Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 4WD and Pre-Runner)
RM3250E _54 Brake _038046 BRAKE (FRONT) _0189600 FRONT BRAKE(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT BRAKE(for 4WD and Pre-Runner)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 04947 3.REMOVE FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake (Type A):

i.
C321907C01
1.042,0.438 0.75,0.438 true 1.771,1.615 1.458,1.188 1.458,1.188 1,1.188 true 1.25,1.948 0.635,1.948 true 2.323,1.24 2.667,1.396 2.667,1.396 2.896,1.396 true 0.542,0.375 0.75,0.542 0.208,0.167 10 true *1 2.938,1.323 3.177,1.49 0.24,0.167 10 true *2 0.771,1.125 0.99,1.281 0.219,0.156 10 true *3 0.406,1.885 0.615,2.052 0.208,0.167 10 true *1
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip and 2 disc brake pad guide pins.


ii.

Remove the front disc brake anti-rattle spring.

NOTICE:

The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




b.

for 15 inch Front Disc Brake (Type B):

i.
C334251C01
2.333,1.219 2.583,1.333 2.583,1.333 2.76,1.333 true 1.135,0.469 0.833,0.469 true 1.323,1.115 0.865,1.115 true 1.344,1.969 0.979,1.969 true 0.604,0.406 0.813,0.573 0.208,0.167 10 true *1 2.865,1.229 3.083,1.385 0.219,0.156 10 true *2 0.625,1.042 0.854,1.208 0.229,0.167 10 true *3 0.74,1.906 0.948,2.073 0.208,0.167 10 true *1
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




c.

for 16 inch Front Disc Brake (Type A):

i.
C321908C01
1.063,0.479 0.698,0.479 true 1.271,2.021 0.896,1.781 0.896,1.781 0.656,1.781 true 1.698,1.635 1.385,1.292 1.385,1.292 1.188,1.292 true 2.302,0.25 2.5,0.49 2.5,0.49 2.74,0.49 true 2.438,1.646 2.771,1.646 true 0.49,0.417 0.677,0.594 0.188,0.177 10 true *1 2.76,0.406 2.969,0.583 0.208,0.177 10 true *2 0.979,1.229 1.167,1.396 0.188,0.167 10 true *3 0.469,1.708 0.656,1.885 0.188,0.177 10 true *1 2.813,1.573 3.021,1.75 0.208,0.177 10 true *2
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips and 2 disc brake pad guide pins.


ii.

Remove the front disc brake anti-rattle spring.

NOTICE:

The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




d.

for 16 inch Front Disc Brake (Type B):

i.
C334252C01
1.104,0.427 0.76,0.427 true 1.323,2.021 0.885,2.021 true 1.302,1.125 0.885,1.125 true 2.438,1.688 2.781,1.688 false 2.292,0.229 2.49,0.406 2.49,0.406 2.688,0.406 true 0.51,0.365 0.76,0.521 0.25,0.156 10 true *1 2.719,0.344 2.917,0.531 0.198,0.188 10 true *2 0.677,1.031 0.875,1.188 0.198,0.156 10 true *3 0.688,1.948 0.875,2.104 0.188,0.156 10 true *1 2.833,1.615 3.104,1.781 0.271,0.167 10 true *2
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




Hide 04465 4.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the disc brake cylinder assembly LH.


Hide 04945 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims and 2 No. 2 anti-squeal shims from each pad.


Hide 47343A 6.DISCONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH

a.
C321909

Using a union nut wrench, disconnect the front No. 1 wheel cylinder tube LH from the disc brake cylinder assembly LH.


Hide 47750 7.REMOVE DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321910

Remove the 2 bolts and disc brake cylinder assembly LH.


Hide 43512 8.REMOVE FRONT DISC

a.
C321911C01
1.719,1.208 1.708,0.854 1.708,0.854 2.833,0.854 true 1.729,1.292 2.375,1.292 2.375,1.292 2.375,0.865 true 2.927,0.781 3.125,0.948 0.198,0.167 10 false *a
*a Matchmark


Put matchmarks on the front disc and axle hub.


b.

Remove the front disc.