Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › TIMING BELT
RM3250E _51 Engine / Hybrid System _037989 1KD-FTV ENGINE MECHANICAL _0193242 TIMING BELT A

1KD-FTV ENGINE MECHANICAL  TIMING BELT  INSTALLATION  


PROCEDURE

Hide 13505 1.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

a.

Using a 10 mm hexagon wrench, install a new timing belt idler spacer and the No. 1 timing belt idler sub-assembly to the timing gear cover with the timing belt idler shaft.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


b.

Check that the No. 1 timing belt idler sub-assembly pulley moves smoothly.

If the No. 1 timing belt idler sub-assembly pulley does not move smoothly, check the installation condition of the No. 1 timing belt idler sub-assembly and timing belt idler spacer.


Hide 13568 2.INSTALL TIMING BELT

a.
A352029C01
2.99,0.573 3.156,1.156 3.156,1.156 3.156,1.323 true 2.865,0.552 2.25,0.167 2.25,0.167 2.083,0.167 true 0.417,2.427 0.417,2.26 0.417,2.26 0.667,1.844 true 0.677,1.5 0.51,0.917 0.51,0.917 0.344,0.917 true 1.917,0.052 2.146,0.219 0.229,0.167 10 false *a 3.083,1.333 3.313,1.5 0.229,0.167 10 false *a 0.167,0.813 0.354,0.979 0.188,0.167 10 false *a 0.344,2.438 0.531,2.604 0.188,0.167 10 false *a
*a Timing Mark


Check that the timing marks are aligned as shown in the illustration.

NOTICE:
·

Make sure that the engine is cold.

·

When turning the crankshaft pulley, the valve heads will hit against the piston. Do not turn the crankshaft pulley more than necessary.



HINT:

If reusing the timing belt, align the points marked during removal, and install the timing belt with the arrow pointing in the direction of crankshaft revolution.



b.

Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler sub-assembly in sequence.


c.
A352030

Place the No. 1 timing belt tensioner assembly upright. Then set a press on the top of the No. 1 timing belt tensioner assembly.

NOTICE:
·

Do not scratch or deform the No. 1 timing belt tensioner assembly rod end.

·

Press in the No. 1 timing belt tensioner assembly rod.

·

Protect the tip of the No. 1 timing belt tensioner assembly push rod with a cloth in order to prevent damage.




d.

Using the press, slowly push in the No. 1 timing belt tensioner assembly push rod using 981 to 9800 N (100 to 999 kgf, 220 to 2203 lbf) of force.

NOTICE:

Do not apply a load of over 9800 N (999 kgf, 2203 lbf) to the No. 1 timing belt tensioner assembly push rod.



e.

Align the holes of the No. 1 timing belt tensioner assembly push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to fix the No. 1 timing belt tensioner assembly push rod in place.


f.

Temporarily install the No. 1 timing belt tensioner assembly to the timing gear cover with the 2 bolts while pushing the No. 1 timing belt idler sub-assembly pulley toward the timing belt.


g.

Tighten the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Uniformly tighten the 2 bolts.



h.
A352031

Remove the 1.5 mm hexagon wrench from the No. 1 timing belt tensioner assembly.


i.
A352021C01
0.667,0.448 1.563,0.448 true 0.677,0.76 1,0.76 1,0.76 1,0.458 true 2.51,0.979 2.677,0.979 2.677,0.979 3.01,1.813 true 3.063,2.75 3.063,2.583 3.063,2.583 3.156,1.844 true 1.583,0.344 1.833,0.51 0.25,0.167 10 false *a 2.333,0.865 2.583,1.031 0.25,0.167 10 false *a 3,2.76 3.25,2.927 0.25,0.167 10 false *a
*a Timing Mark


Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.


Hide 11322A 3.INSTALL NO. 1 TIMING BELT COVER

a.

Install the No. 1 timing belt cover and 6 washers to the No. 2 timing belt cover and timing gear cover with the 6 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 16571C 5.INSTALL NO. 1 RADIATOR HOSE

Hide 51410 8.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY