Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0193493 CYLINDER HEAD A

1TR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A101402N09
1.146,0.875 0.469,0.302 0.469,0.302 1.063,1.271 true 0.125,0.198 0.417,0.396 0.292,0.198 10 false SST

Using SST and a hammer, tap out the intake valve guide bush from the cylinder head sub-assembly.

SST
09201-01055  
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.405 to 0.406 in.)
O/S 0.05 10.335 to 10.356 mm (0.407 to 0.408 in.)


If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore diameter to between 10.335 and 10.356 mm (0.407 and 0.408 in.).

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Select a new intake valve guide bush (STD or O/S 0.05).

Intake Valve Guide Bush:
Bush Size Specified Condition
Use STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
Use O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Standard bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)



f.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



g.

Place the cylinder head sub-assembly on wooden blocks.


h.
A101405C08
1.063,1.229 0.427,0.229 0.427,0.229 1.135,0.813 true 2.948,1.271 3.156,1.51 0.208,0.24 10 false *a 0.104,0.125 0.448,0.323 0.344,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Standard protrusion height:

9.8 to 10.2 mm (0.386 to 0.402 in.)



i.
A101406

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard specified clearance between the intake valve guide bush and intake valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



b.

Place the cylinder head sub-assembly on wooden blocks.


c.
G037435N06
1.844,0.719 2.198,0.198 2.198,0.198 1.979,1.115 true 2.229,0.083 2.677,0.323 0.448,0.24 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush from the cylinder head sub-assembly.

SST
09201-01055  
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.405 to 0.406 in.)
O/S 0.05 10.335 to 10.356 mm (0.407 to 0.408 in.)


If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore diameter to between 10.335 and 10.356 mm (0.407 and 0.408 in.).

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Select a new exhaust valve guide bush (STD or O/S 0.05).

Exhaust Valve Guide Bush:
Bush Size Specified Condition
Use STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
Use O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Standard bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)



f.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



g.

Place the cylinder head sub-assembly on wooden blocks.


h.
A101408C08
1.792,0.646 1.99,0.104 1.99,0.104 1.896,1.042 true 0.948,1.354 1.219,1.563 0.271,0.208 10 false *a 2.01,0 2.375,0.198 0.365,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Standard protrusion height:

7.6 to 8.0 mm (0.299 to 0.315 in.)



i.
A101409

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard specified clearance between the exhaust valve guide bush and exhaust valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11151A 3.REPLACE CAMSHAFT BEARING CAP SETTING RING PIN

A302858C04
0.958,2.677 1.271,2.833 0.313,0.156 10 false *a 0.396,2.229 0.708,2.385 0.313,0.156 10 false *b 2.802,2.344 3.115,2.5 0.313,0.156 10 false *c
*a Height
*b Width
*c Protrusion Height


NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

Standard Ring Pin:
Item Height Width Protrusion Height
Ring pin 7 mm (0.276 in.) 10 mm (0.394 in.) 2.5 to 3.8 mm (0.0984 to 0.150 in.)