Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › RELAY
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0189622 RELAY G

1KD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the body ECU removal/installation are shown below.

Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of body ECU Initialize automatic light control system Automatic light control system (Click here)

PROCEDURE

Hide 1.INSPECT EDU RELAY (EDU)

a.
A188757E05
2.708,0.573 2.833,0.208 2.833,0.208 3.052,0.208 true 2.135,0.563 2,0.208 2,0.208 1.771,0.208 true 2.646,1.115 3.063,1.115 true 2.646,1.604 3.063,1.604 true 1.646,0.125 1.802,0.323 0.156,0.198 10 false 1 3.115,0.135 3.271,0.333 0.156,0.198 10 false 2 3.125,1.031 3.281,1.229 0.156,0.198 10 false 5 3.115,1.51 3.271,1.708 0.156,0.198 10 false 3 0.313,1.25 0.469,1.448 0.156,0.198 10 false 1 0.313,0.771 0.469,0.969 0.156,0.198 10 false 3 1.323,0.771 1.479,0.969 0.156,0.198 10 false 5 1.323,1.271 1.479,1.469 0.156,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the EDU relay.


Hide 2.INSPECT IG2 RELAY (IG2)

a.
A188757E05
2.708,0.573 2.833,0.208 2.833,0.208 3.052,0.208 true 2.135,0.563 2,0.208 2,0.208 1.771,0.208 true 2.646,1.115 3.063,1.115 true 2.646,1.604 3.063,1.604 true 1.646,0.125 1.802,0.323 0.156,0.198 10 false 1 3.115,0.135 3.271,0.333 0.156,0.198 10 false 2 3.125,1.031 3.281,1.229 0.156,0.198 10 false 5 3.115,1.51 3.271,1.708 0.156,0.198 10 false 3 0.313,1.25 0.469,1.448 0.156,0.198 10 false 1 0.313,0.771 0.469,0.969 0.156,0.198 10 false 3 1.323,0.771 1.479,0.969 0.156,0.198 10 false 5 1.323,1.271 1.479,1.469 0.156,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the IG2 relay.


Hide 28300 3.INSPECT NO. 1 STARTER RELAY ASSEMBLY (ST)

Hide 28610 4.INSPECT GLOW PLUG RELAY (GLOW)

Hide 82730 5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

A349784C01
1.25,4.479 1.583,4.677 0.333,0.198 0.25,4.438 0.583,4.635 0.333,0.198 4.573,4.406 4.906,4.604 0.333,0.198 5.333,4.5 5.667,4.698 0.333,0.198 6,4.333 6.333,4.531 0.333,0.198 6.635,4.417 6.969,4.615 0.333,0.198 0.271,0.094 0.583,0.25 0.313,0.156 10 false *a 5.333,0.083 5.646,0.24 0.313,0.156 10 false *a 0.333,4.458 0.646,4.656 0.313,0.198 10 false 2K 1.333,4.49 1.646,4.688 0.313,0.198 10 false 2B 4.667,4.417 4.979,4.615 0.313,0.198 10 false 2J 5.417,4.51 5.729,4.708 0.313,0.198 10 false 2P 6.083,4.354 6.396,4.552 0.313,0.198 10 false 2N 6.719,4.438 7.031,4.635 0.313,0.198 10 false 2G
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


b.

Remove the main body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


c.

Inspect the EFI MAIN NO. 1 relay.

NOTICE:

Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and EFI NO. 1 fuses.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-1 - 2G-5 Battery voltage not applied to terminals 2P-9 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2P-9 and 2J-5 Below 1 Ω
2B-1 - 2K-3 Battery voltage not applied to terminals 2P-9 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2P-9 and 2J-5 Below 1 Ω
2B-1 - 2K-4 Battery voltage not applied to terminals 2P-9 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2P-9 and 2J-5 Below 1 Ω
2B-1 - 2N-1 Battery voltage not applied to terminals 2P-9 and 2J-5 10 kΩ or higher
Battery voltage applied to terminals 2P-9 and 2J-5 Below 1 Ω


If the result is not as specified, replace the instrument panel junction block assembly.



d.

Inspect the C/OPN NO. 1 relay.

NOTICE:

Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and IG2 NO. 1 fuses and EFI-MAIN NO. 1 relay.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-1 - 2K-5 Battery voltage applied to terminals 2P-9 and 2J-5 and battery voltage not applied to terminals 2G-1 and 2P-8 10 kΩ or higher
Battery voltage applied to terminals 2P-9 and 2J-5, and 2G-1 and 2P-8 Below 1 Ω


If the result is not as specified, replace the instrument panel junction block assembly.



e.

Install the main body ECU to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION


f.

Install the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION