Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER
RM3250E _51 Engine / Hybrid System _037993 1KD-FTV INTAKE / EXHAUST _0189637 EXHAUST MANIFOLD W/ TURBOCHARGER A

1KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 16027 1.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A211906C01
1.229,1.896 1.323,1.896 1.323,1.896 1.708,1.615 false 1.063,1.792 1.323,1.969 0.26,0.177 10 false *1
*1 New Gasket


Install a new gasket and No. 1 turbo water pipe sub-assembly with the 2 bolt and nuts.

Torque:
for bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.

Install a new gasket and the turbocharger sub-assembly with 3 new nuts to the exhaust manifold.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


b.
A272860C08
2.375,2.24 2.24,1.625 2.24,1.625 2.135,1.625 true 0.802,2.688 0.313,2.688 false 0.771,3.344 0.281,3.344 false 2.729,2.708 2.969,2.969 2.969,2.969 2.969,3.073 false 0.115,2.604 0.302,2.76 0.188,0.156 10 false *1 0.083,3.25 0.271,3.406 0.188,0.156 10 false *2 1.948,1.531 2.198,1.75 0.25,0.219 10 false *a 2.885,3.094 3.135,3.302 0.25,0.208 10 false *b 0.667,3.885 0.906,4.031 0.24,0.146 10 false x 2
*1 New Gasket
*2 Turbo Oil Inlet Pipe Sub-assembly
*a Narrow
*b Wide
V100135

Outside


Install a new gasket and the turbo oil inlet pipe sub-assembly with the 2 nuts, but only loosely install the nuts.

NOTICE:

The notch (wide part) of the gasket must face the engine.



c.
A272861C05
2.979,2.854 2.875,2.854 2.875,2.854 2.719,2.688 false 3,2.76 3.188,2.917 0.188,0.156 10 false *1
*1 Collar
V100136

Engine Side


Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head sub-assembly with 8 new nuts.

NOTICE:

Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



d.
A272862C08
0.26,2.271 0.26,2.583 false 0.76,2.729 1.115,2.729 false 0.24,1.781 0.302,1.396 0.302,1.396 0.417,1.396 false 1.823,2.542 2.229,2.542 false 1.979,3.948 1.729,3.615 1.729,3.615 1.615,3.615 false 0.427,1.313 0.615,1.469 0.188,0.156 10 false *1 0.552,2.635 0.74,2.792 0.188,0.156 10 false *2 0.156,2.594 0.344,2.75 0.188,0.156 10 false *3 1.417,3.531 1.698,3.719 0.281,0.188 10 false *a 1.719,2.24 1.865,2.385 0.146,0.146 10 false A 0.177,1.948 0.313,2.094 0.135,0.146 10 false B 2.24,2.448 2.427,2.604 0.188,0.156 10 false *1 1.021,3 1.26,3.146 0.24,0.146 10 false x 2
*1 New Gasket
*2 Turbo Oil Inlet Pipe Sub-assembly
*3 Union Bolt
*a Claw
V100135

Turbo Oil Inlet Pipe Side


Install a new gasket (labeled A) and the turbo oil inlet pipe sub-assembly with the 2 bolts, but only loosely install the bolts.

NOTICE:

The claws of the gasket must face the turbo oil inlet pipe sub-assembly.



e.

Install a new gasket (labeled B) and the turbo oil inlet pipe sub-assembly with the union bolt, but only loosely install the union bolt.


f.
A362450E01
2.854,1.146 3.042,1.333 0.188,0.188 10 true 6 2.854,0.063 3.042,0.25 0.188,0.188 10 true 5 2.021,0.052 2.208,0.24 0.188,0.188 10 true 1 1.094,0.052 1.281,0.24 0.188,0.188 10 true 3 0.458,0.052 0.646,0.24 0.188,0.188 10 true 7 0.198,1.292 0.385,1.479 0.188,0.188 10 true 8 1.177,1.323 1.365,1.51 0.188,0.188 10 true 4 1.865,1.313 2.052,1.5 0.188,0.188 10 true 2

Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Tighten the nuts in the order shown in the illustration.



g.

Tighten the 2 nuts and union bolt of the turbo oil inlet pipe sub-assembly, and the 2 bolts.

Torque:
for nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for union bolt : 26 N*m (265 kgf*cm, 19 ft.*lbf)
for bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:

Tighten the nut, union bolt and bolt in that order.



h.
A301829N01
2.094,1.729 2.25,1.927 0.156,0.198 10 false 3 2.333,1.625 2.49,1.823 0.156,0.198 10 false 2 2.375,1.365 2.604,1.604 0.229,0.24 10 false 1

Install the 2 bolts and the nut of the turbocharger stay in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17291 3.INSTALL TURBINE OUTLET ELBOW

a.

Install a new gasket and the turbine outlet elbow to the turbocharger sub-assembly with new 3 nuts.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 16284 4.INSTALL NO. 1 TURBO WATER HOSE

a.

Install the 2 No. 1 turbo water hoses to the No. 3 water by-pass pipe and cylinder block sub-assembly.


Hide 17167 5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Temporarily install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the bolt.


Hide 17271 6.INSTALL NO. 1 TURBO INSULATOR

a.

Temporarily install the No. 1 turbo insulator to the turbocharger sub-assembly with the 2 bolts.


b.

Tighten the bolt of the No. 1 exhaust manifold heat insulator, and the 2 bolts of the No. 1 turbo insulator.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17274 7.INSTALL COMPRESSOR INLET ELBOW

a.

Install a new gasket and the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the 2 connectors to the turbocharger sub-assembly.


c.

Attach the wire harness clamp.


Hide 12229 8.INSTALL PCV PIPE

a.

Connect the 2 PCV hoses to the cylinder head cover sub-assembly and compressor inlet elbow.


b.

Install the PCV pipe to the cylinder head sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 17701 9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the 3 wire harness clamps.


Hide 17801 10.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17705 11.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.

Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.


b.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Connect the mass air flow meter connector and attach the 2 wire harness clamps.


Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 53882F 13.INSTALL FRONT FENDER SEAL

a.

Install the front fender seal with new 6 clips.


Hide 53735B 14.INSTALL FRONT FENDER APRON SEAL UPPER

a.

Install the front fender apron seal upper with new 5 clips.


Hide 17940D 15.INSTALL INTERCOOLER ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51442 21.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 22.INSTALL NO. 1 ENGINE UNDER COVER