Home › Engine / Hybrid System › 1TR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037997 1TR-FE ENGINE CONTROL _0191483 SFI SYSTEM C

1TR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor for the intake camshaft (VV1 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction When one of the following conditions is met:
·

No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).

·

No camshaft position sensor signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).

·

A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).


·

Open or short in camshaft position sensor (for intake side) circuit

·

Camshaft position sensor (for intake side)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake side) circuit

·

Camshaft position sensor (for intake side)

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor (for intake side) circuit

·

Camshaft position sensor (for intake side)

·

ECM


Comes on DTC stored

A255508E19
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.698 0.427,0.865 0.323,0.167 10 CH1 0.125,1.479 0.448,1.646 0.323,0.167 10 CH2 0.052,0.865 0.427,1.01 0.375,0.146 10 (VV1) 0.063,1.625 0.458,1.771 0.396,0.146 10 (EV1) 3.042,0.813 3.385,0.958 0.344,0.146 10 GND 3.042,1.583 3.385,1.729 0.344,0.146 10 GND 1.25,1.885 2,2.063 0.75,0.177 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor signal (for intake side), and EV1 stands for the camshaft position sensor signal (for exhaust side).



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342 or P0343.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255253E63
1.083,1.927 1.417,2.073 0.333,0.146 10 false C65 1.083,2.083 4.219,2.281 3.135,0.198 10 false Camshaft Position Sensor (for Intake Side) 5.177,0.417 5.573,0.563 0.396,0.146 10 false VCV1 5.708,2.198 6.031,2.375 0.323,0.177 10 false C52 5.708,2.365 6.052,2.552 0.344,0.188 10 false ECM 4.927,0.417 5.208,0.604 0.281,0.188 10 false 21 4.938,0.969 5.146,1.167 0.208,0.198 10 false 23 4.927,1.49 5.177,1.656 0.25,0.167 10 false 22 2.646,0.396 2.771,0.563 0.125,0.167 10 false 3 2.646,0.948 2.75,1.125 0.104,0.177 10 false 1 2.646,1.49 2.75,1.635 0.104,0.146 10 false 2 2.323,0.406 2.542,0.583 0.219,0.177 10 false VC 2.188,0.948 2.615,1.125 0.427,0.177 10 false VVI+ 2.208,1.479 2.635,1.646 0.427,0.167 10 false VVI- 5.177,0.958 5.552,1.125 0.375,0.167 10 false VV1+ 5.177,1.49 5.552,1.656 0.375,0.167 10 false VV1- 1.615,0.896 1.75,1.063 0.135,0.167 10 false * 0.063,2.417 4.396,2.604 4.333,0.188 10 false *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE))
a.
A209301C41
0.167,1.156 0.646,1.458 0.479,0.302 1.969,1.271 2.385,1.729 true 0.188,0.292 0.5,0.49 0.313,0.198 10 false *a 0.271,1.229 0.729,1.427 0.458,0.198 10 false C65 2.333,1.771 2.646,1.969 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Intake Side))


Disconnect the camshaft position sensor (for intake side) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C65-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor (for intake side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-1 (VVI+) - C52-23 (VV1+) Always Below 1 Ω
C65-2 (VVI-) - C52-22 (VV1-) Always Below 1 Ω
C65-1 (VVI+) or C52-23 (VV1+) - Body ground Always 10 kΩ or higher
C65-2 (VVI-) or C52-22 (VV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE))
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the camshaft position sensor (for intake side) installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)
a.

Replace the camshaft position sensor (for intake side).

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

B

END

7.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)

NG

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE) - ECM)
a.

Disconnect the camshaft position sensor (for intake side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-3 (VC) - C52-21 (VCV1) Always Below 1 Ω
C65-3 (VC) or C52-21 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR