This DTC is stored if the combustion state of any cylinder is unstable.
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1605 | Rough Idling | When idling with the accelerator pedal released and the vehicle stopped, this item detects when the combustion is unstable from the sudden changes in engine speed between the cylinders. Detection for 2 to 10 seconds according to the combustion state. (1 trip detection logic). | ·
Injector assembly ·
Injector compensation code ·
Fuel leak ·
Glow system ·
Intake air system leakage ·
Intake system blockage ·
EGR system ·
Throttle valve system ·
Pre-stroke control valve ·
Low quality fuel ·
Fuel filter element assembly air bleed problem ·
Accessory problem (A/C, generator, etc.) ·
Engine assembly ·
ECM |
- | DTC stored |
| DTC No. | Data List |
|---|---|
| P1605 | ·
Target Idle Engine Speed ·
Engine Speed ·
MAP ·
MAF ·
Coolant Temp ·
Battery Voltage ·
Engine Speed of Cyl #1 (to #4) (Output only when the "Check the Cylinder Compression" Active Test is performed) ·
Intake Air ·
Target Common Rail Pressure ·
Common Rail Pressure ·
Injection Feedback Val #1 (to #4) ·
Injection Volume ·
Actual Throttle Position ·
Target EGR Valve Pos ·
Actual EGR Valve Pos ·
EGR Close Lrn. Val. ·
Rough Idle #1 (to #4) ·
Plural Cylinders Rough Idle |
In order for idling to be stable, glow system operation, fuel system operation and compression sufficient to maintain the target idling speed are necessary.
Glow system
The following malfunctions may be present in the glow system.
Engine coolant temperature sensor malfunction.
Glow plug malfunction.
Glow plug controller malfunction.
Fuel system
The following malfunctions may be present in the fuel system.
Fuel leakage.
Problem with injector assemblies.
Problem with fuel supply pump assembly.
Air in fuel pipe.
Engine assembly
The following malfunctions may be present in the engine assembly.
Insufficient compression.
In contrast to conventional DTCs for components, circuits and systems, DTC P1605 is used to estimate the malfunctioning area from problem symptoms and freeze frame data in response to symptoms such as "rough idling", "strong engine vibrations", etc. Such problem symptoms can occur even in the following conditions:
Driving with long-stored fuel (fuel that has remained in the tank for long periods of time)
Using fuel not acclimated to the climate during a change of seasons
Temporarily using low-quality fuel (fuel that contains water or has poor fuel properties)
If any other DTCs are output, perform troubleshooting for those DTCs first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Record the stored DTC and freeze frame data.
This freeze frame data shows the actual engine conditions when air fuel ratio too rich trouble occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P1605 is output | A |
| P1605 and other DTCs are output | B |
If any DTCs other than P1605 are output, troubleshoot those DTCs first.
A
B
Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.
| Judgment of Data List Values | Problem Cause | Diagnosis Note | Proceed to |
|---|---|---|---|
| Any of Rough Idle #1 to #4 in the freeze frame data is ON | Injector assembly | If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected.
|
A |
| Judgment of Data List Values | Problem Cause | Diagnosis Note | Proceed to |
|---|---|---|---|
| Any of Injection Feedback Val #1 to #4 in the freeze frame data is more than 3.0 mm3/st | Injector assembly | If the cylinder that displays Rough Idle ON also has a value of more than 3.0 mm3/st for Injection Feedback Val, improper combustion in that cylinder is suspected. | A |
| Judgment of Data List Values | Problem Cause | Diagnosis Note | Proceed to |
|---|---|---|---|
| Plural Cylinders Rough Idle in the freeze frame data is ON | ·
EGR system ·
Diesel throttle system ·
Fuel supply pump assembly ·
Low-quality fuel |
When EGR Rate Differential (Actual-Target) increases by more than 30%, there may be a malfunction in the EGR system. | B |
| When there is data stored that indicates that Common Rail Pressure is low compared to Target Common Rail Pressure, there may be a malfunction in the fuel pressure control system, such as in the fuel supply pump assembly. | C | ||
| When data indicating that MAP is low (50 kPa or less) is stored, there may be a stuck closed malfunction in the diesel throttle system or EGR valve. | - |
A
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>Rough Idling or Excessive Engine Vibrations
B
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>Rough Idling or Excessive Engine Vibrations
C
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>Rough Idling or Excessive Engine Vibrations