Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0189557 ECD SYSTEM C

2GD-FTV ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail assembly using the fuel pressure sensor, and controls the pre-stroke control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A208460E63
2.781,0.51 2.938,0.365 2.938,0.365 2.99,0.365 false 3.135,2.198 3.24,2.146 3.24,2.146 3.281,2.146 false 1.948,1.646 2.177,1.646 false 2.229,1.104 2.5,1.104 false 1.406,0.531 0.938,0.646 false 0.063,0.042 1.792,0.271 1.729,0.229 10 false Property of Output Voltage: 1.052,0.406 1.417,0.594 0.365,0.188 10 false 5.00 0.625,0.573 0.948,0.813 0.323,0.24 10 false 4.90 2.208,1.573 2.958,1.844 0.75,0.271 10 false RR2 (Sub) 1.542,1.021 2.198,1.271 0.656,0.25 10 false RR (Main) 1.052,0.625 1.49,0.813 0.438,0.188 10 false 4.61 1.052,0.823 1.406,1.021 0.354,0.198 10 false 4.11 1.052,1.708 1.417,1.917 0.365,0.208 10 false 1.35 1.052,1.906 1.385,2.073 0.333,0.167 10 false 0.85 1.052,2.083 1.427,2.25 0.375,0.167 10 false 0.55 1.24,2.219 1.417,2.406 0.177,0.188 10 false 0 2.938,2.333 3.604,2.573 0.667,0.24 10 false 233000 1.125,2.438 3.24,2.667 2.115,0.229 10 false Common Rail Pressure (kPa) 3.323,2.063 4.219,2.281 0.896,0.219 10 false Stores P0192 3.021,0.281 3.969,0.563 0.948,0.281 10 false Stores P0193 0.063,1.115 1.25,1.406 1.188,0.292 10 false Output Voltage (V) 5.198,1.177 5.656,1.438 0.458,0.26 10 false Main 5.26,1.917 5.604,2.135 0.344,0.219 10 false Sub 6.729,1.177 7.156,1.365 0.427,0.188 10 false PCR1 6.74,1.375 7.104,1.563 0.365,0.188 10 false E2M 6.74,1.74 7.125,1.969 0.385,0.229 10 false VCS 6.729,1.938 7.146,2.156 0.417,0.219 10 false PCR2 5.875,0.625 6.365,0.833 0.49,0.208 10 false VCM 6.375,2.438 6.75,2.677 0.375,0.24 10 false E2S 4.219,0.042 6.729,0.542 2.51,0.5 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low Fuel pressure sensor output voltage stays at fixed value a certain number of times (0.1 seconds or more).
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Ran out of fuel

·

Fuel frozen

·

ECM


Comes on DTC stored
P0190 Fuel Rail Pressure Sensor Circuit Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0192 Fuel Rail Pressure Sensor Circuit Low Input Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored

Related Data List
DTC No. Data List
P0087
·

Common Rail Pressure

·

Target Common Rail Pressure


P0190
P0192
P0193

HINT:
·

Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure. Under stable conditions, the difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

·

Black smoke

·

Poor drivability

·

Lack of power

·

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

·

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Common Rail Pressure" always displays 0 kPa or 240000 kPa.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0087 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds
P0190 Ignition switch ON for 1 second or more
P0192
P0193

MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 25000 to 45000 kPa (255 to 459 kgf/cm2, 3625 to 6525 psi) when idling, and it increases to approximately 60000 to 95000 kPa (612 to 969 kgf/cm2, 8700 to 13775 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

A175676E08
4.99,0.885 5.458,0.521 5.458,0.521 5.615,0.521 false 4.802,1.771 4.677,1.771 4.677,1.771 4.188,1.427 false 0.063,0.031 1.917,0.302 1.854,0.271 10 false P0087 Malfunction Detection 2.271,0.552 3.229,0.771 0.958,0.219 10 false Fuel Pressure 4.844,1.677 5.51,1.875 0.667,0.198 10 false Abnormal 5.656,0.427 6.24,0.625 0.583,0.198 10 false Normal 2.292,2.156 3.302,2.417 1.01,0.26 10 false Engine Speed 5.229,3.375 5.635,3.583 0.406,0.208 10 false Time

·

Even if the system is normal, DTCs may be stored due to a drop in the fuel pressure after running out of fuel, etc. If DTCs P0087 and P1603 are both stored, clear these DTCs and perform a DTC check again.



