Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0193494 CYLINDER BLOCK A

1TR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


A353233C01
2.51,0.802 2.833,0.5 2.833,0.5 3,0.5 true 5.021,2.24 5.417,1.333 5.417,1.333 5.583,1.333 true 1.01,3.385 1.333,3.083 1.333,3.083 1.5,3.083 true 2.156,3.385 2.5,3.083 2.5,3.083 2.667,3.083 true 0.854,0.344 1.167,0.5 0.313,0.156 10 false *a 3.771,1.167 4.083,1.323 0.313,0.156 10 false *b 0.771,2.927 1.083,3.083 0.313,0.156 10 false *c 1.625,5.552 1.938,5.708 0.313,0.156 10 false *d 2.396,6.396 2.708,6.552 0.313,0.156 10 false *e 4.656,5.01 4.969,5.167 0.313,0.156 10 false *f 5.25,5.5 5.563,5.75 0.313,0.25 10 false *g 4.615,6.854 4.927,7.01 0.313,0.156 10 false *h 4.635,7.302 4.948,7.458 0.313,0.156 10 false *i 5.427,7 5.75,7.26 0.323,0.26 10 false *j 1.625,7.219 1.938,7.375 0.313,0.156 10 false *d 4.667,6.031 4.979,6.188 0.313,0.156 10 false *d 3.031,0.417 3.188,0.615 0.156,0.198 10 false A 5.615,1.25 5.771,1.448 0.156,0.198 10 false B 1.531,3 1.688,3.198 0.156,0.198 10 false C 2.698,3 2.854,3.198 0.156,0.198 10 false C 1.188,5.198 1.344,5.396 0.156,0.198 10 false A 4.25,4.594 4.406,4.792 0.156,0.198 10 false B 4.229,6.354 4.385,6.552 0.156,0.198 10 false C
*a Front Side *b Exhaust Side
*c Lower Side *d 12 mm (0.472 in.)
*e 85 mm (3.35 in.) *f 18 mm (0.709 in.)
*g 60 mm (2.36 in.) *h 20 mm (0.787 in.)
*i 13 mm (0.512 in.) *j 45 mm (1.77 in.)


a.

Using an E8 "TORX" socket wrench, install the stud bolts labeled A.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Apply adhesive to the hole for the stud bolt labeled B in the cylinder block. Install the stud bolts labeled B.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

HINT:

When reusing a stud bolt, apply adhesive to the bolt before installing it.


Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Using an E7 "TORX" socket wrench, install the stud bolts labeled C.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A301270C04
1.865,1.438 1.365,1.198 1.365,1.198 1.24,1.198 false 1.948,1.573 1.656,1.906 1.656,1.906 1.51,1.906 false 1.313,1.823 1.625,1.979 0.313,0.156 10 false *a 2.24,1.75 2.552,1.906 0.313,0.156 10 false *b 1.656,0.167 1.969,0.323 0.313,0.156 10 false *c 2.354,0.792 2.667,0.948 0.313,0.156 10 false *d 0.99,1.135 1.302,1.292 0.313,0.156 10 false 30° 2.323,1.427 2.635,1.583 0.313,0.156 10 false 60°
*a Allowable Range
*b Target Direction
*c Upper Side
*d Front


Install the cylinder block water drain cock sub-assembly as shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.

·

Do not loosen the cylinder block water drain cock sub-assembly to adjust it. If an adjustment is necessary, remove the cylinder block water drain cock sub-assembly and reinstall it.




c.

Install the water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 13101 4.INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the piston sub-assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Assemble the piston and connecting rod.

i.
A103205C01
2.458,1.531 2.813,1.375 2.813,1.375 2.979,1.375 true 3.01,1.26 3.219,1.479 0.208,0.219 10 false *a
*a Service Hole Cutout Portion


Using a screwdriver, install a new snap ring at one end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



ii.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

CAUTION:

Be sure to wear protective gloves.



iii.

Coat the piston pin with engine oil.


iv.
A337633C01
1.5,0.25 1.667,0.25 1.667,0.25 2.083,0.438 true 1.5,2 1.667,2 1.667,2 2.125,1.833 true 1.333,0.167 1.646,0.323 0.313,0.156 10 false *a 1.333,1.917 1.646,2.073 0.313,0.156 10 false *a
*a Front Mark


Align the front marks of the piston and connecting rod and push in the piston pin with your thumb.

HINT:

The piston and pin are a matched set.



v.
A101515C01
2.469,1.51 2.656,1.302 2.656,1.302 2.854,1.302 true 2.896,1.219 3.104,1.396 0.208,0.177 10 false *a
*a Service Hole Cutout Portion


Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



vi.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.



