Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2015.06–2016.03
RM3250E _59 Vehicle Exterior _038076 WIPER / WASHER _0192115 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.

Check the front wiper intermittent operation.

i.
E322150C01
2.781,1.135 3.229,1.344 0.448,0.208 0.219,1.135 0.667,1.344 0.448,0.208 1.25,1.156 1.188,0.729 true 2.406,1.833 2.354,1.5 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.875,1.167 3.333,1.365 0.458,0.198 10 false G18 0.313,1.167 0.771,1.365 0.458,0.198 10 false G19 1.094,0.531 1.406,0.729 0.313,0.198 10 false +1 2.333,1.865 2.646,2.063 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G19-3 (+1) and a negative (-) lead to terminal G18-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper and check the voltage between terminals G19-3 (+1) and G18-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493E71
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.354,0.885 2.604,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.865,1.177 1.792,0.677 10 false Voltage between terminals G19-3 (+1) and G18-4 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 second 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW: 0.083,0.042 2.375,0.24 2.292,0.198 12 false w/ Adjust Ring:

E294527E13
0.125,0.083 1.583,0.344 1.458,0.26 12 false w/o Adjust Ring: 0.135,0.5 1.958,0.896 1.823,0.396 10 false Voltage between terminals G19-3 (+1) and G18-4 (EW): 0.823,1.365 1.948,1.615 1.125,0.25 10 false Wiper Operation: 4.677,1 5.927,1.219 1.25,0.219 10 false 3.3 +/-1 second 3.833,1.396 4.26,1.656 0.427,0.26 10 false Stop 4.479,1.396 4.906,1.656 0.427,0.26 10 false Start 2.698,0.438 3.542,0.677 0.844,0.24 10 false 11 to 14 V 3.146,0.865 3.552,1.094 0.406,0.229 10 false 0 V

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation.

i.
E322150C02
2.781,1.135 3.229,1.344 0.448,0.208 0.219,1.135 0.667,1.344 0.448,0.208 1.906,1.823 1.99,1.51 true 2.406,1.833 2.354,1.5 true 0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 2.875,1.167 3.333,1.365 0.458,0.198 10 false G18 0.313,1.167 0.771,1.365 0.458,0.198 10 false G19 1.802,1.865 2.115,2.063 0.313,0.198 10 false WF 2.333,1.865 2.646,2.063 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G18-4 (WF) and a negative (-) lead to terminal G18-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals G18-4 (WF) and G18-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E65
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.875 2.854,1.229 1.875,0.354 10 false Voltage between terminals 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On 0.969,1.063 4.948,1.26 3.979,0.198 10 false G18-7 (WF) and G18-4 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.

Check the front wiper intermittent operation (w/ Intermittent function).

i.
E288057C18
0.167,1.083 0.667,1.333 0.5,0.25 2.698,1.073 3.198,1.323 0.5,0.25 1.031,1.479 0.823,1.833 true 2.177,1.167 2.375,0.625 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.292,1.115 0.75,1.313 0.458,0.198 10 false G18 2.313,0.438 2.604,0.604 0.292,0.167 10 false +1 0.688,1.896 0.979,2.063 0.292,0.167 10 false EW 2.823,1.115 3.281,1.313 0.458,0.198 10 false G19
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G19-2 (+1) and a negative (-) lead to terminal G18-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper and check the voltage between terminals G19-2 (+1) and G18-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493E68
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.083,0.5 1.875,0.885 1.792,0.385 10 false Voltage between terminals G19-2 (+1) and G18-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/-1 second 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/-5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW: 0.104,0.083 1.302,0.323 1.198,0.24 12 false w/ Adjust Ring:

E294527E12
0.125,0.094 1.583,0.354 1.458,0.26 12 false w/o Adjust Ring: 0.135,0.5 1.958,0.896 1.823,0.396 10 false Voltage between terminals G19-2 (+1) and G18-7 (EW): 0.823,1.365 1.948,1.615 1.125,0.25 10 false Wiper Operation: 4.677,1 5.927,1.219 1.25,0.219 10 false 3.3 +/-1 second 3.833,1.396 4.26,1.656 0.427,0.26 10 false Stop 4.479,1.396 4.906,1.656 0.427,0.26 10 false Start 2.698,0.438 3.542,0.677 0.844,0.24 10 false 11 to 14 V 3.115,0.875 3.521,1.104 0.406,0.229 10 false 0 V

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation.

i.
E288057C19
0.167,1.083 0.667,1.333 0.5,0.25 2.698,1.073 3.198,1.323 0.5,0.25 1.031,1.479 0.844,1.833 true 1.5,1.479 1.729,1.854 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.292,1.125 0.75,1.323 0.458,0.198 10 false G18 1.656,1.896 1.948,2.063 0.292,0.167 10 false WF 0.729,1.875 1.021,2.042 0.292,0.167 10 false EW 2.823,1.115 3.281,1.313 0.458,0.198 10 false G19
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G18-4 (WF) and a negative (-) lead to terminal G18-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals G18-4 (WF) and G18-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E66
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.875 2.854,1.229 1.875,0.354 10 false Voltage between terminals 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On 0.969,1.063 4.948,1.26 3.979,0.198 10 false G18-4 (WF) and G18-7 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.