Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM3250E _51 Engine / Hybrid System _037989 1KD-FTV ENGINE MECHANICAL _0193248 ENGINE UNIT A

1KD-FTV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 11201 2.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23670 3.REMOVE INJECTOR ASSEMBLY

Hide 11322B 5.REMOVE NO. 2 TIMING BELT COVER

Hide 13751 7.REMOVE VALVE LIFTER

a.

Remove the valve lifters from the cylinder head sub-assembly.

HINT:

Arrange the valve lifters in the correct order.



Hide 11101 8.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 9.REMOVE CYLINDER HEAD GASKET

Hide 16100 10.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A352062

Remove the 5 bolts, 2 nuts, engine water pump assembly and gasket from the cylinder block sub-assembly.


Hide 11.REMOVE TIMING GEAR COVER

NOTICE:

As the fuel supply pump assembly is not installed, the injection gear is loose inside the timing gear case assembly. Do not allow the injection gear to fall.


HINT:

To prevent the injection gear from falling, temporarily install the fuel supply pump assembly.


a.

Remove the bolt and No. 1 vacuum transmitting pipe.


b.
A352063

Remove the 14 bolts and 2 nuts.


c.
A352064

Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.

NOTICE:

Be careful not to drop the injection gear.



d.
A051310

Remove the O-ring from the timing gear case assembly.


Hide 13613E 12.REMOVE INJECTION GEAR

a.
A222329

Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.



b.
A222330

Remove the injection gear from the timing gear case assembly.


Hide 19315 13.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A239296

Remove the No. 1 crankshaft position sensor plate from the crankshaft.


Hide 14.INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO OIL PUMP GEAR

a.
A060171

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the crankshaft timing gear or timing gear case assembly.


Hide 15.INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR

a.
A060170

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the crankshaft timing gear or No. 1 idle gear.


Hide 16.INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE

a.
A060169

Using a dial indicator, measure the thrust clearance.

Standard thrust clearance:

0.06 to 0.11 mm (0.00236 to 0.00433 in.)


Maximum thrust clearance:

0.3 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the idle gear thrust plate. If necessary, replace the No. 1 idle gear or No. 1 idle gear shaft.


Hide 13521 17.REMOVE CRANKSHAFT TIMING GEAR

a.
A222332N03
1.458,1.198 0.969,1.646 0.969,1.646 0.885,1.646 false 0.542,1.552 0.854,1.719 0.313,0.167 10 false SST

Using SST, remove the crankshaft timing gear from the crankshaft.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)


Hide 18.INSPECT BACKLASH OF INJECTION GEAR TO NO. 1 IDLE GEAR

a.

Install the fuel supply pump assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.
A060158N03
1.073,1.198 0.719,1.813 0.719,1.813 0.51,1.813 true 0.177,1.719 0.51,1.906 0.333,0.188 10 false SST

Using SST, install the injection gear with the nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)


c.
A060172

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the injection gear or No. 1 idle gear.


Hide 13572 19.REMOVE IDLE GEAR THRUST PLATE

a.
A238857

Remove the 2 bolts and idle gear thrust plate from the No. 1 idle gear shaft.


Hide 13525 20.REMOVE NO. 1 IDLE GEAR

a.
A238858

Remove the No. 1 idle gear together with the No. 2 idle sub gear from the No. 1 idle gear shaft.


Hide 13581 21.REMOVE NO. 1 IDLE GEAR SHAFT

a.
A238859

Remove the No. 1 idle gear shaft from the timing gear case assembly.


Hide 22.INSPECT BACKLASH OF NO. 1 BALANCESHAFT TO OIL PUMP GEAR

a.
G036494

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the No. 1 balanceshaft sub-assembly or timing gear case assembly.


Hide 23.INSPECT BACKLASH OF NO. 2 BALANCESHAFT TO INJECTION GEAR

a.
G036495

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the No. 2 balanceshaft assembly or injection gear.


b.
A060158N03
1.073,1.198 0.719,1.813 0.719,1.813 0.51,1.813 true 0.177,1.719 0.51,1.906 0.333,0.188 10 false SST

Using SST, remove the nut and injection gear.

SST
09960-10010  (09962-01000, 09963-01000)


c.

Remove the 2 nuts and fuel supply pump assembly.


d.

Remove the gears and timing gear case.


Hide 13537 24.REMOVE NO. 1 IDLE SUB GEAR

a.
A069830

Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.

NOTICE:

Be careful not to damage the gears.



b.
A069831C01
1.781,0.26 2.563,0.26 false 0.646,0.552 0.313,0.958 true 2.604,0.177 2.813,0.344 0.208,0.167 10 false *1 0.094,1.021 0.417,1.177 0.323,0.156 10 false SST
*1 Service Bolt


Using SST, turn the No. 1 idle sub gear clockwise and remove the service bolt.

SST
09960-10010  (09962-01000, 09963-00600)


c.
A069832

Using snap ring pliers, remove the snap ring.


d.
A069833C01
2.031,0.219 2.646,0.219 false 2.021,1.104 2.635,1.104 false 0.865,0.635 1.479,0.635 false 2.688,0.125 2.906,0.292 0.219,0.167 10 false *1 2.667,1.01 2.885,1.177 0.219,0.167 10 false *3 0.667,0.542 0.844,0.708 0.177,0.167 10 false *2
*1 Wave Washer
*2 No. 1 Idle Sub Gear
*3 Idle Gear Spring


Remove the wave washer, No. 1 idle sub gear and idle gear spring.


