Home › Engine / Hybrid System › 2GD-FTV FUEL › FUEL SENDER GAUGE ASSEMBLY
RM3250E _51 Engine / Hybrid System _038007 2GD-FTV FUEL _0187759 FUEL SENDER GAUGE ASSEMBLY G

2GD-FTV FUEL  FUEL SENDER GAUGE ASSEMBLY  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY (for Short Wheelbase)

a.

Check the fuel sender gauge assembly output voltage.

i.
A339767C01
1.75,0.688 2.208,0.302 2.208,0.302 2.375,0.302 true 2.188,0.688 2.677,0.688 true 0.083,0.094 0.438,0.354 0.354,0.26 10 false *a 1.625,1.719 1.906,1.969 0.281,0.25 10 false *b 2.771,0.594 3.042,0.802 0.271,0.208 10 false FV 2.458,0.229 2.729,0.427 0.271,0.198 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A339574C01
0.75,0.844 1.25,0.844 true 1.708,0.917 1.708,1.323 true 0.781,3.01 1.208,3.01 true 0.719,4.135 1.146,4.135 true 0.063,0.042 0.313,0.229 0.25,0.188 10 false *a 0.583,2.938 0.813,3.125 0.229,0.188 10 false F 0.51,4.052 0.729,4.25 0.219,0.198 10 false E 0.479,0.76 0.74,0.979 0.26,0.219 10 false FR 1.625,1.354 1.854,1.552 0.229,0.198 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.25 to 4.61 V*
Float position is E (lower) 0.34 to 0.70 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage (F) = (0.850 x Voltage applied to terminals) to (0.922 x Voltage applied to terminals)

·

Output voltage (E) = (0.068 x Voltage applied to terminals) to (0.140 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.



Hide 83320 2.INSPECT FUEL SENDER GAUGE ASSEMBLY (for Long Wheelbase)

a.

Check the fuel sender gauge assembly output voltage.

i.
A339767C01
1.75,0.688 2.208,0.302 2.208,0.302 2.375,0.302 true 2.188,0.688 2.677,0.688 true 0.083,0.094 0.438,0.354 0.354,0.26 10 false *a 1.625,1.719 1.906,1.969 0.281,0.25 10 false *b 2.771,0.594 3.042,0.802 0.271,0.208 10 false FV 2.458,0.229 2.729,0.427 0.271,0.198 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A339573C01
0.313,2.292 0.792,2.292 true 0.271,4.292 0.688,4.292 true 0.802,0.927 1.281,0.927 true 1.729,0.948 1.729,1.333 true 0.052,0.042 0.302,0.24 0.25,0.198 10 false *a 0.104,4.208 0.313,4.396 0.208,0.188 10 false E 0.135,2.208 0.365,2.417 0.229,0.208 10 false F 0.552,0.844 0.844,1.052 0.292,0.208 10 false FR 1.635,1.396 1.896,1.604 0.26,0.208 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.25 to 4.61 V*
Float position is E (lower) 0.34 to 0.70 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage (F) = (0.850 x Voltage applied to terminals) to (0.922 x Voltage applied to terminals)

·

Output voltage (E) = (0.068 x Voltage applied to terminals) to (0.140 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.