Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER BLOCK
RM3250E _51 Engine / Hybrid System _038014 2KD-FTV ENGINE MECHANICAL _0193262 CYLINDER BLOCK A

2KD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 11431A 1.REPLACE CYLINDER BLOCK TIGHT PLUG

NOTICE:

If coolant leaks from a tight plug or a plug is corroded, replace it.


a.

Remove the tight plugs.


b.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Do not start the engine for 1 hour after installation.



c.

Position A:

Using a 14 mm steel bar and hammer, tap in the tight plug as shown in the illustration.


d.

Other positions:

Using SST and a hammer, tap in the tight plugs as shown in the illustration.

Position B

SST
09950-60010  (09951-00180)
09950-70010  (09951-07100)

Position C

SST
09950-60010  (09951-00190)
09950-70010  (09951-07100)

Position D

SST
09950-60010  (09951-00200)
09950-70010  (09951-07100)

Position E and H

SST
09950-60010  (09951-00350)
09950-70010  (09951-07100)

Position F

SST
09950-60010  (09951-00400, 09951-00450)
09950-70010  (09951-07100)

Position G

SST
09950-60010  (09951-00450)
09950-70010  (09951-07100)

A303259C04
3.719,0.125 4.031,0.323 0.313,0.198 10 false *b 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.052,2.146 0.365,2.344 0.313,0.198 10 false *c 2.833,2.135 3.146,2.333 0.313,0.198 10 false *d 0.948,0.354 1.146,0.552 0.198,0.198 10 false E 1.375,0.354 1.573,0.552 0.198,0.198 10 false E 1.844,0.354 2.042,0.552 0.198,0.198 10 false E 4.99,0.365 5.219,0.615 0.229,0.25 10 false H 5.427,0.385 5.656,0.635 0.229,0.25 10 false H 4.552,0.375 4.781,0.625 0.229,0.25 10 false H 0.833,2.313 1.063,2.563 0.229,0.25 10 false D 1.854,3.167 2.083,3.417 0.229,0.25 10 false C 2.615,3.292 2.844,3.542 0.229,0.25 10 false F 2.906,2.875 3.135,3.125 0.229,0.25 10 false B 3.458,2.469 3.688,2.719 0.229,0.25 10 false G 4.385,3.25 4.615,3.5 0.229,0.25 10 false F 6.677,3.344 6.906,3.594 0.229,0.25 10 false *e 4.885,1.167 5.115,1.417 0.229,0.25 10 false A
*a Right Side *b Left Side
*c Front Side *d Rear Side
*e Stops - -



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap in new straight pins to the cylinder block sub-assembly.

Standard Protrusion Height:
Item Specified Condition
Pin A 7.5 mm (0.295 in.) or less
Pin B 6 mm (0.234 in.) or less
Pin C 12 mm (0.472 in.) or less


A303260C05
0.719,0.167 1.031,0.365 0.313,0.198 10 false *a 3.958,0.198 4.146,0.406 0.188,0.208 10 false *b 1.323,2.927 1.51,3.135 0.188,0.208 10 false *c 2.906,2.938 3.094,3.146 0.188,0.208 10 false *d 4.604,2.938 4.792,3.146 0.188,0.208 10 false *e 6.281,2.417 6.469,2.625 0.188,0.208 10 false *l 2.469,0.792 2.781,0.99 0.313,0.198 10 false A 1.188,2.26 1.5,2.458 0.313,0.198 10 false A 3.906,1.458 4.135,1.625 0.229,0.167 10 false C 4.125,1.563 4.354,1.729 0.229,0.167 10 false B 5.51,1.615 5.74,1.781 0.229,0.167 10 false B 6.104,1.813 6.333,1.979 0.229,0.167 10 false C 0.771,3.5 0.958,3.708 0.188,0.208 10 false *f 1.323,4.198 1.51,4.406 0.188,0.208 10 false *g 2.344,3.49 2.531,3.698 0.188,0.208 10 false *h 2.906,4.198 3.094,4.406 0.188,0.208 10 false *i 4.625,4.198 4.813,4.406 0.188,0.208 10 false *k 4.083,3.458 4.271,3.667 0.188,0.208 10 false *j
*a Front Side *b Rear Side
*c Pin A *d Pin B
*e Pin C *f 18 mm (0.709 in.)
*g 8 mm (0.3.15 in.) *h 11 mm (0.433 in.)
*i 6 mm (0.236 in.) *j 22 mm (0.866 in.)
*k 10 mm (0.394 in.) *l Protrusion height



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins to the cylinder block sub-assembly.

Standard Protrusion:

6 mm (0.236 in.) or less


A256496C06
0.646,0.292 0.865,0.5 0.219,0.208 10 false *a 3.51,1.031 3.75,1.219 0.24,0.188 10 false *b 6.292,1.625 6.521,1.833 0.229,0.208 10 false *d 4.302,1.51 4.542,1.698 0.24,0.188 10 false *c
*a Cylinder Head Side *b 10.5 mm (0.413 in.)
*c 15 mm (0.590 in.) *d 6 mm (0.236 in.) or less



Hide 11415A 4.REPLACE CYLINDER BLOCK WATER DRAIN COCK PLUG

NOTICE:

If coolant leaks from a cylinder block water drain plug or a cylinder block water drain plug is corroded, replace the cylinder block water drain plug.


a.

Remove the cylinder block water drain plug from the cylinder block.


b.

Clean the cylinder block side hole and new cylinder block water drain plug with non-residue solvent.


c.
A330617C01
1.896,3.24 2.052,2.583 2.052,2.583 2.219,2.583 true 2.021,3.458 2.271,3.792 2.271,3.792 2.438,3.792 true 1.906,4.094 2.167,4.479 2.167,4.479 2.333,4.479 true 2.667,1.208 2.896,1.375 0.229,0.167 10 false *a 2.26,2.49 2.49,2.646 0.229,0.156 10 false *b 2.469,3.698 2.698,3.854 0.229,0.156 10 false *c 2.365,4.385 2.615,4.552 0.25,0.167 10 false *d
*a Front
*b 5.0 mm (0.197 in.)
*c 2.0 mm (0.787 in.)
*d Adhesive


Apply adhesive onto the shaded area of a cylinder block water drain plug as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the cylinder block water drain plug within 3 minutes after applying adhesive.



d.

Set the cylinder block water drain plug and tap it until the edge of the cylinder block water drain plug fits against the chamfered part of the cylinder block as shown in the illustration.