Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE(w/o ABS)
RM3250E _54 Brake _038045 BRAKE SYSTEM (OTHER) _0189595 LOAD SENSING PROPORTIONING VALVE(w/o ABS) G

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE(w/o ABS)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 47900 1.CHECK LOAD SENSING PROPORTIONING VALVE ASSEMBLY

C283545C03
2.156,0.563 2.469,0.719 0.313,0.156 10 false *a
*a Weight


a.

Set the vehicle to its curb weight.


b.

Place weights (as necessary) on the rear deck until the rear axle load is as shown below.

Standard Rear Axle Load:
Vehicle Type Specified Condition
for Single Cab 7354 N (750 kgf, 1651 lbf)
for Double Cab 8336 N (850 kgf, 1874 lbf)


NOTICE:
·

Be sure that the vehicle is on a level surface before starting the procedure.

·

When placing the weights on the vehicle, first place the weights so that the total is approximately 60 kg (132 lb) more than the specification. Then remove weights as necessary to adjust the load.




c.
C331087N01
1.188,0.406 0.875,0.406 false 2.677,0.406 2.365,0.406 false 0.531,0.333 0.833,0.531 0.302,0.198 10 false SST 2.719,0.333 3.021,0.531 0.302,0.198 10 false SST

Install SST and bleed air from the brake system.

SST
09709-29018  


d.
C331088N01
0.656,0.417 0.385,0.417 false 2.635,0.417 2.365,0.417 false 0.073,0.344 0.396,0.531 0.323,0.188 10 false SST 2.688,0.333 2.99,0.531 0.302,0.198 10 false SST

Raise the front brake fluid pressure to 10000 kPa (107.6 kgf/cm2, 1450 psi) by depressing the brake pedal, and measure the rear brake fluid pressure.

Standard rear brake fluid pressure:

5260 +/-490 kPa (53.6 +/-5.0 kgf/cm2, 763 +/-71 psi)


HINT:
·

The pedal should not be depressed twice or released while raising the front brake fluid pressure.

·

Read the value of the rear brake fluid pressure after raising and holding the front fluid pressure for 2 seconds.



If necessary, adjust the load sensing proportioning valve.


Hide 47900 2.ADJUST LOAD SENSING PROPORTIONING VALVE ASSEMBLY

a.
C331089N01
0.781,2.052 0.938,2.25 0.156,0.198 10 false A

Adjust the length of the No. 2 load sensing spring shackle.

When the rear brake fluid pressure is below the standard pressure, lengthen length A.

When the rear brake fluid pressure is higher than the standard pressure, shorten length A.

Standard initial length (A):

120 mm (4.72 in.)


Standard length after Adjustment (A):

103 to 127 mm (4.06 to 5.00 in.)


HINT:

The rear brake fluid pressure changes as shown below by adjusting length A.


Standard pressure change:

Changes by 140 kPa (1.4 kgf/cm2, 20.3 psi) for every 1 mm (0.0394 in.) change in length A



b.
C331090

If the pressure cannot be adjusted by the No. 2 load sensing spring shackle, loosen the nuts and raise or lower the valve body.

When the pressure is below the standard pressure, lower the load sensing valve assembly.

When the pressure is higher than the standard pressure, raise the load sensing valve assembly.


c.

Tighten the nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Adjust the length of the No. 2 load sensing spring shackle again.

HINT:

If the length cannot be adjusted, check the load sensing valve assembly.



Hide 3.CHECK VALVE BODY

a.

Check that the master cylinder rear brake fluid pressure changes according to the rear wheel cylinder pressure.

Standard Pressure:
Master Cylinder Pressure Wheel Cylinder Pressure
2450 kPa (25 kgf/cm2, 355 psi) 1350 +/-200 kPa (13.8 +/-2 kgf/cm2, 196 +/-29 psi)
5880 kPa (60 kgf/cm2, 853 psi) 2210 +/-340 kPa (22.5 +/-3 kgf/cm2, 321 +/-49 psi)


If the result is not as specified, replace the load sensing valve assembly.