Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3250E _57 Power Source / Network _038063 NETWORKING _0186537 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2789 No Response from ID BOX No communication between the certification ECU and ID code box for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B339675E08
0.208,1.333 3.115,1.531 2.906,0.198 10 false Certification ECU (Smart Key ECU Assembly) 0.219,1.146 0.677,1.344 0.458,0.198 10 false G69 1.823,0.771 2.281,0.969 0.458,0.198 10 false LIN 5.115,0.76 5.573,0.958 0.458,0.198 10 false LIN1 0.646,3.427 2.375,3.656 1.729,0.229 10 false : LIN Communication Line 4.75,3.031 6.323,3.396 1.573,0.365 10 false ID Code Box (Immobiliser Code ECU) 4.74,2.854 5.198,3.052 0.458,0.198 10 false G82 2.094,0.625 2.406,0.823 0.313,0.198 10 false 5 4.917,0.625 5.073,0.823 0.156,0.198 10 false 2 4.917,1.625 5.094,1.844 0.177,0.219 10 false 1 5.083,1.74 5.396,1.938 0.313,0.198 10 false +B 5.083,2.354 5.542,2.552 0.458,0.198 10 false GND 4.927,2.24 5.083,2.438 0.156,0.198 10 false 5 2.813,1.729 3.646,1.948 0.833,0.219 10 false from Battery 3.917,1.917 4.802,2.115 0.885,0.198 10 false ECU-B NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to the Service Bulletin.



HINT:

When the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2789 is not output
DTC B2789 is output



DTC B2789 is not output

DTC B2789 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU])
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU])
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G82 ID code box (immobiliser code ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-5 (LIN) - G82-2 (LIN1) Always Below 1 Ω
G69-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - BATTERY AND BODY GROUND)
a.
B301231C09
1.51,0.24 1.896,0.51 0.385,0.271 0.771,1.563 1.219,1.344 false 2.771,1.583 2.198,1.365 false 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.5,1.5 0.813,1.698 0.313,0.198 10 false +B 2.844,1.521 3.302,1.719 0.458,0.198 10 false GND 1.604,0.292 2.063,0.49 0.458,0.198 10 false G82
*a Front view of wire harness connector
(to ID Code Box [Immobiliser Code ECU])


Disconnect the ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2789 is not output
DTC B2789 is output



DTC B2789 is not output

END (ID CODE BOX [IMMOBILISER CODE ECU] IS DEFECTIVE)

DTC B2789 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)