Hide 13011 5.INSTALL PISTON RING SET

HINT:

Perform "Inspection After Repairs" after replacing the piston ring.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A164414C15
1.969,1.156 2.458,1.156 false 1.99,1.385 2.208,1.646 2.208,1.646 2.458,1.646 false 1.99,0.917 2.198,0.604 2.198,0.604 2.448,0.604 false 2.49,0.51 2.708,0.708 0.219,0.198 10 false *1 2.5,1.063 2.698,1.26 0.198,0.198 10 false *2 2.5,1.552 2.688,1.74 0.188,0.188 10 false *3
*1 Upper Oil Ring Side Rail
*2 Oil Ring Expander
*3 Lower Oil Ring Side Rail


Install the oil ring expander and 2 oil ring side rails by hand.


b.
A337694C01
0.5,2.333 0.667,2.333 0.667,2.333 0.969,2.552 false 1.417,2 1.583,2 1.583,2 1.833,2.354 false 0.333,2.25 0.646,2.406 0.313,0.156 10 false *1 1.25,1.927 1.563,2.083 0.313,0.156 10 false *a
*1 No. 2 Compression Ring
*a Code Mark (2N)
V100135

Upward


Using a piston ring expander, install the 2 compression rings with the code mark as shown in the illustration.

HINT:
·

The No. 1 compression ring is reversible.

·

Install the No. 2 compression ring with the code mark (2N) facing upward.




c.
A337634C01
0.667,0.833 0.833,0.833 0.833,0.833 1.198,0.958 false 0.083,0.125 0.583,0.292 0.5,0.167 10 false *1, *3 3.115,1.792 3.427,1.948 0.313,0.156 10 false *2 0.333,1.875 0.646,2.031 0.313,0.156 10 false *4 2.958,0.125 3.271,0.281 0.313,0.156 10 false *5 0.5,0.75 0.813,0.906 0.313,0.156 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the compression ring ends.



Hide 11711 6.INSTALL CRANKSHAFT BEARING

NOTICE:

Do not apply engine oil to the contact area or backside of the crankshaft bearing.


HINT:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.


a.

Clean the main journal and both surfaces of the crankshaft bearing.


b.
A302881C04
1.271,2.927 0.656,2.417 0.656,2.417 2.188,2.906 true 0.479,2.302 0.677,2.521 0.198,0.219 10 false *c 1.281,3.979 1.479,4.167 0.198,0.188 10 false *a 2.125,3.979 2.333,4.177 0.208,0.198 10 false *b
*a CORRECT
*b INCORRECT
*c Oil Groove


Install the upper crankshaft bearing.

i.

Install the upper crankshaft bearing to the cylinder block as shown in the illustration.

Reference (Difference in Dimension of Cylinder Block and Bearing):
Item Specified Condition
# 1, 5 journal 3.83 mm (0.151 in.)
# 3 journal 1.74 mm (0.0685 in.)
# 2, 4 journal 2.75 mm (0.1083 in.)


NOTICE:
·

Do not apply engine oil to the upper crankshaft bearings or their contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.





c.
A101501C06
0.938,0.552 1.083,0.552 1.083,0.552 1.26,1.031 true 1.021,1.833 0.844,1.833 0.844,1.833 0.594,1.458 false 2.74,0.438 2.99,0.708 0.25,0.271 10 false (A) 2.75,1.708 3,1.979 0.25,0.271 10 false (B) 0.75,0.448 0.927,0.604 0.177,0.156 10 false *1 1.083,1.75 1.26,1.906 0.177,0.156 10 false *2
*1 Lower Crankshaft Bearing
*2 Crankshaft Bearing Cap


Install the lower crankshaft bearing.

i.

Install the lower crankshaft bearing to the crankshaft bearing cap.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.

Dimension (A - B) or (B - A):

0.3 mm (0.0118 in.) or less


Reference (Dimension of (A) or (B)):
Item Specified Condition
# 1, 5 journal 3.83 mm (0.151 in.)
# 3 journal 1.74 mm (0.0685 in.)
# 2, 4 journal 2.75 mm (0.1083 in.)


NOTICE:

Do not apply engine oil to the crankshaft bearings or their contact surfaces.




d.

With the upper crankshaft bearing and lower crankshaft bearing installed, use a plastic-faced hammer to install the crankshaft bearing caps to the cylinder block.

NOTICE:

Make sure that the crankshaft bearing caps are installed in the correct positions and facing in the correct direction.



e.
A101502C06
2.427,0.385 2.615,0.594 0.188,0.208 10 false *a
*a Misalignment


Using a vernier caliper, measure the amount of misalignment between the upper crankshaft bearing and lower crankshaft bearing as shown in the illustration.

Standard misalignment:

0.9 mm (0.0354 in.) or less



f.

Remove the crankshaft bearing cap.


g.