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A348536E05
0.469,3.083 0.781,3.281 0.313,0.198 10 false Z2 0.448,3.271 1.938,3.521 1.49,0.25 10 false Fuel Pressure Sensor 1.698,0.531 2.01,0.729 0.313,0.198 10 false PR 1.719,0.958 2.031,1.156 0.313,0.198 10 false E2 1.698,1.385 2.01,1.583 0.313,0.198 10 false VC 1.635,1.792 1.948,1.99 0.313,0.198 10 false PR2 1.604,2.219 1.917,2.417 0.313,0.198 10 false E2S 1.979,2.76 2.292,2.958 0.313,0.198 10 false 1 5.26,0.542 5.573,0.74 0.313,0.198 10 false C59 5.594,0.656 6.146,0.854 0.552,0.198 10 false PCR1 5.594,1.083 5.906,1.281 0.313,0.198 10 false E2M 5.604,1.5 6.063,1.708 0.458,0.208 10 false VCM 5.594,1.906 6.083,2.094 0.49,0.188 10 false PCR2 5.604,2.323 5.917,2.521 0.313,0.198 10 false E2S 1.604,2.646 1.917,2.844 0.313,0.198 10 false VCS 5.583,2.75 5.896,2.948 0.313,0.198 10 false VCS 5.26,0.958 5.573,1.156 0.313,0.198 10 false C59 5.25,1.375 5.563,1.573 0.313,0.198 10 false C59 5.25,1.802 5.563,2 0.313,0.198 10 false C60 5.25,2.219 5.563,2.417 0.313,0.198 10 false C60 5.25,2.635 5.563,2.833 0.313,0.198 10 false C60 5.938,3.073 6.427,3.271 0.49,0.198 10 false ECM 1.99,1.917 2.302,2.115 0.313,0.198 10 false 2 1.99,2.333 2.302,2.531 0.313,0.198 10 false 3 1.979,1.083 2.292,1.281 0.313,0.198 10 false 4 1.979,0.656 2.292,0.854 0.313,0.198 10 false 5 1.979,1.5 2.292,1.698 0.313,0.198 10 false 6 5.292,0.344 5.604,0.542 0.313,0.198 10 false 18 5.292,0.76 5.604,0.958 0.313,0.198 10 false 19 5.292,1.188 5.604,1.385 0.313,0.198 10 false 28 5.292,1.615 5.604,1.813 0.313,0.198 10 false 26 5.292,2.021 5.604,2.219 0.313,0.198 10 false 25 5.292,2.438 5.604,2.635 0.313,0.198 10 false 33

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0190, P0192 or P0193 is output A
P0087 is output* B



HINT:

*: If DTCs P0087 and P1603 are stored, these DTCs may have been stored due to a drop in the fuel pressure after running out of fuel, etc. Therefore, clear these DTCs and perform a DTC check to confirm whether they are output again.



A

2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

B

8.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A257437C94
1.302,0.896 1.656,1.146 0.354,0.25 1.802,0.896 2.167,1.146 0.365,0.25 1.5,2.333 1.656,1.698 true 1.125,2.344 1.615,1.635 true 2,2.323 1.781,1.708 true 2.563,2.365 1.823,1.646 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.354,0.938 1.719,1.177 0.365,0.24 10 false C59 1.26,2.375 1.99,2.583 0.729,0.208 10 false 28 (VCM) 0.583,2.375 1.281,2.625 0.698,0.25 10 false 19 (E2M) 1.917,2.375 2.615,2.594 0.698,0.219 10 false 33 (VCS) 2.563,2.375 3.271,2.573 0.708,0.198 10 false 25 (E2S) 1.844,0.938 2.208,1.208 0.365,0.271 10 false C60
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C59-28 (VCM) - C59-19 (E2M) Ignition switch ON 4.5 to 5.5 V
C60-33 (VCS) - C60-25 (E2S) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)

