11448
1.REMOVE CYLINDER BLOCK OIL ORIFICE
2.INSPECT CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
0.1 to 0.3 mm (0.00394 to 0.0118 in.)
0.4 mm (0.0157 in.)
If the thrust clearance is more than the maximum, replace the connecting rod assembly. If necessary, replace the crankshaft.
3.INSPECT CONNECTING ROD OIL CLEARANCE
| *a | Matchmark |
Check the matchmarks on the connecting rod and connecting rod cap to ensure correct reassembly.
Remove the 2 connecting rod bolts.
Using the 2 removed connecting rod bolts, move the connecting rod cap back and forth to remove the connecting rod cap.
Remove the lower connecting rod bearing from the connecting rod cap.
Keep the lower connecting rod bearing and connecting rod cap together.
Clean the crank pin and connecting rod bearings.
Check the crank pin and connecting rod bearings for pitting and scratches.
If the crank pin or a connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, grind or replace the crankshaft.
| *a | Plastigage |
Lay a strip of Plastigage across the crank pin.
Install the connecting rod cap.
Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY
Do not turn the crankshaft.
Remove the 2 connecting rod bolts, connecting rod cap and lower connecting rod bearing.
| *a | Plastigage |
| *a | Mark 1, 2 or 3 |
| *b | Mark 2, 3 or 4 |
| *c | No. 1 |
| *d | No. 2 |
| *e | No. 3 |
| *f | No. 4 |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
|---|---|
| STD | 0.036 to 0.054 mm (0.00142 to 0.00212 in.) |
| U/S 0.25, U/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
0.1 mm (0.00394 in.)
If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, grind or replace the crankshaft.
If using a standard connecting rod bearing, replace it with one that has the same number. If the number of the connecting rod bearing cannot be determined, select the correct connecting rod bearing by adding together the numbers imprinted on the crankshaft and connecting rod cap, and then selecting the connecting rod bearing with the same number as the total. There are 5 sizes of standard connecting rod bearings, marked 2, 3, 4, 5 and 6.
| Item | Number Mark | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Connecting rod cap | 1 | 2 | 3 | ||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 |
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 |
EXAMPLE:
Connecting rod cap 3 + Crankshaft 1 = Total number 4 (Use connecting rod bearing 4)
| Item | Specified Condition |
|---|---|
| Mark 1 | 62.014 to 62.020 mm (2.4415 to 2.4417 in.) |
| Mark 2 | 62.020 to 62.026 mm (2.4417 to 2.4420 in.) |
| Mark 3 | 62.026 to 62.032 mm (2.4420 to 2.4422 in.) |
| Item | Specified Condition |
|---|---|
| Mark 1 | 58.994 to 59.000 mm (2.3226 to 2.3228 in.) |
| Mark 2 | 58.988 to 58.994 mm (2.3224 to 2.3226 in.) |
| Mark 3 | 58.982 to 58.988 mm (2.3221 to 2.3224 in.) |
| Item | Specified Condition |
|---|---|
| Mark 2 | 1.486 to 1.489 mm (0.0585 to 0.0586 in.) |
| Mark 3 | 1.489 to 1.492 mm (0.0586 to 0.0587 in.) |
| Mark 4 | 1.492 to 1.495 mm (0.0587 to 0.0589 in.) |
| Mark 5 | 1.495 to 1.498 mm (0.0589 to 0.0590 in.) |
| Mark 6 | 1.498 to 1.501 mm (0.0590 to 0.0591 in.) |
Completely remove the Plastigage.
4.REMOVE PISTON AND CONNECTING ROD
| *a | Ridge Reamer |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push the piston, connecting rod and upper connecting rod bearing through the top of the cylinder block sub-assembly to remove them.
Remove the upper connecting rod bearing from the connecting rod.
Keep the connecting rod bearings, connecting rod and connecting rod cap together.
Be sure to organize the removed piston and connecting rod in such a way that they can be reinstalled exactly as before.
13041
5.REMOVE CONNECTING ROD BEARING
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
Arrange the removed parts in the correct order.
13011
6.REMOVE PISTON RING SET
Using a piston ring expander, remove the No. 1 piston ring and No. 2 piston ring.
Be sure to organize the removed piston rings in such a way that they can be reinstalled exactly as before.
Remove the coil and oil ring by hand.
13101
7.REMOVE PISTON WITH PIN SUB-ASSEMBLY
Using a small screwdriver, pry out the 2 snap rings from the piston.
Gradually heat the piston to approximately 80°C (176°F).
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod.
The piston and piston pin are a matched set.
Be sure to organize the removed pistons, piston pins, piston rings, connecting rod sub-assemblies and connecting rod bearings in such a way that the parts can be reinstalled exactly as before.
8.INSPECT CRANKSHAFT THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
0.04 to 0.24 mm (0.00157 to 0.00945 in.)
0.3 mm (0.0118 in.)
If the thrust clearance is more than the maximum, replace the crankshaft thrust washer.
| Item | Specified Condition |
|---|---|
| STD | 2.430 to 2.480 mm (0.0957 to 0.0976 in.) |
| O/S 0.125 | 2.555 to 2.605 mm (0.1005 to 0.1025 in.) |
| O/S 0.250 | 2.680 to 2.730 mm (0.1055 to 0.1074 in.) |
9.INSPECT CRANKSHAFT OIL CLEARANCE
Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.
Using the removed crankshaft bearing cap bolts, pry the cap back and forth and remove the crankshaft bearing caps, lower crankshaft bearings and lower crankshaft thrust washers (No. 5 crankshaft bearing cap only).
Keep the lower crankshaft bearing and crankshaft bearing cap together.
Be sure to organize the crankshaft bearing caps and lower crankshaft thrust washers (No. 5 crankshaft bearing only) in such a way that they can be reinstalled exactly as before.
Lift out the crankshaft.
Clean each main journal and crankshaft bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If a journal or one of its crankshaft bearings is damaged, replace the crankshaft bearings for that journal. If necessary, grind or replace the crankshaft.
Place the crankshaft on the cylinder block sub-assembly.
| *a | Plastigage |
Lay a strip of Plastigage across each journal.
Install the crankshaft bearing caps.
Do not turn the crankshaft.
Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY
Remove the crankshaft bearing caps.
| *a | Plastigage |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
|---|---|
| STD | 0.030 to 0.048 mm (0.00118 to 0.00189 in.) |
| U/S 0.25, U/S 0.50 | 0.037 to 0.077 mm (0.00146 to 0.00303 in.) |
0.1 mm (0.00394 in.)
If the oil clearance is more than the maximum, replace the crankshaft bearings. If necessary, grind or replace the crankshaft.
If replacing the cylinder block sub-assembly, the crankshaft bearing oil clearance will be within the standard range.
0.030 to 0.048 mm (0.00118 to 0.00189 in.)
If using a standard crankshaft bearing, replace it with one that has the same number. If the number of the crankshaft bearing cannot be determined, select the correct crankshaft bearing by adding together the numbers imprinted on the cylinder block sub-assembly and crankshaft, and then selecting the crankshaft bearing with the same number as the total. There are 5 sizes of standard crankshaft bearings, marked 2, 3, 4, 5 and 6.
| Item | Number Mark | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Cylinder block sub-assembly | 1 | 2 | 3 | ||||||
| Crankshaft | 1 | 2 | 3 | 1 | 2 | 3 | 1 | 2 | 3 |
| Bearing to be used | 2 | 3 | 4 | 3 | 4 | 5 | 4 | 5 | 6 |
EXAMPLE:
Cylinder block sub-assembly 2 + Crankshaft 1 = Total number 3 (Use bearing 3)
| Item | Specified Condition |
|---|---|
| Mark 1 | 75.000 to 75.006 mm (2.9528 to 2.9530 in.) |
| Mark 2 | 75.006 to 75.012 mm (2.9530 to 2.9532 in.) |
| Mark 3 | 75.012 to 75. 018 mm (2.9532 to 2.9535 in.) |
| Item | Specified Condition |
|---|---|
| Mark 1 | 69.994 to 70.000 mm (2.7557 to 2.7559 in.) |
| Mark 2 | 69.988 to 69.994 mm (2.7554 to 2.7557 in.) |
| Mark 3 | 69.982 to 69.988 mm (2.7552 to 2.7554 in.) |
| Item | Specified Condition |
|---|---|
| Mark 2 | 2.482 to 2.485 mm (0.0977 to 0.0978 in.) |
| Mark 3 | 2.485 to 2.488 mm (0.0978 to 0.0980 in.) |
| Mark 4 | 2.488 to 2.491 mm (0.0980 to 0.0981 in.) |
| Mark 5 | 2.491 to 2.494 mm (0.0981 to 0.0982 in.) |
| Mark 6 | 2.494 to 2.497 mm (0.0982 to 0.0983 in.) |
| *a | Front | *b | No. 1 |
| *c | No. 2 | *d | No. 3 |
| *e | No. 4 | *f | No. 5 |
| *g | Mark 2, 3, 4, 5 or 6 | - | - |
Completely remove the Plastigage.
13411
10.REMOVE CRANKSHAFT
Lift out the crankshaft.
Remove the upper crankshaft bearings and upper crankshaft thrust washers (No. 5 crankshaft bearing only) from the cylinder block sub-assembly.
Arrange the crankshaft bearing caps, crankshaft bearings and crankshaft thrust washers (No. 5 crankshaft bearing only) in the correct order.
15708
11.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
Remove the 4 check valves and 4 No. 1 oil nozzle sub-assemblies.
12.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Remove the stud bolts from the cylinder block sub-assembly.