Apply engine oil to the upper crankshaft thrust washers.


h.
A097960C05
1.677,1.583 1.271,1.802 1.271,1.802 1.104,1.802 false 1.417,1.323 1.271,1.802 false 0.917,1.698 1.292,1.979 0.375,0.281 10 false *a
*a Oil Groove


Install the 2 No. 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.

NOTICE:

Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged.



i.
A101504C08
0.823,1.052 0.76,0.781 0.76,0.781 0.688,0.781 false 2.417,0.323 2.688,0.323 false 0.708,1.125 0.708,1.625 true 1.083,1.542 0.719,1.542 true 0.635,1.656 0.833,1.854 0.198,0.198 10 false *b 0.479,0.667 0.677,0.854 0.198,0.188 10 false *a 2.729,0.229 2.927,0.417 0.198,0.188 10 false *a
*a Claw
*b Oil Groove


Install the 2 lower crankshaft thrust washers to the No. 3 crankshaft bearing cap with the grooves facing outward.

NOTICE:

Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged. The lower crankshaft thrust washers have a claw as shown in the illustration.



j.

Apply engine oil to the lower crankshaft bearing.


Hide 13411 7.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper crankshaft bearing, and then place the crankshaft on the cylinder block.


b.
A101506

Install the 5 crankshaft bearing caps to their proper locations.


c.

Install the crankshaft bearing cap set bolts.

i.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


ii.

Temporarily install the crankshaft bearing cap set bolts.

HINT:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.



iii.
A301273N03
2.927,1.708 3.24,1.906 0.313,0.198 10 10 2.969,0.229 3.281,0.427 0.313,0.198 10 9 2.313,0.219 2.625,0.417 0.313,0.198 10 5 1.677,0.219 1.99,0.417 0.313,0.198 10 1 1.063,0.219 1.375,0.417 0.313,0.198 10 3 0.438,0.219 0.75,0.417 0.313,0.198 10 7 0.438,1.708 0.75,1.906 0.313,0.198 10 8 1.073,1.708 1.385,1.906 0.313,0.198 10 4 1.698,1.719 2.01,1.917 0.313,0.198 10 2 2.313,1.708 2.625,1.906 0.313,0.198 10 6

Step 1:

Uniformly tighten the 10 crankshaft bearing cap set bolts in the sequence shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

If any of the crankshaft bearing cap set bolts does not meet the torque specification, replace the crankshaft bearing cap set bolt.


iv.

Mark the front of the crankshaft bearing cap set bolts with paint.


v.

Step 2:

Tighten the crankshaft bearing cap set bolts 90° in the sequence shown in step 1.


vi.

Check that the paint marks are now at a 90° angle to the front.



d.

Check that the crankshaft turns smoothly.


Hide 8.INSPECT CRANKSHAFT THRUST CLEARANCE

Hide 13041 9.INSTALL CONNECTING ROD BEARING

a.
A101528C07
2.677,0.833 2.521,0.542 2.521,0.542 2.448,0.542 true 2.281,0.427 2.469,0.625 0.188,0.198 10 false *a
*a Claw


Align the connecting rod bearing claw with the groove of the connecting rod or connecting rod cap.


b.

Install the connecting rod bearings in the connecting rod and connecting rod cap.

NOTICE:

Clean the backside of the bearing and the connecting rod bearing surface of the connecting rod.



Hide 10.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A337634C01
0.667,0.833 0.833,0.833 0.833,0.833 1.198,0.958 false 0.083,0.125 0.583,0.292 0.5,0.167 10 false *1, *3 3.115,1.792 3.427,1.948 0.313,0.156 10 false *2 0.333,1.875 0.646,2.031 0.313,0.156 10 false *4 2.958,0.125 3.271,0.281 0.313,0.156 10 false *5 0.5,0.75 0.813,0.906 0.313,0.156 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the compression ring ends.



c.
A337636C01
0.656,0.719 0.917,0.25 0.917,0.25 1.083,0.25 true 0.115,1.115 0.427,1.271 0.313,0.156 10 false *a 1.104,0.167 1.417,0.323 0.313,0.156 10 false *b
*a Front
*b Front Mark


Using a piston ring compressor, push the numbered piston and connecting rod assembly into the correct cylinder with the front mark of the piston facing forward.


d.

Match the numbered connecting rod cap with the correct connecting rod.


e.
A097980C08
0.719,1.042 1.167,0.271 1.167,0.271 1.302,0.271 true 1.354,0.177 1.698,0.427 0.344,0.25 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing forward.


f.

Install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.
G035198

Step 1:

Install and alternately tighten the connecting rod cap bolts of the connecting rod cap in several steps.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


iii.

Mark the front of each connecting rod cap bolt with paint.


iv.

Step 2:

Tighten the connecting rod cap bolts 90° as shown.


v.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 11.INSPECT CONNECTING ROD THRUST CLEARANCE