To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.
The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTING SYSTEM>PRECAUTION
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
28800
3.INSPECT BATTERY
16620
4.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
17801
5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case.
Check that the air cleaner filter element sub-assembly is not excessively dirty.
If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.
If cleaning the air cleaner filter element sub-assembly. blow compressed air to clean it.
Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.
When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.
When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.
Reinstall the air cleaner filter element sub-assembly to the air cleaner case.
6.INSPECT ENGINE IDLE SPEED
Warm up and stop the engine.
When using the GTS:
For more information about the GTS, refer to its operator's manual.
If the GTS is not available, use a tachometer as a substitute.
Connect the GTS to the DLC3.
Start the engine and idle it.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
| *a | Front view of DLC3 |
When not using the GTS:
Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
Start the engine and idle it.
Inspect the engine idle speed.
700 to 800 rpm
Turn all the electrical systems and A/C off.
When checking the idle speed, move the shift lever to neutral.
Turn the ignition switch off.
Disconnect the GTS or tachometer tester probe from the DLC3.
7.INSPECT MAXIMUM ENGINE SPEED
Start the engine.
Fully depress the accelerator pedal.
Check the maximum engine speed.
4450 to 4750 rpm
8.INSPECT CYLINDER COMPRESSION PRESSURE
Measure the compression pressure if the engine power is insufficient, oil is consumed excessively and/or fuel economy is poor.
Remove the 4 glow plug assemblies.
Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG>REMOVAL
Disconnect the 4 connectors from the 4 injector assemblies.
Crank the engine to expel soot and other foreign matter from the inside of the cylinder.
| *a | SST (Gauge Assembly) |
| *b | SST (Attachment H) |
Measure the compression pressure.
Install SST (attachment) to the glow plug hole.
Connect SST (compression gauge) to SST (attachment).
Measure the compression pressure while cranking the engine.
Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
Perform the procedure above for each cylinder.
2700 kPa (27.5 kgf/cm2, 392 psi) or higher
2200 kPa (22.4 kgf/cm2, 319 psi)
500 kPa (5.1 kgf/cm2, 73 psi) or less
This measurement must be done in as short a time as possible.
If the compression in one or more cylinders is low, add a small amount of engine oil into the glow plug hole. Then, repeat the procedure above for the low-compression cylinder(s).
If poor compression improves after adding engine oil, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure remains low, a valve may be stuck or seated improperly, or pressure may be dropping due to leakage through the gasket.
Remove SST (attachment and compression gauge).
Connect the 4 connectors to the 4 injector assemblies.
Install the 4 glow plug assemblies.
Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG>INSTALLATION