Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.ADJUST TIE ROD END SUB-ASSEMBLY
Adjust the tie rod end sub-assembly LH and RH so that distance A is within the specified ranges.
| for 2WD | 20 mm (0.7874 in.) or less |
| for 4WD and Pre-Runner | 17 mm (0.6693 in.) or less |
Make sure to tighten the nut in the alignment adjustment procedure.
Make sure that the boots are not twisted.
The values listed above are reference values.
The toe-in is adjusted in another step.
2.INSTALL POWER STEERING LINK ASSEMBLY (for 2WD)
Install the power steering link assembly with the 2 bolts, 2 washers and 2 nuts.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the steering gear outlet return tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
Install the hose with the clip.
Install the pressure feed tube assembly bracket to the power steering link assembly with the bolt.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, tighten the flare nut and connect the pressure feed tube assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
3.INSTALL POWER STEERING LINK ASSEMBLY (for 4WD and Pre-Runner)
Install the power steering link assembly with the 2 bolts, 2 washers and 2 nuts.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the steering gear outlet return tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
Install the hose with the clip.
Install the pressure feed tube assembly bracket to the power steering link assembly with the bolt.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, tighten the flare nut and connect the pressure feed tube assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
41110F
4.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
45203
5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
Align the matchmarks on the No. 2 steering intermediate shaft sub-assembly and power steering link assembly.
Install the bolt.
45219
6.CONNECT STEERING SLIDING YOKE
| *a | Matchmark |
|
Install in this Direction |
Align the matchmarks on the steering sliding yoke and No. 2 steering intermediate shaft, and connect the steering sliding yoke to the No. 2 steering intermediate shaft sub-assembly.
Install the bolt labeled B.
Tighten the bolt labeled A.
45047
7.CONNECT TIE ROD END SUB-ASSEMBLY LH
Connect the tie rod end sub-assembly LH to the front axle hub assembly with a new nut.
Install a new cotter pin.
If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.
45046
8.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45058A
9.INSTALL NO. 1 RACK BOOT PROTECTOR SUB-ASSEMBLY (for 2WD (w/ No. 1 Rack Boot Protector Sub-Assembly))
Install the 2 rack boot protector sub-assemblies with the 2 bolts.
51405D
10.INSTALL ENGINE UNDER BRACE SUB-ASSEMBLY (for 2WD)
Install the 2 engine under brace sub-assemblies with the 8 bolts.
51441
11.INSTALL NO. 1 ENGINE UNDER COVER (for 2WD (w/ No. 1 Engine Under Cover))
51442
12.INSTALL NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
51410
13.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 2WD (w/ No. 1 Engine Under Cover Assembly))
51410
14.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)
15.INSTALL FRONT WHEELS
16.ADD POWER STEERING FLUID
17.ADJUST POWER STEERING FLUID
18.CHECK FOR POWER STEERING FLUID LEAK
19.ADJUST FRONT WHEEL ALIGNMENT