Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM
RM3250E _59 Vehicle Exterior _038067 LIGHTING (EXT) _0188980 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Leveling ECU Power Source Circuit  


DESCRIPTION

This circuit detects the state of the engine switch, and sends it to the headlight leveling ECU assembly.

WIRING DIAGRAM

E317278E02
2.698,1.125 3.927,1.323 1.229,0.198 10 false IG1 NO.4 0.24,0.938 1.573,1.146 1.333,0.208 10 false from IG1 NO.1 Relay 3.656,0.833 3.885,1.031 0.229,0.198 10 false 1 3.667,1.438 3.896,1.635 0.229,0.198 10 false 9 3.75,2.188 4.979,2.385 1.229,0.198 10 false G80 3.854,1.438 5.083,1.635 1.229,0.198 10 false E1 3.854,0.833 5.083,1.031 1.229,0.198 10 false IG 4.917,1.188 6.146,1.385 1.229,0.198 10 false CPU 3.76,2.323 6.083,2.5 2.323,0.177 10 false Headlight Leveling ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the display on the GTS.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+B IG power supply voltage value 0.00 to 19.75 V 11.00 to 14.00 V -
Body Electrical > HL AutoLeveling > Data List
Tester Display
+B
50003 361 5
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY)
a.

Disconnect the G80 headlight leveling ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the G80 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-9 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR