Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › VALVE CLEARANCE
RM3250E _51 Engine / Hybrid System _037989 1KD-FTV ENGINE MECHANICAL _0193241 VALVE CLEARANCE N

1KD-FTV ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


CAUTION / NOTICE / HINT

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



HINT:

The injector assemblies do not need to be removed when inspecting the valve clearance.


PROCEDURE

Hide 11201 1.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 2.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A352016C01
2.667,0.75 2.667,1.167 true 2.458,0.823 2.458,0.99 2.458,0.99 2.656,0.99 true 2.615,1.156 2.844,1.354 0.229,0.198 10 true *a
*a Matchmark


Align the matchmarks of the crankshaft pulley and timing gear cover by rotating the crankshaft clockwise.

HINT:

Make sure that both cam lobes (intake side and exhaust side) of the No. 1 cylinder face upward.



Hide 3.INSPECT VALVE CLEARANCE

a.
A352017C01
1,1.531 1.135,1.698 0.135,0.167 10 true 1 1.177,1.531 1.313,1.698 0.135,0.167 10 true 1 1.177,0.333 1.313,0.5 0.135,0.167 10 true 1 1,0.333 1.135,0.5 0.135,0.167 10 true 1 1.427,1.521 1.563,1.688 0.135,0.167 10 true 2 1.583,1.521 1.719,1.688 0.135,0.167 10 true 2 1.844,0.333 1.979,0.5 0.135,0.167 10 true 3 2.031,0.333 2.167,0.5 0.135,0.167 10 true 3 0.833,0.167 1,0.333 0.167,0.167 10 true *a 2.833,0.792 3,0.958 0.167,0.167 10 true *b 2.833,1.042 3,1.208 0.167,0.167 10 true *c
*a Front
*b Exhaust
*c Intake


Check only the valves indicated.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.2 to 0.3 mm (0.00787 to 0.0118 in.)
Exhaust 0.35 to 0.45 mm (0.0138 to 0.0177 in.)


Write down any valve clearance measurements that are not within the specified range. These measurements will be used later to determine the size of the adjustment valve lifter to be installed.



b.

Turn the crankshaft 360° to set the No. 4 cylinder to TDC/compression.


c.
A352018C01
0.823,0.167 1.042,0.333 0.219,0.167 10 false *a 2.813,0.802 3.031,0.969 0.219,0.167 10 false *b 2.813,1.021 3.031,1.188 0.219,0.167 10 false *c 1.438,0.333 1.563,0.5 0.125,0.167 10 true 2 1.594,0.333 1.719,0.5 0.125,0.167 10 true 2 2.281,0.333 2.406,0.5 0.125,0.167 10 true 4 2.438,0.333 2.563,0.5 0.125,0.167 10 true 4 1.844,1.5 1.969,1.667 0.125,0.167 10 true 3 2.021,1.5 2.146,1.667 0.125,0.167 10 true 3 2.281,1.5 2.406,1.667 0.125,0.167 10 true 4 2.438,1.5 2.563,1.667 0.125,0.167 10 true 4
*a Front
*b Exhaust
*c Intake


Check only the valves indicated.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.2 to 0.3 mm (0.00787 to 0.0118 in.)
Exhaust 0.35 to 0.45 mm (0.0138 to 0.0177 in.)


Write down any valve clearance measurements that are not within the specified range. These measurements will be used later to determine the size of the adjustment valve lifter to be installed.



Hide 4.ADJUST VALVE CLEARANCE

a.

Remove the camshaft sub-assemblies.

Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Remove the valve lifters.


c.
A352019

Using a micrometer, measure the thickness of the removed valve lifter.


d.

Calculate the thickness of a new lifter so that the valve clearance is within the specified range.

A B C
New valve lifter thickness Used valve lifter thickness Measured valve clearance

New valve lifter thickness:

Intake: A = B + (C - 0.25 mm (0.00984 in.))

Exhaust: A = B + (C - 0.40 mm (0.0157 in.))



e.

Select a new valve lifter with a thickness as close as possible to the calculated values.

HINT:

Valve lifters are available in 35 sizes in increments of 0.02 mm (0.000787 in.), from 5.06 mm (0.199 in.) to 5.74 mm (0.226 in.).



f.

Install the selected valve lifter.

A247217C14
3.271,0.104 3.469,0.313 0.198,0.208 10 false *a 0.656,0.646 0.854,0.854 0.198,0.208 10 false *b 0.479,1.271 0.677,1.479 0.198,0.208 10 false *c
*a Valve Lifter Selection Chart (Intake) *b Measured clearance mm (in.)
*c Installed lifter thickness mm (in.) - -


Standard intake valve clearance (Cold):

0.2 to 0.3 mm (0.00787 to 0.0118 in.)


EXAMPLE:

A 5.25 mm (0.207 in.) lifter is installed, and the measured clearance is 0.4 mm (0.0157 in.). Replace the 5.25 mm (0.207 in.) lifter with a No. 40 lifter.


New Lifter Thickness:
Lifter No. Specified Condition Lifter No. Specified Condition Lifter No. Specified Condition
06 5.06 mm (0.1992 in.) 30 5.30 mm (0.2087 in.) 54 5.54 mm (0.2181 in.)
08 5.08 mm (0.2000 in.) 32 5.32 mm (0.2094 in.) 56 5.56 mm (0.2189 in.)
10 5.10 mm (0.2008 in.) 34 5.34 mm (0.2102 in.) 58 5.58 mm (0.2197 in.)
12 5.12 mm (0.2016 in.) 36 5.36 mm (0.2110 in.) 60 5.60 mm (0.2205 in.)
14 5.14 mm (0.2024 in.) 38 5.38 mm (0.2118 in.) 62 5.62 mm (0.2213 in.)
16 5.16 mm (0.2031 in.) 40 5.40 mm (0.2126 in.) 64 5.64 mm (0.2220 in.)
18 5.18 mm (0.2039 in.) 42 5.42 mm (0.2134 in.) 66 5.66 mm (0.2228 in.)
20 5.20 mm (0.2047 in.) 44 5.44 mm (0.2142 in.) 68 5.68 mm (0.2236 in.)
22 5.22 mm (0.2055 in.) 46 5.46 mm (0.2150 in.) 70 5.70 mm (0.2244 in.)
24 5.24 mm (0.2063 in.) 48 5.48 mm (0.2157 in.) 72 5.72 mm (0.2252 in.)
26 5.26 mm (0.2071 in.) 50 5.50 mm (0.2165 in.) 74 5.74 mm (0.2260 in.)
28 5.28 mm (0.2079 in.) 52 5.52 mm (0.2173 in.) - -


A247219C13
3.344,0.104 3.542,0.313 0.198,0.208 10 false *a 0.698,0.677 0.896,0.885 0.198,0.208 10 false *b 0.448,1.24 0.646,1.448 0.198,0.208 10 false *c
*a Valve Lifter Selection Chart (Exhaust) *b Measured clearance mm (in.)
*c Installed lifter thickness mm (in.) - -


Standard exhaust valve clearance (Cold):

0.35 to 0.45 mm (0.0138 to 0.0177 in.)


EXAMPLE:

A 5.34 mm (0.210 in.) lifter is installed, and the measured clearance is 0.48 mm (0.0189 in.). Replace the 5.34 mm (0.210 in.) lifter with a No. 42 lifter.


New Lifter Thickness:
Lifter No. Specified Condition Lifter No. Specified Condition Lifter No. Specified Condition
06 5.06 mm (0.1992 in.) 30 5.30 mm (0.2087 in.) 54 5.54 mm (0.2181 in.)
08 5.08 mm (0.2000 in.) 32 5.32 mm (0.2094 in.) 56 5.56 mm (0.2189 in.)
10 5.10 mm (0.2008 in.) 34 5.34 mm (0.2102 in.) 58 5.58 mm (0.2197 in.)
12 5.12 mm (0.2016 in.) 36 5.36 mm (0.2110 in.) 60 5.60 mm (0.2205 in.)
14 5.14 mm (0.2024 in.) 38 5.38 mm (0.2118 in.) 62 5.62 mm (0.2213 in.)
16 5.16 mm (0.2031 in.) 40 5.40 mm (0.2126 in.) 64 5.64 mm (0.2220 in.)
18 5.18 mm (0.2039 in.) 42 5.42 mm (0.2134 in.) 66 5.66 mm (0.2228 in.)
20 5.20 mm (0.2047 in.) 44 5.44 mm (0.2142 in.) 68 5.68 mm (0.2236 in.)
22 5.22 mm (0.2055 in.) 46 5.46 mm (0.2150 in.) 70 5.70 mm (0.2244 in.)
24 5.24 mm (0.2063 in.) 48 5.48 mm (0.2157 in.) 72 5.72 mm (0.2252 in.)
26 5.26 mm (0.2071 in.) 50 5.50 mm (0.2165 in.) 74 5.74 mm (0.2260 in.)
28 5.28 mm (0.2079 in.) 52 5.52 mm (0.2173 in.) - -



g.

Install the camshaft sub-assemblies.

Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CAMSHAFT>INSTALLATION