Home › Engine / Hybrid System › 1TR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037997 1TR-FE ENGINE CONTROL _0191483 SFI SYSTEM J

1TR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN NO. 1 relay, closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A348508E02
1.188,0.896 3.094,1.365 1.906,0.469 10 false Ignition Switch Assembly 1.188,0.771 1.5,0.969 0.313,0.198 10 false G1 0.354,1.5 1.49,2.01 1.135,0.51 10 false STRG LOCK/AM2 NO. 1 1.438,0.573 1.896,0.771 0.458,0.198 10 false AM2 2.25,0.573 2.708,0.771 0.458,0.198 10 false IG2 1.292,0.344 1.448,0.542 0.156,0.198 10 false 4 2.573,0.354 2.729,0.552 0.156,0.198 10 false 3 3.26,2.125 4.635,2.323 1.375,0.198 10 false IG2 NO. 1 0.938,2.385 1.708,2.583 0.771,0.198 10 false J/B-B 0.406,3.24 1.479,3.438 1.073,0.198 10 false FL MAIN 0.531,4.427 1.604,4.625 1.073,0.198 10 false Battery 2.167,3.438 4.156,3.635 1.99,0.198 10 false EFI-MAIN NO.1 2.073,2.219 2.385,2.417 0.313,0.198 10 false 2B 2.063,1.99 2.219,2.188 0.156,0.198 10 false 1 3.031,4.021 5.177,4.219 2.146,0.198 10 false EFI-MAIN NO. 1 2.479,4.219 2.792,4.417 0.313,0.198 10 false 2J 2.771,4.208 2.927,4.406 0.156,0.198 10 false 5 4.271,3.729 4.583,3.927 0.313,0.198 10 false 2P 4.354,3.563 4.51,3.76 0.156,0.198 10 false 9 4.24,3.302 4.552,3.5 0.313,0.198 10 false 2G 4.344,3.115 4.5,3.313 0.156,0.198 10 false 5 2.906,4.458 4.51,5.052 1.604,0.594 10 false Instrument Panel Junction Block Assembly 5.854,1.875 6.469,2.073 0.615,0.198 10 false IGSW 5.844,2.375 6.302,2.573 0.458,0.198 10 false +B2 5.854,2.844 6.167,3.042 0.313,0.198 10 false +B 5.844,3.729 6.458,3.927 0.615,0.198 10 false MREL 5.865,4.271 6.177,4.469 0.313,0.198 10 false E1 5.479,1.979 5.938,2.177 0.458,0.198 10 false G46 5.615,1.792 5.771,1.99 0.156,0.198 10 false 8 5.479,2.385 5.938,2.583 0.458,0.198 10 false G46 5.615,2.198 5.771,2.396 0.156,0.198 10 false 2 5.49,2.854 5.948,3.052 0.458,0.198 10 false G46 5.625,2.656 5.781,2.854 0.156,0.198 10 false 1 5.49,3.729 5.948,3.927 0.458,0.198 10 false G45 5.635,3.542 5.792,3.74 0.156,0.198 10 false 6 5.49,4.271 5.948,4.469 0.458,0.198 10 false C52 5.625,4.083 5.781,4.281 0.156,0.198 10 false 3 6.156,4.656 6.615,4.854 0.458,0.198 10 false ECM 4.24,1.979 4.552,2.177 0.313,0.198 10 false 2G 4.333,1.792 4.49,1.99 0.156,0.198 10 false 2 2.875,1.604 3.188,1.802 0.313,0.198 10 false 2G 3.177,1.594 3.333,1.792 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM VOLTAGE)
a.
A356325C09
0.49,1.677 0.885,1.958 0.396,0.281 2.073,1.896 1.635,2.729 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.531,1.74 0.99,1.938 0.458,0.198 10 false G46 1.313,2.792 2.385,2.99 1.073,0.198 10 false 8(IGSW)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G46-8 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG B



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
A201293C08
0.448,1.063 0.854,1.333 0.406,0.271 0.552,1.104 0.865,1.302 0.313,0.198 10 false 2B 0.323,0.271 0.635,0.469 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2B-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EFI-MAIN NO. 1 RELAY
a.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-5 - G46-1 (+B) Always Below 1 Ω
2G-5 - G46-2 (+B2) Always Below 1 Ω
2P-9 - G45-6 (MREL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
a.
A348518C01
0.302,0.865 0.698,1.156 0.396,0.292 2.021,0.781 1.667,1.5 true 0.396,0.906 0.708,1.104 0.313,0.198 10 false G1 1.5,1.51 1.958,1.708 0.458,0.198 10 false AM2 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Ignition Switch)


Disconnect the ignition switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1TR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY