Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B)
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0193718 AIRBAG SYSTEM(for Type B) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type B)  B1692/81  Lost Communication with Door Side Airbag Sensor RH  B1693/81  Door Side Airbag Sensor RH Initialization Incomplete  B1697/82  Lost Communication with Door Side Airbag Sensor LH  B1698/82  Door Side Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor LH or RH is composed of the airbag sensor assembly, side airbag sensor assembly LH or RH* and door side airbag sensor LH or RH.

The side airbag sensor assembly LH or RH* and door side airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1692/81, B1693/81, B1697/82 or B1698/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH.

*: except Single Cab

DTC No. Detection Item DTC Detection Condition Trouble Area
B1692/81 Lost Communication with Door Side Airbag Sensor RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A door side airbag sensor RH malfunction.

·

A side airbag sensor assembly RH malfunction.*

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Side airbag sensor assembly RH*

·

Airbag sensor assembly


B1693/81 Door Side Airbag Sensor RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A door side airbag sensor RH malfunction.

·

A side airbag sensor assembly RH malfunction.*

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Side airbag sensor assembly RH*

·

Airbag sensor assembly


B1697/82 Lost Communication with Door Side Airbag Sensor LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

A side airbag sensor assembly LH malfunction.*

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Door side airbag sensor LH

·

Side airbag sensor assembly LH*

·

Airbag sensor assembly


B1698/82 Door Side Airbag Sensor LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

A side airbag sensor assembly LH malfunction.*

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Door side airbag sensor LH

·

Side airbag sensor assembly LH*

·

Airbag sensor assembly



*: except Single Cab

WIRING DIAGRAM

for Single Cab RH Side:
C279108E69
1.229,0.917 1.688,1.146 0.458,0.229 10 false BCR+ 1.271,2.083 1.698,2.281 0.427,0.198 10 false BCR- 5.594,2.063 6.125,2.385 0.531,0.323 10 false BBR- 5.583,0.896 6.083,1.094 0.5,0.198 10 false BBR+ 3.427,2.292 3.885,2.49 0.458,0.198 10 false BCR- 5.531,2.938 7.125,3.167 1.594,0.229 10 false Airbag Sensor Assembly 5.531,2.781 5.99,2.979 0.458,0.198 10 false N15 0.333,2.854 0.688,3.052 0.354,0.198 10 false J10 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.542,1.906 3.802,2.063 0.26,0.156 10 false 1 3.563,0.729 3.792,0.885 0.229,0.156 10 false 2 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.448,0.917 3.906,1.115 0.458,0.198 10 false JN2 3.448,2.094 3.885,2.292 0.438,0.198 10 false JN2 3.417,1.115 3.948,1.333 0.531,0.219 10 false BCR+ 5.313,0.792 5.573,0.948 0.26,0.156 10 false 8 5.313,1.969 5.573,2.125 0.26,0.156 10 false 11 0.344,3.042 2.563,3.323 2.219,0.281 10 false Door Side Airbag Sensor RH

for Single Cab LH Side:
C279108E55
1.24,0.917 1.688,1.156 0.448,0.24 10 false BCL+ 1.271,2.083 1.698,2.365 0.427,0.281 10 false BCL- 5.594,2.063 5.979,2.24 0.385,0.177 10 false BBL- 5.583,0.896 5.979,1.094 0.396,0.198 10 false BBL+ 3.427,2.292 3.885,2.49 0.458,0.198 10 false BCL- 5.531,2.938 7.135,3.188 1.604,0.25 10 false Airbag Sensor Assembly 5.531,2.781 5.99,2.979 0.458,0.198 10 false N14 0.323,2.833 0.677,3.031 0.354,0.198 10 false K10 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.583,1.906 3.844,2.063 0.26,0.156 10 false 1 3.563,0.729 3.792,0.885 0.229,0.156 10 false 2 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.448,0.917 3.906,1.115 0.458,0.198 10 false KN2 3.448,2.094 3.885,2.292 0.438,0.198 10 false KN2 3.417,1.115 3.875,1.313 0.458,0.198 10 false BCL+ 5.313,0.792 5.573,0.948 0.26,0.156 10 false 8 5.313,1.969 5.573,2.125 0.26,0.156 10 false 15 0.323,3.021 2.5,3.302 2.177,0.281 10 false Door Side Airbag Sensor LH

for except Single Cab RH Side:
C311846E35
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N15 5.427,0.99 6.01,1.438 0.583,0.448 10 false 11 5.49,0.563 6.177,0.927 0.688,0.365 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBR+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBR- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.635 1.677,1.083 0.583,0.448 10 false BBR+ 1.073,1.042 1.656,1.49 0.583,0.448 10 false BBR- 1.063,2.135 1.646,2.583 0.583,0.448 10 false BCR+ 1.094,2.781 1.677,3.229 0.583,0.448 10 false BCR- 2.25,2.354 2.833,2.802 0.583,0.448 10 false BCR+ 2.26,3.021 2.844,3.469 0.583,0.448 10 false BCR- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCR+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCR- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N13 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly RH 2.271,2.135 2.854,2.583 0.583,0.448 10 false JN2 2.271,2.802 2.854,3.25 0.583,0.448 10 false JN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false J10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor RH

for except Single Cab LH Side:
C311846E30
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N14 5.406,0.99 5.99,1.438 0.583,0.448 10 false 15 5.438,0.573 7.146,0.927 1.708,0.354 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBL+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBL- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.625 1.677,1.073 0.583,0.448 10 false BBL+ 1.104,1.052 1.688,1.5 0.583,0.448 10 false BBL- 1.094,2.135 1.677,2.583 0.583,0.448 10 false BCL+ 1.125,2.781 1.708,3.229 0.583,0.448 10 false BCL- 2.25,2.365 2.833,2.813 0.583,0.448 10 false BCL+ 2.26,3.052 2.844,3.5 0.583,0.448 10 false BCL- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCL+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCL- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N12 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly LH 2.271,2.146 2.854,2.594 0.583,0.448 10 false KN2 2.271,2.792 2.854,3.24 0.583,0.448 10 false KN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false K10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Single Cab A
except Single Cab B



A

2.CHECK DTC

B

13.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1697/82 or B1698/82 is output
DTC B1692/81 or B1693/81 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.




DTC B1697/82 or B1698/82 is output

3.CHECK CONNECTION OF CONNECTORS

DTC B1692/81 or B1693/81 is output

8.CHECK CONNECTION OF CONNECTORS

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and door side airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

4.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and door side airbag sensor LH.


b.
C208241C20
0.615,1.448 0.813,1.615 0.198,0.167 10 false *1 2.667,1.573 2.865,1.74 0.198,0.167 10 false *2 1.302,0.771 1.5,0.938 0.198,0.167 10 false *3 1.75,0.771 1.948,0.938 0.198,0.167 10 false *4
*1 Door Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Front Door Wire LH
*4 Floor Wire


Check that the connectors (on the airbag sensor assembly side and door side airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

5.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

5.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C327138C01
3.042,0.677 3.406,0.938 0.365,0.26 5.063,0.458 5.427,0.719 0.365,0.26 5.292,1.052 5.417,1.052 false 3.479,1.427 3.781,0.833 true 4.292,1.438 3.948,0.833 true 6.583,1.479 6.188,0.948 true 5.708,1.448 5.865,1.167 true 3.094,0.719 3.552,0.917 0.458,0.198 10 false K10 5.115,0.5 5.573,0.698 0.458,0.198 10 false N14 1.823,0.646 2.281,0.844 0.458,0.198 10 false A 1.469,0.875 1.927,1.073 0.458,0.198 10 false B 1.281,0.875 1.74,1.073 0.458,0.198 10 false C 1.135,0.875 1.594,1.073 0.458,0.198 10 false D 0.948,0.875 1.406,1.073 0.458,0.198 10 false E 0.573,0.656 1.031,0.854 0.458,0.198 10 false F 0.469,1.063 0.927,1.26 0.458,0.198 10 false *1 2.031,1.135 2.49,1.333 0.458,0.198 10 false *2 1.073,0.417 1.531,0.615 0.458,0.198 10 false *3 1.333,0.417 1.792,0.615 0.458,0.198 10 false *4 4.375,0.74 4.833,0.938 0.458,0.198 10 false *5 6.698,0.625 6.917,0.844 0.219,0.219 10 false *6 5.146,1 5.365,1.219 0.219,0.219 10 false *7 3.813,0.24 4.271,0.438 0.458,0.198 10 false *a 6.083,0.135 6.542,0.333 0.458,0.198 10 false *b 3.313,1.458 3.75,1.656 0.438,0.198 10 false BCL- 4.188,1.469 5.052,1.667 0.865,0.198 10 false BCL+ 5.573,1.458 6.01,1.656 0.438,0.198 10 false BBL- 6.458,1.479 7.063,1.688 0.604,0.208 10 false BBL+
*1 Door Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Front Door Wire LH *4 Floor Wire
*5 Connector E *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K10-2 (BCL+) - Body ground Ignition switch ON Below 1 V
K10-1 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBL+) and 11 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-2 (BCL+) - K10-1 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-2 (BCL+) - K10-1 (BCL-) Always 1 MΩ or higher
K10-2 (BCL+) - Body ground Always 1 MΩ or higher
K10-1 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DOOR SIDE AIRBAG SENSOR LH

NG

7.CHECK FLOOR WIRE
6.CHECK DOOR SIDE AIRBAG SENSOR LH
a.

Connect the connectors to the airbag sensor assembly.


b.
C148689C01
0.617,1.104 0.787,1.265 0.17,0.161 10 *1 2.02,1.104 2.191,1.279 0.17,0.175 10 *2
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Interchange the door side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1692/81 or B1693/81 is output
DTC B1697/82 or B1698/82 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1692/81 or B1693/81 is output

DTC B1697/82 or B1698/82 is output

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

7.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire LH.

C327148C01
3.01,0.625 3.417,0.875 0.406,0.25 5.146,0.448 5.552,0.698 0.406,0.25 5.552,1.427 5.833,1.177 true 6.74,1.458 6.188,0.979 true 3.354,1.292 3.792,0.594 true 4.333,1.333 3.938,0.583 true 5.26,1.052 5.417,1.052 true 5.219,0.49 5.677,0.688 0.458,0.198 10 false N14 3.083,0.656 3.542,0.854 0.458,0.198 10 false KN2 3.188,1.323 3.646,1.521 0.458,0.198 10 false BCL+ 4.198,1.344 4.656,1.542 0.458,0.198 10 false BCL- 5.406,1.438 5.865,1.635 0.458,0.198 10 false BBL+ 6.615,1.469 7.073,1.667 0.458,0.198 10 false BBL- 0.458,1.052 0.917,1.25 0.458,0.198 10 false *1 2.021,1.177 2.479,1.375 0.458,0.198 10 false *2 0.99,0.469 1.448,0.667 0.458,0.198 10 false *3 1.385,0.469 1.844,0.667 0.458,0.198 10 false *4 4.333,0.698 4.792,0.896 0.458,0.198 10 false *5 6.781,0.854 7.104,1.094 0.323,0.24 10 false *6 5.083,0.969 5.406,1.208 0.323,0.24 10 false *7 1.823,0.656 2.281,0.854 0.458,0.198 10 false A 1.563,0.844 2.021,1.042 0.458,0.198 10 false B 1.281,0.844 1.74,1.042 0.458,0.198 10 false C 1.146,0.844 1.604,1.042 0.458,0.198 10 false D 0.865,0.844 1.323,1.042 0.458,0.198 10 false E 0.615,0.646 1.073,0.844 0.458,0.198 10 false F 3.802,0.094 4.26,0.292 0.458,0.198 10 false *a 6.115,0.094 6.573,0.292 0.458,0.198 10 false *b
*1 Door Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Front Door Wire LH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
KN2-1 (BCL-) - Body ground Ignition switch ON Below 1 V
KN2-2 (BCL+) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 8 (BBL-) and 15 (BBL+) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
KN2-1 (BCL-) - KN2-2 (BCL+) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
KN2-1 (BCL-) - KN2-2 (BCL+) Always 1 MΩ or higher
KN2-1 (BCL-) - Body ground Always 1 MΩ or higher
KN2-2 (BCL+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and door side airbag sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

