Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 4WD and Pre-Runner)
RM3250E _54 Brake _038046 BRAKE (FRONT) _0189600 FRONT BRAKE(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT BRAKE(for 4WD and Pre-Runner)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47547B 1.TEMPORARILY INSTALL FRONT DISC BRAKE BLEEDER PLUG

a.

Temporarily install the front disc brake bleeder plug to the disc brake cylinder assembly LH.

HINT:

The front disc brake bleeder plug will be tightened to a torque specification in the "Bleed Brake Line" procedures.



Hide 31478B 2.INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.
C323741C01
0,0 0,0 false
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to 4 new piston seals.


b.

Install the 4 piston seals to the disc brake cylinder assembly LH.

NOTICE:

Securely install the piston seal into the groove of the disc brake cylinder assembly LH.



Hide 47731 4.INSTALL FRONT DISC BRAKE PISTON

a.
C321918C01
0.844,0.542 0.844,0.229 0.844,0.229 1.052,0.229 false 2.115,0.76 1.917,0.76 false 1.094,0.156 1.281,0.333 0.188,0.177 10 false *1 1.729,0.677 1.917,0.854 0.188,0.177 10 false *2
*1 Cylinder Boot
*2 Front Disc Brake Piston
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire inner circumference of 4 new cylinder boots, and the entire circumference of the top and bottom of the outer edge as shown in the illustration.


b.

Apply a light coat of lithium soap base glycol grease to the entire outer circumference of the 4 front disc brake pistons where they contact the cylinder boots and disc brake cylinder assembly LH.


c.

Install the 4 cylinder boots to the 4 front disc brake pistons.


d.

Install the 4 front disc brake pistons to the disc brake cylinder assembly LH.

NOTICE:

Do not forcibly install the front disc brake pistons to the disc brake cylinder assembly LH.



Hide 5.INSTALL CYLINDER BOOT

C321919C01
0.292,0.656 0.292,0.25 0.292,0.25 0.448,0.25 false 0.76,0.76 0.76,1.063 false 0.823,0.385 0.823,0.229 0.823,0.229 0.958,0.229 false 0.708,1.094 0.896,1.281 0.188,0.188 10 false *1 0.49,0.167 0.677,0.344 0.188,0.177 10 false *2 1.01,0.146 1.177,0.313 0.167,0.167 10 false *3
*1 Cylinder Boot
*2 Set Ring
*3 Front Disc Brake Piston


a.

Install one side of each of the 4 cylinder boots to the disc brake cylinder assembly LH.

NOTICE:

Install the cylinder boot securely into the grooves of the disc brake cylinder assembly LH and front disc brake piston.



b.

Using a screwdriver, install the 4 new set rings.

NOTICE:

Do not damage the cylinder boot.