Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM3250E _55 Steering _038051 STEERING GEAR / LINKAGE _0190439 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.SECURE STEERING WHEEL ASSEMBLY

a.
C327809

Secure the steering wheel assembly with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable sub-assembly.



Hide 3.REMOVE FRONT WHEELS

Hide 51410 4.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 2WD (w/ No. 1 Engine Under Cover Assembly))

Hide 51410 5.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER (for 2WD (w/ No. 1 Engine Under Cover))

Hide 51442 7.REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

Hide 51405D 8.REMOVE ENGINE UNDER BRACE SUB-ASSEMBLY (for 2WD)

a.

w/o No. 1 Engine Under Cover Assembly:

i.
C322689

Remove the 8 bolts and 2 engine under brace sub-assemblies.



b.

w/ No. 1 Engine Under Cover Assembly:

i.
C331231

Remove the 8 bolts and 2 engine under brace sub-assemblies.



Hide 45058A 9.REMOVE NO. 1 RACK BOOT PROTECTOR SUB-ASSEMBLY (for 2WD (w/ No. 1 Rack Boot Protector Sub-Assembly))

a.
C327810

Remove the 2 bolts and 2 rack boot protector sub-assemblies.


Hide 45047 10.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and nut.


b.
C322194C01
1.708,1.521 2.146,1.781 true 2.219,1.76 2.677,1.958 0.458,0.198 10 false SST 0.521,1.698 0.833,1.854 0.313,0.156 10 false *a 1.542,1.979 1.854,2.135 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, disconnect the tie rod end sub-assembly LH from the front axle hub assembly LH.

SST
09628-00011  


Hide 45046 11.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45219 12.DISCONNECT STEERING SLIDING YOKE

a.
C327811C01
2.667,1.677 3.125,1.563 3.125,1.563 2.729,1.542 true 3.146,1.458 3.375,1.729 0.229,0.271 10 false *a 1.177,0.115 1.417,0.344 0.24,0.229 10 true A 0.771,0.563 1.01,0.792 0.24,0.229 10 true B
*a Matchmark


Place matchmarks on the steering sliding yoke and No. 2 steering intermediate shaft sub-assembly.


b.

Loosen the bolt labeled A.


c.

Remove the bolt labeled B.


d.
C327812C01
0,0 0,0 false
V113147

Install in this Direction


Disconnect the steering sliding yoke from the No. 2 steering intermediate shaft sub-assembly.


Hide 45203 13.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C327813C01
1.729,1.177 2.469,1.708 2.469,1.708 1.833,1.073 true 2.49,1.719 2.802,1.917 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the No. 2 steering intermediate shaft sub-assembly and power steering link assembly.


b.
C327814C01
0,0 0,0 false
V113147

Install in this Direction


Remove the bolt and No. 2 steering intermediate shaft sub-assembly from the power steering link assembly.

NOTICE:

If the No. 2 steering intermediate shaft sub-assembly is struck, replace it with a new one.



Hide 41110F 14.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

Hide 15.REMOVE POWER STEERING LINK ASSEMBLY (for 2WD)

a.
C327815

Using a union nut wrench, loosen the flare nut and disconnect the pressure feed tube assembly.


b.
C327816

Remove the bolt and disconnect the pressure feed tube assembly bracket from the power steering link assembly.


c.
C327817

Slide the clip and disconnect the return hose.


d.
C327818

Using a union nut wrench, disconnect the steering gear outlet return tube.


e.
C327819C01
0,0 0,0 false
V113147

Remove in this Direction


Fix the 2 nuts in place and remove the 2 bolts and 2 washers. Then remove the power steering link assembly from the front suspension member.

NOTICE:

Never turn the nut. Be sure to turn the bolt.



Hide 16.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD and Pre-Runner)

a.
C327820

Using a union nut wrench, loosen the flare nut and disconnect the pressure feed tube assembly.


b.
C327821

Remove the bolt and disconnect the pressure feed tube assembly bracket from the power steering link assembly.


c.
C327822

Slide the clip and disconnect the return hose.


d.
C327823

Using a union nut wrench, disconnect the steering gear outlet return tube.


e.
C327824C01
0,0 0,0 false
V113147

Remove in this Direction


Fix the 2 nuts in place and remove the 2 bolts and 2 washers. Then remove the power steering link assembly from the front suspension member.

NOTICE:

Never turn the nut. Be sure to turn the bolt.