Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › TIMING BELT
RM3250E _51 Engine / Hybrid System _038014 2KD-FTV ENGINE MECHANICAL _0193254 TIMING BELT A

2KD-FTV ENGINE MECHANICAL  TIMING BELT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)
Replacement of timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 16571C 3.REMOVE NO, 1 RADIATOR HOSE

Hide 16711 4.REMOVE FAN SHROUD

Hide 11322A 5.REMOVE NO. 1 TIMING BELT COVER

a.
A352020

Remove the 6 bolts, 6 washers and No. 1 timing belt cover from the No. 2 timing belt cover and timing gear cover.


Hide 13568 6.REMOVE TIMING BELT

a.
A352021C01
0.667,0.448 1.563,0.448 true 0.677,0.76 1,0.76 1,0.76 1,0.458 true 2.51,0.979 2.677,0.979 2.677,0.979 3.01,1.813 true 3.063,2.75 3.063,2.583 3.063,2.583 3.156,1.844 true 1.583,0.344 1.833,0.51 0.25,0.167 10 false *a 2.333,0.865 2.583,1.031 0.25,0.167 10 false *a 3,2.76 3.25,2.927 0.25,0.167 10 false *a
*a Timing Mark


Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

HINT:

If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.



b.
A352022

Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner assembly from the timing gear cover.


c.

Remove the timing belt.

HINT:
A352023N01
2.406,0.479 2.802,0.677 0.396,0.198 10 true 90°

·

If turning the camshaft sub-assembly while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.

·

When installing the timing belt, turn the camshaft sub-assembly to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.




Hide 13505 7.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:

When inspecting the No. 1 timing belt idler sub-assembly, do not remove it unless absolutely necessary.


a.

Using a 10 mm hexagon wrench, remove the timing belt idler shaft, No. 1 timing belt idler sub-assembly and timing belt idler spacer from the timing gear cover.