Home › Engine / Hybrid System › 1GD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER
RM3250E _51 Engine / Hybrid System _037976 1GD-FTV INTAKE / EXHAUST _0191561 EXHAUST MANIFOLD W/ TURBOCHARGER A

1GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the turbocharger sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization - (Click here)

CAUTION:
·
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 17362B 7.REMOVE NO. 2 AIR TUBE

Hide 16571C 8.REMOVE NO. 1 RADIATOR HOSE

Hide 44360 9.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 10.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 11.REMOVE RADIATOR RESERVOIR

Hide 16711 12.REMOVE FAN SHROUD

Hide 17705 13.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.
A344947

Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.


b.
A344948

Detach the 4 clips.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.


Hide 17801 14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.
A345134

Remove the air cleaner element sub-assembly from the air cleaner case.


Hide 17701 15.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A344949

Disconnect the 3 wire harness clamps.


b.
A344950

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 16.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 87120G 17.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

Hide 16279 18.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A352791

for Cold Specification Vehicles:

Slide the 2 clips and remove the water hose from the compressor inlet elbow and No. 3 water by-pass pipe.


b.
A359575C01
0.042,0.052 0.354,0.208 0.313,0.156 10 false *A 0.083,2.313 0.396,2.469 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Slide the 2 clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe.


c.

Remove the bolt and No. 3 water by-pass pipe.


Hide 12229 19.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

a.
A353393

Slide the 2 clips and disconnect the No. 20 water by-pass hose from the compressor inlet elbow and No. 3 water by-pass pipe.


b.

Slide the clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.


c.
A352793

Remove the bolt and disconnect the PCV pipe from the compression outlet elbow.


d.
A353394

Slide the 2 clips and remove the PCV pipe.


Hide 12261 20.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

a.
A344952

Slide the 2 clips.


b.

Slide the 2 clips, detach the clamp and remove the PCV hose.


Hide 16268 21.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 22.DISCONNECT TURBO WATER HOSE

a.
A359576C01
0.052,0.083 0.365,0.24 0.313,0.156 10 true *A 0.063,2.344 0.375,2.5 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Slide the 2 clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.


Hide 23.DISCONNECT BRACKET OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)

a.
A353408

Remove the bolt and disconnect the oil cooler tube bracket.


b.
A360492

w/ DPF:

Detach the 2 clamps and disconnect the wire harness.


c.
A344954

w/o DPF:

Remove the bolt and disconnect the wire harness.


Hide 24.DISCONNECT WIRE HARNESS CLAMP BRACKET (for Manual Transmission)

a.
A360491

w/ DPF:

Remove the bolt, detach the clamp and disconnect the wire harness.


b.
A344954

w/o DPF:

Remove the bolt and disconnect the wire harness.


Hide 87101 25.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

a.
A360493

Remove the bolt, detach the clamp and disconnect the wire harness.


b.
A360494

Remove the 4 bolts and the No. 1 viscous heater bracket sub-assembly.


Hide 17293 26.REMOVE TURBOCHARGER STAY

a.
A344955

Remove the 3 bolts, nut and the turbocharger stay.


Hide 15474 27.REMOVE TURBO OIL OUTLET PIPE

a.
A344956

Slide the 2 clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.


b.

Remove the 2 bolts and turbo oil outlet pipe and gasket.


Hide 15407 28.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A344957

Remove the union bolt and gasket.


b.
A344958

Remove the 2 nuts and the turbo oil inlet pipe sub-assembly.

NOTICE:
A344974E01
0.667,0.531 0.823,0.729 0.156,0.198 10 true A

Do not loosen the nut labeled A.



c.

Remove the gasket.


Hide 17201 29.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A359577C01
0.052,0.031 0.365,0.188 0.313,0.156 10 true *A 0.083,2.292 0.396,2.448 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Remove the 3 nuts and turbocharger sub-assembly.


b.

Remove the gasket from the exhaust manifold.


Hide 25601 30.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17141 31.REMOVE EXHAUST MANIFOLD

a.
A359578C01
0.083,0.094 0.396,0.25 0.313,0.156 10 true *A 0.094,2.354 0.406,2.51 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.


b.

Remove the gasket.


Hide 16027 32.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A359579C01
0.042,0.083 0.354,0.24 0.313,0.156 10 true *A 0.073,2.479 0.385,2.635 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the turbo water pipe sub-assembly.


b.

Remove the bolt.


c.
A344962

Remove the 2 nuts, turbo water pipe sub-assembly and gasket.


Hide 17274 33.REMOVE COMPRESSOR INLET ELBOW

a.
A359580C01
0.073,0.073 0.385,0.229 0.313,0.156 10 false *A 0.115,2.188 0.427,2.344 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Remove the 2 bolts and compressor inlet elbow stay.


b.
A359581C01
0.052,0.063 0.406,0.292 0.354,0.229 10 true *A 0.094,2.229 0.406,2.385 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Remove the 2 nuts and compressor inlet elbow from turbocharger sub-assembly.


c.
A359582C02
0.042,0.042 0.354,0.198 0.313,0.156 10 true *A 0.115,2.229 0.427,2.385 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow and gasket.


Hide 17275 34.REMOVE COMPRESSOR OUTLET ELBOW

a.
A359583C01
0.083,0.063 0.396,0.219 0.313,0.156 10 false *A 0.156,2.25 0.469,2.406 0.313,0.156 10 false *B
*A for Cold Specification Vehicles
*B except Cold Specification Vehicles


Remove the 2 nuts and compressor outlet elbow.


b.

Remove the gasket.


c.
A344967

except Cold Specification Vehicle:

Remove the bolt and hose clamp.


Hide 35.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A344968

Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.


b.
A344969

Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.


c.
A344970

Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.