Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2015.06–2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189243 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.


a.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector


OK:

No defects are found.


If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

E315463C03
6,0.76 6.354,0.979 0.354,0.219 5.188,0.99 5.542,1.208 0.354,0.219 3.115,1.583 3.469,1.802 0.354,0.219 3.219,6.135 3.573,6.354 0.354,0.219 1.031,6.313 1.385,6.531 0.354,0.219 6,1.042 6.354,1.26 0.354,0.219 2.969,6.5 3.719,6.5 true 2.813,5.823 2.813,5.302 2.813,5.302 3.198,5.302 true 2.177,5.333 2.417,5.333 2.417,5.333 2.729,5.969 true 2.031,5.583 2.396,5.583 2.396,5.583 2.729,6.104 true 2.24,7.188 2.24,6.521 2.24,6.521 2.719,6.365 true 2.49,6.99 2.49,6.615 2.49,6.615 2.719,6.5 true 2.969,6.219 3.229,5.979 3.229,5.979 3.823,5.979 true 2.979,6.083 3.24,5.844 3.24,5.844 3.479,5.844 true 2.969,5.938 3.229,5.698 3.229,5.698 3.823,5.698 true 1.083,5.76 1.458,5.76 1.458,5.76 1.865,6.083 true 1.156,5.99 1.448,5.99 1.448,5.99 1.854,6.313 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 6.104,0.802 6.417,1 0.313,0.198 10 false z1 5.302,1.031 5.615,1.229 0.313,0.198 10 false z2 3.229,1.635 3.542,1.833 0.313,0.198 10 false z3 3.302,6.177 3.615,6.375 0.313,0.198 10 false G4 1.115,6.354 1.427,6.552 0.313,0.198 10 false G5 3.271,5.198 3.729,5.396 0.458,0.198 10 false CCS 1.854,5.24 2.313,5.438 0.458,0.198 10 false ECC 1.698,5.5 2.156,5.698 0.458,0.198 10 false EAU 3.875,5.583 4.333,5.781 0.458,0.198 10 false HO 2.115,7.219 2.573,7.417 0.458,0.198 10 false AU2 2.365,7.01 2.823,7.208 0.458,0.198 10 false AU1 3.531,5.74 3.99,5.938 0.458,0.198 10 false +DP 3.885,5.875 4.344,6.073 0.458,0.198 10 false +DP2 3.771,6.448 4.229,6.646 0.458,0.198 10 false IL+2 0.854,5.656 1.177,5.875 0.323,0.219 10 false D+ 0.969,5.906 1.292,6.125 0.323,0.219 10 false D- 6.104,1.083 6.417,1.281 0.313,0.198 10 false z4 6.406,0.771 6.74,1.01 0.333,0.24 12 false *A 6.406,1.063 6.74,1.302 0.333,0.24 12 false *B
*A w/o Steering Pad Switch *B w/ Cruise Control System
*a Component without harness connected
(Spiral Cable Sub-assembly)
- -
V100144

Interlock - -


NOTICE:

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.


i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-1 (CCS) - z4-3 Always 3 Ω or less
G4-2 (ECC) - z4-4
G4-3 (EAU) - z2-8
G4-5 (AU2) - z2-10
G4-6 (AU1) - z2-11
G4-9 (HO) - z1-2
*1
G4-9 (HO) - z2-1
*2
G4-10 (+DP) - z2-2
G4-11 (+DP2) - z2-3
G4-13 (IL+2) - z2-5
G5-1 (D+) - z3-2 Below 1 Ω
G5-2 (D-) - z3-1


*1: w/o Steering Pad Switch:

*2: w/ Steering Pad Switch:


iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-1 (CCS) - z4-3 Always 3 Ω or less
G4-2 (ECC) - z4-4
G4-3 (EAU) - z2-8
G4-5 (AU2) - z2-10
G4-6 (AU1) - z2-11
G4-9 (HO) - z1-2
*1
G4-9 (HO) - z2-1
*2
G4-10 (+DP) - z2-2
G4-11 (+DP2) - z2-3
G4-13 (IL+2) - z2-5
G5-1 (D+) - z3-2 Below 1 Ω
G5-2 (D-) - z3-1


*1: w/o Steering Pad Switch:

*2: w/ Steering Pad Switch:


iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-1 (CCS) - z4-3 Always 3 Ω or less
G4-2 (ECC) - z4-4
G4-3 (EAU) - z2-8
G4-5 (AU2) - z2-10
G4-6 (AU1) - z2-11
G4-9 (HO) - z1-2
*1
G4-9 (HO) - z2-1
*2
G4-10 (+DP) - z2-2
G4-11 (+DP2) - z2-3
G4-13 (IL+2) - z2-5
G5-1 (D+) - z3-2 Below 1 Ω
G5-2 (D-) - z3-1


*1: w/o Steering Pad Switch:

*2: w/ Steering Pad Switch:

If the result is not as specified, replace the spiral cable sub-assembly.