Hide 13538 25.REMOVE NO. 2 IDLE SUB GEAR

a.
A051322

Turn the No. 1 idle gear over and set it in a vise.

NOTICE:

Be careful not a damage the gear.



b.
A069834

Using snap ring pliers, remove the snap ring.


c.
A069835C01
1.979,0.24 2.49,0.24 false 1.979,1.063 2.49,1.063 false 0.917,0.667 1.438,0.667 false 2.521,0.135 2.719,0.333 0.198,0.198 10 false *1 2.531,0.958 2.729,1.156 0.198,0.198 10 false *3 0.74,0.573 0.906,0.771 0.167,0.198 10 false *2
*1 Wave Washer
*2 No. 2 Idle Sub Gear
*3 Idle Gear Spring


Remove the wave washer, No. 2 idle sub gear and idle gear spring.


Hide 12101 26.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the 22 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut through the applied sealer and remove the oil pan sub-assembly from the cylinder block sub-assembly.

NOTICE:
·

Do not use the oil pan seal cutter for the area between the oil pan sub-assembly and timing gear case assembly, or for the area between the oil pan sub-assembly and rear oil seal retainer.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 15104 27.REMOVE OIL STRAINER SUB-ASSEMBLY

a.

Remove the 2 bolts, 2 nuts, oil strainer sub-assembly and gasket from the cylinder block sub-assembly.


Hide 11320 28.REMOVE TIMING GEAR CASE ASSEMBLY

a.
A069842

Remove the union bolt and 8 bolts.


b.
A102853

Pry the timing gear case assembly at the location shown in the illustration and remove the timing gear case assembly and gasket from the cylinder block sub-assembly.


c.
A069840

Remove the 2 O-rings from the cylinder block sub-assembly.


Hide 29.INSPECT NO. 1 BALANCESHAFT THRUST CLEARANCE

a.
A051347

Using a dial indicator, measure the thrust clearance while moving the No. 1 balanceshaft sub-assembly back and forth.

Standard thrust clearance:

0.065 to 0.140 mm (0.00256 to 0.00551 in.)


Maximum thrust clearance:

0.25 mm (0.00984 in.)


If the thrust clearance is more than the maximum clearance, replace the balanceshaft thrust washer.

If the thrust clearance is still more than the maximum clearance, replace the No. 1 balanceshaft sub-assembly.


Hide 13601A 30.REMOVE NO.1 BALANCESHAFT SUB-ASSEMBLY

a.
A051332

Remove the 2 bolts and No. 1 balanceshaft sub-assembly from the cylinder block sub-assembly.


Hide 13632 31.REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR

a.
A051333

Mount the No. 1 balanceshaft sub-assembly between aluminum plates in a vise.

NOTICE:

Be careful not to damage the No. 1 balanceshaft sub-assembly.



b.

Remove the bolt, No. 1 balanceshaft driven gear and balanceshaft thrust washer from the No. 1 balanceshaft sub-assembly.


Hide 32.INSPECT NO. 2 BALANCESHAFT THRUST CLEARANCE

a.
A051347

Using a dial indicator, measure the thrust clearance while moving the No. 2 balanceshaft sub-assembly back and forth.

Standard thrust clearance:

0.065 to 0.140 mm (0.00256 to 0.00551 in.)


Maximum thrust clearance:

0.25 mm (0.00984 in.)


If the thrust clearance is more than the maximum clearance, replace the balanceshaft thrust washer.

If the thrust clearance is still more than the maximum clearance, replace the No. 2 balanceshaft sub-assembly.


Hide 13602 33.REMOVE NO. 2 BALANCESHAFT SUB-ASSEMBLY

a.
A051334

Remove the 2 bolts and No. 2 balanceshaft sub-assembly from the cylinder block sub-assembly.


Hide 13633 34.REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR

a.
A051335

Mount the No. 2 balanceshaft sub-assembly between aluminum plates in a vise.

NOTICE:

Be careful not to damage the No. 2 balanceshaft sub-assembly.



b.

Remove the bolt, No. 2 balanceshaft driven gear and balanceshaft thrust washer from the No. 2 balanceshaft sub-assembly.


Hide 11381 35.REMOVE REAR ENGINE OIL SEAL RETAINER

A052295

a.

Remove the 5 bolts.


b.

Using a screwdriver, remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block sub-assembly.


Hide 11381A 36.REMOVE REAR ENGINE OIL SEAL

a.
A061819

Using a screwdriver and hammer, tap out the rear engine oil seal from the rear engine oil seal retainer.


Hide 11303A 37.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A058121

Using a screwdriver and hammer, tap out the front crankshaft oil seal from the timing gear cover.


Hide 11301Q 38.REMOVE INJECTION PUMP OIL SEAL

a.
A058117

Using a screwdriver and hammer, tap out the injection pump oil seal from the timing gear cover.