Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3250E _58 Vehicle Interior _038066 LIGHTING (INT) _0190028 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E317273E03
2.99,0.667 3.604,0.865 0.615,0.198 10 false SWIL 2.927,1.25 3.542,1.448 0.615,0.198 10 false AGND 3.458,0.677 4.073,0.875 0.615,0.198 10 false 9 3.469,1.229 4.083,1.427 0.615,0.198 10 false 6 1.906,1.792 2.521,1.99 0.615,0.198 10 false G81 1.906,1.958 3.792,2.292 1.885,0.333 10 false Engine Switch 5.01,1.823 5.625,2.021 0.615,0.198 10 false G69 5.01,1.99 6.844,2.344 1.833,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.281,0.656 5.896,0.854 0.615,0.198 10 false SWIL 5.302,1.219 5.917,1.417 0.615,0.198 10 false AGND 5.01,0.667 5.552,0.865 0.542,0.198 10 false 19 5,1.219 5.542,1.417 0.542,0.198 10 false 24 5.896,0.625 6.438,0.823 0.542,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Before performing the inspection, check that DTC B27B0 (Entry and Start System) is not output.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch illumination OFF or ON w/ Entry and Start System
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH


OK:

Engine switch illumination is normal.


Result:
Proceed to
OK
NG (for 1GR-FE)
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 2KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

NG (for 1GR-FE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 2KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the G81 engine switch connector.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-9 (SWIL) - G69-19 (SWIL) Always Below 1 Ω
G81-6 (AGND) - G69-24 (AGND) Always Below 1 Ω
G81-9 (SWIL) or G69-19 (SWIL) - Body ground Always 10 kΩ or higher
G81-6 (AGND) or G69-24 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR