Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3250E _59 Vehicle Exterior _038076 WIPER / WASHER _0192113 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

a.
B407797C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, detach the claw and remove the front wiper arm head cap.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for both front wiper arm head caps.




Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
B407798

Remove the nut and front wiper arm and blade assembly LH.


Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
B407799

Remove the nut and front wiper arm and blade assembly RH.


Hide 53886G 4.REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY LH

a.
B407800C01
1.427,0.688 1.99,0.479 false 2.063,0.365 2.375,0.521 0.313,0.156 10 false *a
*a Claw A


Detach the clip and disconnect the hood to cowl top seal from the fender apron mudguard seal sub-assembly LH.


b.

Detach claw A by hand from the bottom of the fender apron mudguard seal sub-assembly LH.


c.

Detach the claw and clip and remove the fender apron mudguard seal sub-assembly LH.


Hide 53885G 5.REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 53389B 6.REMOVE HOOD TO FRONT FENDER SEAL LH (w/ Seal)

a.
B407801

Detach the claw and remove the hood to front fender seal LH.


Hide 53388D 7.REMOVE HOOD TO FRONT FENDER SEAL RH (w/ Seal)

HINT:

Use the same procedure described for the LH side.


Hide 53867H 8.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

a.
B407802C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the claw and guide and remove the front fender to cowl side seal LH as shown in the illustration.


Hide 53866J 9.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 55781E 10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
B407803

Remove the 2 clips.


b.
B407804C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw.


c.
B407805C01
0,0 0,0 false
V113147

Remove in this Direction


Pull the cowl top ventilator louver sub-assembly as shown in the illustration to detach the guide and remove the cowl top ventilator louver sub-assembly.


Hide 53383 11.REMOVE HOOD TO COWL TOP SEAL

a.
B407806

Detach the claw and clip and remove the hood to cowl top seal.


Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

NOTICE:

Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.


a.
B407759C02
1.948,2.99 1.427,3.135 true 1.25,3.073 1.469,3.24 0.219,0.167 10 true *1
*1 Motor Grommet
V100135

Connector
V100136

Bolt
V113147

Remove in this Direction


Disconnect the connector.


b.

Remove the 2 bolts.


c.

Detach the motor grommet as shown in the illustration and remove the windshield wiper motor and link assembly.


Hide 85110 13.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B407760C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a screwdriver, disconnect the No. 1 windshield wiper link rod from the front wiper crank pivot.

HINT:

Tape the screwdriver tip before use.



b.
B407761

Using a T30 "TORX" socket wrench, remove the 2 bolts and windshield wiper motor assembly.