Home › Engine / Hybrid System › 2GD-FTV EMISSION CONTROL › EGR VALVE › 2015.06–2016.03
RM3250E _51 Engine / Hybrid System _038008 2GD-FTV EMISSION CONTROL _0192537 EGR VALVE A

2GD-FTV EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of diesel throttle body assembly Perform initialization - (Click here)
Replacement of electric EGR control valve assembly Perform initialization - (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 26100G 2.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 3.REMOVE NO. 2 WATER BY-PASS PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.

w/ Heater:

i.
A358235

w/ DPF:

Slide the clamp and disconnect the No. 18 water by-pass hose from the EGR pipe with cooler sub-assembly.


ii.
A358282C01
0.01,1.615 0.24,1.781 0.229,0.167 10 true *1 0.208,1.615 0.438,1.781 0.229,0.167 10 true *2 0.042,0.667 0.271,0.833 0.229,0.167 10 true *3 2.927,0.698 3.156,0.865 0.229,0.167 10 true *4 2.313,2.51 2.542,2.677 0.229,0.167 10 true *5 3.198,0.781 3.427,0.948 0.229,0.167 10 true *4
*1 Water Hose Sub-assembly
*2 No. 13 Water By-pass Hose
*3 No. 15 Water By-pass Hose
*4 Heater Hose
*5 No. 16 Water By-pass Hose


w/ Viscous Heater:

Slide the clamp and disconnect the No. 2 water by-pass pipe from the water hose sub-assembly.


iii.

w/o Viscous Heater:

Slide the clamp and disconnect the No. 2 water by-pass pipe from the No. 13 water by-pass hose.


iv.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


v.

Slide the 2 clamps and disconnect the 2 heater hoses from the No. 2 water by-pass pipe.


vi.

Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.


vii.

Remove the 4 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket.



b.
A343884C01
0.042,0.26 0.24,0.427 0.198,0.167 10 true *1 2.125,1.927 2.313,2.094 0.188,0.167 10 true *2
*1 No. 15 Water By-pass Hose
*2 No. 16 Water By-pass Hose


w/o Heater:

i.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


ii.

Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.


iii.

Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket.



Hide 23265C 4.REMOVE GAS FILTER

a.
A343885

Disconnect the 2 vacuum hoses from the turbo pressure sensor and intake manifold.


b.

Remove the gas filter from the gas filter bracket.


Hide 89421C 5.REMOVE TURBO PRESSURE SENSOR

a.
A343886

Disconnect the connector from the turbo pressure sensor.


b.

Remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


Hide 44763C 6.REMOVE NO. 2 HOSE TO HOSE TUBE

a.
A343888

Slide the clamp to disconnect the union to connector tube hose from the No. 1 hose to hose tube.


b.

Slide the clamp to disconnect the union to check valve hose from the vacuum pump assembly.


c.

Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.


Hide 12632 7.REMOVE NO. 2 ENGINE COVER BRACKET

a.
A343887

Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly.


Hide 23300 8.DISCONNECT FUEL FILTER ASSEMBLY

a.
A339642N01
3.083,1 3.292,1.188 0.208,0.188 10 true 1 2.802,1.646 3.01,1.833 0.208,0.188 10 true 2

Disconnect the clamp and slide the lead wire as shown in the illustration to remove it.


b.
A344450

Disconnect the fuel filter assembly from the fuel filter support.


Hide 82121 9.DISCONNECT ENGINE WIRE

a.
A343889

Detach the 2 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.


b.
A358281

w/ DPF:

i.

Disconnect the connector from the differential pressure sensor.


ii.

Disconnect the 3 connectors from the 3 exhaust gas temperature sensors


iii.

Disconnect the connector from the exhaust fuel addition injector assembly.


iv.

Disconnect the connector from the camshaft position sensor.


v.

Disconnect the 4 connectors from the 4 injector assemblies.


vi.

Disconnect the connector from the electric EGR control valve assembly.


vii.

Disconnect the connector from the glow plug connector.


viii.

Disconnect the connector from the sensor wire of common rail assembly.


ix.

Detach the 2 clamps and remove the bolt.



c.
A343891

w/o DPF:

i.

Disconnect the connector from the camshaft position sensor.


ii.

Disconnect the 4 connectors from the 4 injector assemblies.


iii.

Disconnect the connector from the electric EGR control valve assembly.


iv.

Disconnect the connector from the glow plug connector.


v.

Disconnect the connector from the sensor wire of common rail assembly.


vi.

Detach the clamp and remove the bolt.



d.
A343893

Detach the clamp and disconnect the connector from the power steering oil pressure switch.


e.

Detach the clamp and remove the bolt.


f.

Disconnect the connector from the vacuum control valve set.


Hide 25625 10.REMOVE EGR VALVE BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343894

Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


Hide 25612 11.REMOVE NO. 2 EGR PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343895

Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.


b.

Remove the 2 gaskets.


Hide 25800 12.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343896

Detach the clamp and disconnect the connector from the common rail assembly.


b.
A343897

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


c.

Remove the 2 bolts and electric EGR control valve assembly.


d.

Remove the gasket.


Hide 16206B 13.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343898

Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A343899

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.


Hide 16209 14.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A344448

w/ DPF:

Slide the clamp and disconnect the No. 17 water by-pass hose from the No. 1 EGR pipe sub-assembly.


b.
A358236C01
0.094,0.125 0.323,0.313 0.229,0.188 10 true *A 0.135,2.521 0.365,2.708 0.229,0.188 10 true *B
*A w/ DPF
*B w/o DPF


Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.


c.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


d.

Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 15.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A358237

Remove the bolt and disconnect the EGR pipe with cooler sub-assembly from the vacuum transmitting pipe sub-assembly.


b.
A358238

Remove the 4 nuts and the EGR pipe with cooler sub-assembly from the exhaust manifold and EGR valve adapter.


c.

Remove the 2 gaskets.


d.
A352184

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25601 16.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A352183

Remove the bolt and disconnect the No. 1 EGR pipe sub-assembly from the vacuum transmitting pipe sub-assembly.


b.
A343901

Remove the 4 nuts and the No. 1 EGR pipe sub-assembly from the exhaust manifold and EGR valve adapter.


c.

Remove the 2 gaskets.


d.
A352184

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 17.REMOVE VACUUM CONTROL VALVE SET

a.
A343903

Remove the bolt and engine wire bracket.


b.
A343904

Disconnect the 2 vacuum hoses from the No. 2 vacuum transmitting pipe sub-assembly and No. 2 EGR valve assembly.


c.
A343905

Remove the 2 bolts and vacuum control valve set from the intake manifold.


Hide 18.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343906

Remove the 4 bolts and No. 1 EGR cooler and No. 2 EGR valve assembly from the intake manifold.


Hide 25624 19.REMOVE EGR VALVE ADAPTER

a.
A343907

Remove the 2 bolts and EGR valve adapter from the No. 2 EGR valve assembly.


b.

Remove the gasket.


Hide 25630 20.REMOVE NO. 2 EGR VALVE ASSEMBLY

a.
A343908

Remove the 4 bolts and No. 2 EGR valve assembly from the No. 1 EGR cooler.


b.

Remove the gasket.


c.
A343909

Using an E8 "TORX" socket wrench, remove the 4 stud bolts from the No. 2 EGR valve assembly.