position (B) | Moves from (B) to (A) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Driving position (C) | Moves from (C) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position (D) | Moves from (D) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position (D) | Moves from (D) to (C) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Check the side turn signal light assembly LH (w/ Side Turn Signal Light).
Apply battery voltage to the terminals of the connector, and check the illumination condition.
| Measurement Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 10 (TRNL)
Battery negative (-) → Terminal 6 (GND) |
Side turn light illuminates |
If the result is not as specified, check the side turn signal light assembly LH (Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the mirror light illumination (w/ Outer Mirror Foot Light).
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
| Measurement Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1 (MLP)
Battery negative (-) → Terminal 5 (MLP-) |
Mirror light illuminates |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the operation of the mirror heater (w/ Mirror Heater).
| *a | Component without harness connected
(Outer Rear View mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 (HL+) - Terminal 5 (HL-) | 25°C (75°F) | 6.0 to 9.0 Ω |
If the result is not as specified, check the outer mirror LH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION).
If the result is not as specified, replace the outer rear view mirror assembly LH.
87910
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Power Mirror Control System)
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 9 (MV)
Battery negative (-) → Terminal 8 (M+) |
Turns upward |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MV) |
Turns downward |
| Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 8 (M+) |
Turns left |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 4 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the operation of the retractable mirror (w/ Power Retract Mirror).
Disconnect and reconnect the battery between each mirror position check.
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
|---|---|---|
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Forward position (A) | Moves from (A) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position (B) | Moves from (B) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position (B) | Moves from (B) to (A) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Driving position (C) | Moves from (C) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position (D) | Moves from (D) to (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position (D) | Moves from (D) to (C) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) | Moves from (E) to (C) |
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Check the side turn signal light assembly RH (w/ Side Turn Signal Light).
Apply battery voltage to the terminals of the connector, and check the illumination condition.
| Measurement Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 10 (TRNR)
Battery negative (-) → Terminal 6 (GND) |
Side turn light illuminates |
If the result is not as specified, check the side turn signal light assembly RH (Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY(for Outer Rear View Mirror)>INSPECTION).
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the mirror light illumination (w/Outer Mirror Foot Light).
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage to the terminals of the connector, and check the illumination condition.
| Measurement Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1 (MLP)
Battery negative (-) → Terminal 5 (MLP-) |
Mirror light illuminates |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the operation of the mirror heater (w/ Mirror Heater).
| *a | Component without harness connected
(Outer Rear View mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 (HR+) - Terminal 5 (HR-) | 25°C (75°F) | 6.0 to 9.0 Ω |
If the result is not as specified, check the outer mirror RH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION).
If the result is not as specified, replace the outer rear view mirror assembly RH.