Home › Vehicle Interior › LIGHTING (INT) › PERSONAL LIGHT
RM3250E _58 Vehicle Interior _038066 LIGHTING (INT) _0189510 PERSONAL LIGHT G

LIGHTING (INT)  PERSONAL LIGHT  INSPECTION  


PROCEDURE

Hide 81260A 1.INSPECT MAP LIGHT ASSEMBLY (PERSONAL LIGHT) (w/o Microphone)

a.
B405405C01
2.719,1.271 2.125,1.396 true 1.75,1.896 1.719,1.51 true 1.333,1.396 0.625,1.26 true 0.135,0.052 0.448,0.208 0.313,0.156 10 false *a 0.323,1.146 0.708,1.344 0.385,0.198 10 false CTY 1.729,1.927 1.958,2.125 0.229,0.198 10 false B 2.771,1.167 3.229,1.365 0.458,0.198 10 false GND
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (B) - 1 (GND) Map light switch LH OFF, RH OFF 10 kΩ or higher
Map light switch LH ON, RH OFF Below 1 Ω
Map light switch LH ON, RH ON Below 1 Ω
Map light switch LH OFF, RH ON Below 1 Ω
2 (B) - 3 (CTY) Courtesy switch OFF position 10 kΩ or higher
Courtesy switch DOOR position Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).


Hide 81260A 2.INSPECT MAP LIGHT ASSEMBLY (PERSONAL LIGHT) (w/ Microphone)

a.
E317492C02
2.458,1.156 2.792,1.042 true 2.01,1.083 2.083,0.396 true 1.646,1.083 1.479,0.396 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 2.865,0.948 3.323,1.146 0.458,0.198 10 false CTY 1.417,0.229 1.573,0.427 0.156,0.198 10 false B 1.948,0.219 2.406,0.417 0.458,0.198 10 false GND
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (B) - 3 (GND) Map light switch LH OFF, RH OFF 10 kΩ or higher
Map light switch LH ON, RH OFF Below 1 Ω
Map light switch LH ON, RH ON Below 1 Ω
Map light switch LH OFF, RH ON Below 1 Ω
5 (B) - 1 (CTY) Courtesy switch OFF position 10 kΩ or higher
Courtesy switch DOOR position Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).


b.

Disconnect the telephone microphone assembly connector.


c.
E324485C01
1.604,0.25 1.885,0.479 0.281,0.229 1.583,2.125 1.865,2.354 0.281,0.229 1.115,3.167 1.365,2.802 true 2.01,3.156 1.802,2.802 true 2.792,2.667 2.458,2.74 true 1.24,1.365 0.635,1.24 true 1.281,1.844 1.479,1.417 true 2.167,1.823 1.656,1.406 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 1.698,0.281 1.875,0.448 0.177,0.167 10 false A 1.677,2.167 1.854,2.333 0.177,0.167 10 false B 0.188,1.135 0.802,1.333 0.615,0.198 10 false MACC 1.083,1.875 1.698,2.073 0.615,0.198 10 false MCO+ 2.115,1.844 2.729,2.042 0.615,0.198 10 false MCO- 1.938,3.188 2.552,3.385 0.615,0.198 10 false MIC+ 2.854,2.573 3.396,2.771 0.542,0.198 10 false MACC 0.958,3.198 1.573,3.396 0.615,0.198 10 false MIC-
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A15 (MACC) - B5 (MACC) Always Below 1 Ω
A14 (MCO+) - B3 (MIC+) Always Below 1 Ω
A13 (MCO-) - B2 (MIC-) Always Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).