Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM3250E _52 Drivetrain _038038 DRIVE SHAFT / PROPELLER SHAFT _0187312 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43448G 1.DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

C307716C01
0.49,0.75 0.792,0.823 true 0.833,0.76 1.146,0.958 0.313,0.198 10 false *a
*a Claw Engagement


a.

Using needle-nose pliers, detach the claw engagement and disconnect the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


Hide 43448F 2.DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP LH

a.
C237741

Using pliers, grasp and move the front axle inboard joint boot clamp LH as shown in the illustration to disconnect it from the inboard joint boot.


Hide 3.DISCONNECT INBOARD JOINT BOOT

a.

Disconnect the inboard joint boot from the inboard joint.


Hide 4.REMOVE INBOARD JOINT

C127646C04
2.167,0.396 2.167,0.25 2.167,0.25 1.083,0.25 true 1.833,0.802 1.833,0.25 true 0.875,0.167 1.167,0.354 0.292,0.188 10 *a
*a Matchmark


a.

Remove any old grease from the inboard joint.


b.

Put matchmarks on the inboard joint and front drive outboard joint assembly.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the inboard joint from the front drive outboard joint assembly.


d.
G022501

Using a snap ring expander, remove the snap ring.


e.
C127649C03
2.677,0.76 2.677,1.542 2.677,1.542 2.938,1.542 true 2.802,0.844 2.802,1.531 true 3,1.438 3.313,1.635 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint assembly and tripod joint.

NOTICE:
·

Do not use a punch to make the matchmarks.

·

Only put a matchmark on the front side of the tripod joint, so as not to confuse the installation direction.




f.

Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint




g.

Remove the front No. 2 axle inboard joint boot clamp LH, inboard joint boot and front axle inboard joint boot clamp LH.


Hide 43447F 5.DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

a.
C160725

Using pliers, grasp and move the front No. 2 axle outboard joint boot clamp LH as shown in the illustration to disconnect it from the outboard joint boot.


Hide 43447E 6.DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.


Hide 7.REMOVE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp LH, outboard joint boot and front No. 2 axle outboard joint boot clamp LH from the front drive outboard joint assembly.


b.

Remove any old grease from the front drive outboard joint assembly.


Hide 41336E 8.REMOVE FRONT DRIVE SHAFT DUST COVER LH

F040647N08
2.042,0.854 2.042,0.573 2.042,0.573 2.198,0.573 false 2.26,0.479 2.563,0.635 0.302,0.156 10 false SST

a.

Using SST and a press, remove the front drive shaft dust cover LH from the front drive inboard joint assembly.

SST
09950-00020  


Hide 43502K 9.REMOVE FRONT AXLE HUB DUST SEAL

C034791

a.

Using a screwdriver and hammer, remove the front axle hub dust seal from the front drive outboard joint assembly.