NG

11.REPLACE ECM
3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)
a.
A257437C95
1.302,0.896 1.656,1.146 0.354,0.25 1.802,0.896 2.167,1.146 0.365,0.25 1.5,2.333 1.656,1.646 true 0.875,2.344 1.615,1.635 true 2,2.323 1.781,1.635 true 2.542,2.396 1.823,1.646 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.354,0.938 1.719,1.177 0.365,0.24 10 false C59 1.115,2.385 1.792,2.594 0.677,0.208 10 false 18 (PCR1) 0.479,2.375 1.208,2.635 0.729,0.26 10 false 19 (E2M) 1.823,2.396 2.729,2.635 0.906,0.24 10 false 26 (PCR2) 2.563,2.396 3.24,2.604 0.677,0.208 10 false 25 (E2S) 1.844,0.938 2.208,1.208 0.365,0.271 10 false C60
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C59-18 (PCR1) - C59-19 (E2M) Idling 1.8 to 2.1 V
C60-26 (PCR2) - C60-25 (E2S) Idling 1.2 to 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the ignition switch to ON.


b.

Connect the GTS to the DLC3.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON for 1 second or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0190, P0192 or P0193 is output A
DTC is not output B




B

A

11.REPLACE ECM
5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A204375C20
0.563,1.135 0.948,1.375 0.385,0.24 1.073,0.781 1.427,1.052 true 1.094,1.615 1.417,1.323 true 2.323,1.5 1.958,1.323 true 1.938,1.031 2.271,0.729 true 0.75,0.667 1.115,0.865 0.365,0.198 10 false VCS 0.688,1.167 1.01,1.365 0.323,0.198 10 false Z2 2.313,0.646 2.771,0.844 0.458,0.198 10 false E2S 0.885,1.615 1.26,1.802 0.375,0.188 10 false E2 2.365,1.49 2.833,1.698 0.469,0.208 10 false VC 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z2-6 (VC) - Z2-4 (E2) Ignition switch ON 4.5 to 5.5 V
Z2-1 (VCS) - Z2-3 (E2S) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z2-5 (PR) - C59-18 (PCR1) Always Below 1 Ω
Z2-4 (E2) - C59-19 (E2M) Always Below 1 Ω
Z2-2 (PR2) - C60-26 (PCR2) Always Below 1 Ω
Z2-3 (E2S) - C60-25 (E2S) Always Below 1 Ω
Z2-5 (PR) or C59-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
Z2-2 (PR2) or C60-26 (PCR2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.CHECK ECM (CHECK RESISTANCE)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the fuel pressure sensor connector.


b.
A204375C21
0.563,1.135 0.948,1.375 0.385,0.24 1.073,0.781 1.427,1.052 true 1.094,1.615 1.417,1.323 true 2.281,1.625 1.958,1.323 true 1.938,1.031 2.271,0.729 true 1.708,1 1.896,0.365 1.896,0.365 2.042,0.365 true 1.646,1.844 1.521,1.844 1.521,1.844 1.688,1.344 true 0.75,0.667 1.115,0.865 0.365,0.198 10 false VCS 0.688,1.167 1.01,1.365 0.323,0.198 10 false Z2 2.302,0.667 2.76,0.865 0.458,0.198 10 false E2S 0.885,1.615 1.26,1.802 0.375,0.188 10 false E2 2.333,1.625 2.802,1.833 0.469,0.208 10 false VC 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 1.708,1.781 2.083,1.969 0.375,0.188 10 false PR 2.094,0.292 2.552,0.49 0.458,0.198 10 false PR2
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Z2-6 (VC) - Z2-5 (PR) Ignition switch off No short or open circuit
Z2-5 (PR) - Z2-4 (E2) Ignition switch off No short or open circuit
Z2-1 (VCS) - Z2-2 (PR2) Ignition switch off No short or open circuit
Z2-2 (PR2) - Z2-3 (E2S) Ignition switch off No short or open circuit



c.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

11.REPLACE ECM
8.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2GD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.BLEED AIR FROM FUEL SYSTEM
9.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED