The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
25051
1.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
51410
2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
3.DRAIN ENGINE COOLANT
4.DRAIN ENGINE OIL
17341F
5.REMOVE NO. 1 AIR HOSE
17344E
6.REMOVE NO. 4 AIR HOSE
17362B
7.REMOVE NO. 2 AIR TUBE
16571C
8.REMOVE NO. 1 RADIATOR HOSE
44360
9.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
44369A
10.REMOVE NO. 1 OIL RESERVOIR BRACKET
16470
11.REMOVE RADIATOR RESERVOIR
16711
12.REMOVE FAN SHROUD
17705
13.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.
Detach the 4 clips.
Loosen the hose clamp and remove the air cleaner cap sub-assembly with air cleaner hose.
17801
14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner element sub-assembly from the air cleaner case.
17701
15.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Disconnect the 3 wire harness clamps.
Remove the 3 bolts and air cleaner case sub-assembly.
16.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)
87120G
17.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)
16279
18.REMOVE NO. 3 WATER BY-PASS PIPE
for Cold Specification Vehicles:
Slide the 2 clips and remove the water hose from the compressor inlet elbow and No. 3 water by-pass pipe.
| *A | for Cold Specification Vehicles |
| *B | except Cold Specification Vehicles |
Slide the 2 clips and disconnect the 2 water hoses from the oil cooler assembly and No. 2 water by-pass pipe.
Remove the bolt and No. 3 water by-pass pipe.
12229
19.REMOVE PCV PIPE (for Cold Area Specification Vehicles)
Slide the 2 clips and disconnect the No. 20 water by-pass hose from the compressor inlet elbow and No. 3 water by-pass pipe.
Slide the clip and disconnect the No. 19 water by-pass hose from the compressor inlet elbow.
Remove the bolt and disconnect the PCV pipe from the compression outlet elbow.
Slide the 2 clips and remove the PCV pipe.
12261
20.REMOVE PCV HOSE (except Cold Area Specification Vehicles)
Slide the 2 clips.
Slide the 2 clips, detach the clamp and remove the PCV hose.
16268
21.REMOVE NO. 1 WATER BY-PASS PIPE
16284
22.DISCONNECT TURBO WATER HOSE
| *A | for Cold Specification Vehicles |
| *B | except Cold Specification Vehicles |
Slide the 2 clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the water outlet sub-assembly and water pump assembly.
23.DISCONNECT BRACKET OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)
Remove the bolt and disconnect the oil cooler tube bracket.
w/ DPF:
Detach the 2 clamps and disconnect the wire harness.
w/o DPF:
Remove the bolt and disconnect the wire harness.
24.DISCONNECT WIRE HARNESS CLAMP BRACKET (for Manual Transmission)
w/ DPF:
Remove the bolt, detach the clamp and disconnect the wire harness.
w/o DPF:
Remove the bolt and disconnect the wire harness.
87101
25.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
Remove the bolt, detach the clamp and disconnect the wire harness.
Remove the 4 bolts and the No. 1 viscous heater bracket sub-assembly.
17293
26.REMOVE TURBOCHARGER STAY
Remove the 3 bolts, nut and the turbocharger stay.
15474
27.REMOVE TURBO OIL OUTLET PIPE
Slide the 2 clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.
Remove the 2 bolts and turbo oil outlet pipe and gasket.
15407
28.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
Remove the union bolt and gasket.
Remove the 2 nuts and the turbo oil inlet pipe sub-assembly.
Do not loosen the nut labeled A.
Remove the gasket.
17201
29.REMOVE TURBOCHARGER SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 3 nuts and turbocharger sub-assembly.
Remove the gasket from the exhaust manifold.
30.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)
25601
31.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)
17141
32.REMOVE EXHAUST MANIFOLD
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.
Remove the gasket.
16027
33.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Slide the 2 hose clips and disconnect the No. 1 turbo water hose and No. 2 turbo water hose from the turbo water pipe sub-assembly.
Remove the bolt.
Remove the 2 nuts, turbo water pipe sub-assembly and gasket.
17274
34.REMOVE COMPRESSOR INLET ELBOW
Remove the 2 bolts and compressor inlet elbow stay.
| *A | for Cold Specification Vehicles |
| *B | except Cold Specification Vehicles |
Remove the 2 nuts and compressor inlet elbow from turbocharger sub-assembly.
| *A | for Cold Specification Vehicles |
| *B | except Cold Specification Vehicles |
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration together with the compressor inlet elbow and gasket.
17275
35.REMOVE COMPRESSOR OUTLET ELBOW
| *A | for Cold Specification Vehicles |
| *B | except Cold Specification Vehicles |
Remove the 2 nuts and compressor outlet elbow.
Remove the gasket.
except Cold Specification Vehicle:
Remove the bolt and hose clamp.
36.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E5 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E8 "TORX" socket wrench, remove the 4 stud bolts shown in the illustration.
Using an E10 "TORX" socket wrench, remove the 3 stud bolts shown in the illustration.