Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0193493 CYLINDER HEAD A

1TR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


A353229C01
1.583,2.417 1.417,2.417 1.417,2.417 1.271,2.063 true 2.833,2.417 3,2.417 3,2.417 3.229,2.01 true 4.75,1.583 4.583,1.583 4.583,1.583 4.219,0.896 true 6.083,0.25 6.25,0.25 6.25,0.25 6.656,0.844 true 1.5,4 1.333,4 1.333,4 1.24,3.781 true 6.417,3.5 6.25,3.5 6.25,3.5 6.052,2.792 true 6.25,3.5 6.448,3.104 true 5.583,3.5 5.417,3.5 5.417,3.5 5.229,2.781 true 5.417,3.5 5.542,3.115 true 4.667,3.5 4.5,3.5 4.5,3.5 4.302,2.781 true 4.5,3.5 4.74,3.115 true 0.333,0.135 0.646,0.292 0.313,0.156 10 false *a 3.729,0.177 4.042,0.333 0.313,0.156 10 false *b 0.875,2.635 1.188,2.792 0.313,0.156 10 false *c 3.792,1.823 4.104,1.979 0.313,0.156 10 false *d 0.667,4.948 0.979,5.104 0.313,0.156 10 false *e 0.677,5.531 0.99,5.688 0.313,0.156 10 false *f 1.156,5.115 1.479,5.385 0.323,0.271 10 false *g 3.01,4.635 3.323,4.792 0.313,0.156 10 false *h 3.01,5.479 3.323,5.635 0.313,0.156 10 false *i 3.5,4.885 3.813,5.229 0.313,0.344 10 false *j 5.26,4.844 5.573,5 0.313,0.156 10 false *k 5.76,5.073 6.073,5.229 0.313,0.156 10 false *l 5.26,5.458 5.573,5.615 0.313,0.156 10 false *i 1.615,2.333 1.771,2.531 0.156,0.198 10 false A 2.677,2.333 2.833,2.531 0.156,0.198 10 false A 0.344,4.302 0.5,4.5 0.156,0.198 10 false A 1.521,3.917 1.677,4.115 0.156,0.198 10 false A 4.781,1.5 4.938,1.698 0.156,0.198 10 false B 5.938,0.167 6.104,0.417 0.167,0.25 10 false B 2.656,4.01 2.813,4.208 0.156,0.198 10 false B 4.698,3.417 4.854,3.615 0.156,0.198 10 false C 5.604,3.417 5.76,3.615 0.156,0.198 10 false C 6.438,3.417 6.594,3.615 0.156,0.198 10 false C 4.927,4.177 5.083,4.375 0.156,0.198 10 false C
*a Cylinder Head Upper Side *b Intake Manifold Side
*c Front Side *d Exhaust Manifold Side
*e 21 mm (0.827 in.) *f 9.0 mm (0.354 in.)
*g 34 mm (1.34 in.) *h 24 mm (0.945 in.)
*i 13 mm (0.512 in.) *j 45 mm (1.77 in.)
*k 20 mm (0.787 in.) *l 35 mm (1.38 in.)


a.

Using E6, E7 and E8 "TORX" socket wrenches, install the stud bolts.

Torque:
for stud bolt A : 3.0 N*m (31 kgf*cm, 27 in.*lbf)
for stud bolt B and C : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 11117E 2.INSTALL NO. 1 HEAD STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from the No. 1 head straight screw plug or the No. 1 head straight screw plug is corroded, replace it.


a.

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 head straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11117F 3.INSTALL NO. 2 HEAD STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from the No. 2 head straight screw plug or the No. 2 head straight screw plug is corroded, replace it.


a.

Using a 19 mm hexagon wrench, install a new gasket and the No. 2 head straight screw plug.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the 16 valve spring seats to the cylinder head sub-assembly.


Hide 13711A 5.INSTALL VALVE STEM OIL SEAL

a.
A101414C08
0.844,0.646 1.021,0.396 1.021,0.396 1.104,0.396 true 2.5,0.646 2.365,0.385 2.365,0.385 2.25,0.385 true 2.052,0.292 2.25,0.479 0.198,0.188 10 false *d 1.146,0.292 1.333,0.49 0.188,0.198 10 false *c 0.656,1.51 0.865,1.708 0.208,0.198 10 false *a 2.479,1.521 2.677,1.719 0.198,0.198 10 false *b
*a Intake Side
*b Exhaust Side
*c Gray
*d Black


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gray and the exhaust valve oil seals are black.



b.
A101415C05
2.604,0.604 2.333,0.083 2.333,0.083 2.198,0.083 true 2.99,1.406 2.667,1.906 2.667,1.906 2.521,1.906 true 1.073,1.219 0.469,1.563 0.469,1.563 0.469,1.667 true 1.979,0 2.146,0.198 0.167,0.198 10 false *1 2.229,1.802 2.604,2 0.375,0.198 10 false SST 0.281,1.688 0.656,1.885 0.375,0.198 10 false SST
*1 Valve Stem Oil Seal


Using SST, push in the 16 valve stem oil seals to install them.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

a.
A101416C08
2.652,1.492 2.849,1.687 0.197,0.195 10 *a
*a 30 mm (1.18 in.) or more


Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.
A332526C02
1.073,0.396 1.281,0.292 1.281,0.292 1.417,0.292 false 0.927,1.198 1.271,1.521 1.271,1.521 1.417,1.521 true 1.438,0.188 1.625,0.396 0.188,0.208 10 false *a 1.448,1.417 1.646,1.615 0.198,0.198 10 false *b
*a Narrow
*b Wide


Install the intake valve, inner compression spring and retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to the original locations.



c.
A333831N01
1.583,0.333 1.708,0.333 1.708,0.333 1.823,0.708 true 1.25,0.24 1.573,0.427 0.323,0.188 10 false SST

Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  
09202-00021  


d.
A333836C03
0.469,1.813 0.469,1.625 0.469,1.625 1.063,0.917 true 0.396,1.833 0.615,2.042 0.219,0.208 10 false *a
*a 5 mm Pin Punch


Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Do not damage the valve stem tip.



Hide 13715 7.INSTALL EXHAUST VALVE

A101419C08
2.673,1.465 2.833,1.656 0.16,0.191 10 *a
*a 30 mm (1.18 in.) or more


a.

Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A332527C02
0.333,0.25 0.417,0.25 0.417,0.25 0.75,0.375 false 0.5,1.594 0.583,1.594 0.583,1.594 0.917,1.208 true 0.146,0.146 0.333,0.323 0.188,0.177 10 false *a 0.333,1.49 0.531,1.688 0.198,0.198 10 false *b
*a Narrow
*b Wide


Install the exhaust valve, inner compression spring and retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to the original locations.



c.
A333832N01
0.635,0.417 0.771,0.208 0.771,0.208 0.979,0.208 false 1.031,0.115 1.354,0.302 0.323,0.188 10 false SST

Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  
09202-00021  


d.
A333837C03
1.823,0.844 2.01,0.75 2.01,0.75 3.073,0.75 true 3.104,0.667 3.313,0.844 0.208,0.177 10 false *a
*a 5 mm Pin Punch


Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Do not damage the valve stem tip.