Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184342 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Start the engine
ECO mode switch: Off
Blower switch: LO or more
Temperature settings: MAX HOT
Light control switch: Off
·

Engine coolant temperature 65°C (149°F), or lower (3 PTC heater relays operating)

·

Engine coolant temperature 70°C (158°F), or lower (2 PTC heater relays operating)

·

Engine coolant temperature 75°C (167°F), or lower (A PTC heater relay operating)


Ambient temperature 10°C (50°F) or lower

WIRING DIAGRAM

E312543E20
5.375,4.781 6.927,5.177 1.552,0.396 10 false Air Conditioning Amplifier Assembly 5.354,4.625 5.813,4.823 0.458,0.198 10 false G77 5.302,1.208 5.552,1.385 0.25,0.177 10 false 19 5.313,2.49 5.625,2.656 0.313,0.167 10 false 13 5.323,3.771 5.635,3.938 0.313,0.167 10 false 20 5.615,1.208 6.115,1.385 0.5,0.177 10 false PTC2 5.615,2.49 6.115,2.667 0.5,0.177 10 false PTC1 5.615,3.771 6.115,3.948 0.5,0.177 10 false PTC3 3.26,2.042 4.677,2.208 1.417,0.167 10 false PTC HTR NO.2 3.271,3.302 4.688,3.469 1.417,0.167 10 false PTC HTR NO.1 3.281,4.594 4.698,4.76 1.417,0.167 10 false PTC HTR NO.3 3.302,5.167 3.615,5.333 0.313,0.167 10 false G78 3.385,4.948 3.698,5.115 0.313,0.167 10 false 2 3.302,5.573 3.615,5.74 0.313,0.167 10 false G79 3.396,5.365 3.708,5.531 0.313,0.167 10 false 3 3.302,5.969 3.615,6.135 0.313,0.167 10 false G79 3.406,5.771 3.719,5.938 0.313,0.167 10 false 1 1.958,5.167 2.271,5.333 0.313,0.167 10 false G78 2.042,4.948 2.354,5.115 0.313,0.167 10 false 1 1.948,5.969 2.26,6.135 0.313,0.167 10 false G79 2.042,5.76 2.354,5.927 0.313,0.167 10 false 2 2.063,6.25 3.875,6.417 1.813,0.167 10 false Quick Heater Assembly 2.063,4.427 3.021,4.781 0.958,0.354 10 false CDS FAN/PTC HTR NO.3 2.063,3.146 3.167,3.354 1.104,0.208 10 false PTC HTR NO.1 2.031,1.875 3.125,2.073 1.094,0.198 10 false PTC HTR NO.2 4.26,4.156 4.573,4.323 0.313,0.167 10 false 3 3.104,4.156 3.417,4.323 0.313,0.167 10 false 5 4.26,3.76 4.573,3.927 0.313,0.167 10 false 1 3.104,3.76 3.417,3.927 0.313,0.167 10 false 2 4.25,2.875 4.563,3.042 0.313,0.167 10 false 3 3.104,2.854 3.417,3.021 0.313,0.167 10 false 5 4.25,2.469 4.563,2.635 0.313,0.167 10 false 2 3.104,2.469 3.417,2.635 0.313,0.167 10 false 1 4.26,1.604 4.573,1.771 0.313,0.167 10 false 3 4.25,1.208 4.563,1.375 0.313,0.167 10 false 2 3.104,1.615 3.417,1.781 0.313,0.167 10 false 5 3.104,1.208 3.417,1.375 0.313,0.167 10 false 1 1.927,0.635 3.24,0.833 1.313,0.198 10 false from Battery 1.01,0.302 1.917,0.448 0.906,0.146 10 false IG1 NO.4 1.917,0.135 4.948,0.385 3.031,0.25 10 false from Ignition Switch*1, IG1 NO.1 Relay*2 3.073,5.083 3.385,5.25 0.313,0.167 10 false B 2.333,5.083 2.646,5.25 0.313,0.167 10 false E 3.083,5.479 3.396,5.646 0.313,0.167 10 false B 3.073,5.875 3.385,6.042 0.313,0.167 10 false B 2.344,5.896 2.656,6.063 0.313,0.167 10 false E 5.094,6 7.052,6.198 1.958,0.198 10 false *1: w/o Entry and Start System 5.094,6.354 7.052,6.552 1.958,0.198 10 false *2: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT PTC HEATER RELAY (PTC HTR NO.1, PTC HTR NO.2, PTC HTR NO.3)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)

NG

REPLACE PTC HEATER RELAY (PTC HTR NO.1, PTC HTR NO.2, PTC HTR NO.3)

2.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.2:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.3:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Disconnect the G77 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
Relay terminal 2 - G77-13 (PTC1) Always Below 1 Ω
Relay terminal 2 or G77-13 (PTC1)- Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
Relay terminal 2 - G77-19 (PTC2) Always Below 1 Ω
Relay terminal 2 or G77-19 (PTC2) - Body ground Always 10 kΩ or higher

PTC HTR NO.3:
Tester Connection Condition Specified Condition
Relay terminal 1 - G77-20 (PTC3) Always Below 1 Ω
Relay terminal 1 or G77-20 (PTC3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - PTC HEATER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - PTC HEATER RELAY AND BODY GROUND)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Disconnect the G78 and G79 quick heater assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO.1:
Tester Connection Condition Specified Condition
G79-3 - Relay terminal 3 Always Below 1 Ω
G78-1 - Body ground Always Below 1 Ω
G79-2 - Body ground Always Below 1 Ω
G78-3 or relay terminal 3 - Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
G79-1 - Relay terminal 3 Always Below 1 Ω
G79-2 - Body ground Always Below 1 Ω
G79-1 or relay terminal 3 - Body ground Always 10 kΩ or higher

PTC HTR NO.3:
Tester Connection Condition Specified Condition
G78-2- Relay terminal 3 Always Below 1 Ω
G78-1 - Body ground Always Below 1 Ω
G78-2 or relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT QUICK HEATER ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

NG