Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › 2015.06–2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189245 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

·

If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

B401137



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 73960A 2.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the instrument panel passenger airbag assembly, use an unneeded vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




d.

Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


e.

Disconnect the No. 2 instrument panel wire.

i.
B399329C01
0,0 0,0 false
V113147

Slide in this Direction


Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

i.
B409639N01
0.677,2.219 1.615,2.219 1.615,2.219 1.615,2.656 true 0.969,2.656 0.969,2.219 true 0.302,2.135 0.688,2.313 0.385,0.177 10 true SST

Connect the SST connector to the No. 2 instrument panel wire.

SST
09082-00700  09082-00760  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.


CAUTION:
·
B394923

Do not place objects on top of the airbag door.

·

If deployed with an object on top of the airbag door, the door glass and windshield may break and fly off, causing serious injuries.

·
B394922

Do not deploy if the instrument panel passenger airbag assembly is loose.

·

If deployed while the instrument panel passenger airbag assembly is loose, the instrument panel passenger airbag assembly may fly off and cause serious injuries.




ii.
B340835C02
0.729,1.521 0.646,0.917 0.646,0.917 0.521,0.917 false 1.604,1.896 1.917,2.052 0.313,0.156 10 false *a 0.208,0.844 0.667,1.042 0.458,0.198 10 false SST
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iii.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Remove the instrument panel passenger airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·
B399176

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394926

Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.

·

If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394928

Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.

·

If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the instrument panel passenger airbag assembly in a plastic bag.




i.

Dispose of the instrument panel passenger airbag assembly.

i.

Place the instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B394925

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394927

Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.

·

If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394929

Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.

·

If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394912

Never dispose of an instrument panel passenger airbag assembly with an undeployed airbag.

·

If an undeployed instrument panel passenger airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 73960A 3.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  


b.

Remove the instrument panel passenger airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Install SST.

i.
B409640N01
2.115,2.052 2.552,1.51 2.552,1.51 2.833,1.51 false 2.635,1.979 2.552,1.521 false 2.906,1.427 3.365,1.625 0.458,0.198 10 false SST

After connecting the following SST to each other, connect them to the instrument panel passenger airbag assembly.

SST
09082-00802  (09082-10801, 09082-40800)



d.
B104882C28
1.99,1.594 1.99,1.25 false 2.656,0.51 2.969,0.667 0.313,0.156 10 *a 1.917,1.625 2.229,1.781 0.313,0.156 10 *b
*a Wire Diameter
*b Stripped Wire


Using braided wire, tie down the instrument panel passenger airbag assembly to an unneeded tire.

Wire:
Cross-sectional area of stripped wire:

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the instrument panel passenger airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.

Position the instrument panel passenger airbag assembly inside the tire with the airbag deployment side facing inside.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


B409641C01
2.24,1.708 3.281,1.448 true 1.802,0.167 2.115,0.323 0.313,0.156 10 false *a 1.125,1.729 1.438,1.885 0.313,0.156 10 false *b 3.333,1.344 3.646,1.5 0.313,0.156 10 false *c
*a Width *b Inner Diameter
*c Deployment Side - -


CAUTION:
B399179C01
0.563,1.458 1.219,1.021 true 0.406,1.385 0.625,1.573 0.219,0.188 10 false *a
*a Remove looseness
V100155

Deployment Side


·

Do not install the instrument panel passenger airbag assembly with the deployment side facing outside.

·

When securing the instrument panel passenger airbag assembly, make sure there is no looseness in the wire harness.

·

If the deployment side is facing outside or the wire harness is loosely wrapped, the deployed instrument panel passenger airbag assembly and tire may fly off and cause serious injuries.



NOTICE:

The tires may be damaged by the airbag deployment, so use unneeded tires.




e.

Place the tires.

i.
B409642C01
2.094,1.458 2.375,1.458 true 2.125,1.719 2.375,1.719 2.375,1.719 2.375,0.896 true 2.125,1.167 2.365,1.167 true 2.115,0.896 2.552,0.896 true 2.583,0.802 2.802,0.99 0.219,0.188 10 false *a
*a Tires (2 or more)


Place at least 2 tires under the tire to which the instrument panel passenger airbag assembly is tied.


ii.

Place at least 2 tires onto the tire to which the instrument panel passenger airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.
B105087

Tie the tires together with the 2 wires.



f.

Install SST.

i.
B409643C01
2.104,2.948 2.417,3.104 0.313,0.156 10 false *a
*a 10 m or more


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the instrument panel passenger airbag assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B401667

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the instrument panel passenger airbag assembly.

CAUTION:
·
B394925

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394927

Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.

·

If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394929

Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.

·

If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394912

Never dispose of an instrument panel passenger airbag assembly with an undeployed airbag.

·

If an undeployed instrument panel passenger airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the instrument panel passenger airbag assembly from the wheel.


ii.

Place the instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.