9.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and door side airbag sensor RH.


b.
C215011C02
0.677,1.719 0.99,1.875 0.313,0.156 10 false *1 2.5,1.542 2.813,1.698 0.313,0.156 10 false *2 1.323,0.979 1.635,1.135 0.313,0.156 10 false *3 1.719,0.969 2.031,1.125 0.313,0.156 10 false *4
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Front Door Wire RH
*4 Floor Wire


Check that the connectors (on the airbag sensor assembly side and door side airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

10.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

10.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C327137C04
5.052,0.813 5.427,1.073 0.375,0.26 2.969,0.688 3.344,0.948 0.375,0.26 3.396,1.26 3.781,0.823 true 4.333,1.25 3.948,0.823 true 6.604,1.448 6.375,1.177 true 5.542,1.438 6.042,0.958 true 5.125,0.854 5.583,1.052 0.458,0.198 10 false N15 6,0.125 6.458,0.323 0.458,0.198 10 false *b 6.948,0.979 7.156,1.177 0.208,0.198 10 false *7 5.385,1.448 5.823,1.698 0.438,0.25 10 false BBR+ 4.198,1.292 4.635,1.542 0.438,0.25 10 false BCR+ 3.26,1.281 3.698,1.531 0.438,0.25 10 false BCR- 3.073,0.74 3.531,0.938 0.458,0.198 10 false J10 3.802,0.24 4.26,0.438 0.458,0.198 10 false *a 0.469,1.292 0.927,1.49 0.458,0.198 10 false *1 2.073,1.125 2.531,1.323 0.458,0.198 10 false *2 1.042,0.656 1.5,0.854 0.458,0.198 10 false *3 1.323,0.656 1.781,0.854 0.458,0.198 10 false *4 4.344,0.75 4.802,0.948 0.458,0.198 10 false *5 6.646,0.563 6.854,0.76 0.208,0.198 10 false *6 6.51,1.49 6.948,1.74 0.438,0.25 10 false BBR- 1.823,0.885 2.281,1.083 0.458,0.198 10 false A 1.479,1.135 1.938,1.333 0.458,0.198 10 false B 1.271,1.135 1.729,1.333 0.458,0.198 10 false C 1.146,1.135 1.604,1.333 0.458,0.198 10 false D 0.927,1.146 1.385,1.344 0.458,0.198 10 false E 0.604,0.896 1.063,1.094 0.458,0.198 10 false F
*1 Door Side Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Front Door Wire RH *4 Floor Wire
*5 Connector E *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J10-2 (BCR+) - Body ground Ignition switch ON Below 1 V
J10-1 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-2 (BCR+) - J10-1 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-2 (BCR+) - J10-1 (BCR-) Always 1 MΩ or higher
J10-2 (BCR+) - Body ground Always 1 MΩ or higher
J10-1 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK DOOR SIDE AIRBAG SENSOR RH

NG

12.CHECK FLOOR WIRE
11.CHECK DOOR SIDE AIRBAG SENSOR RH
a.

Connect the connectors to the airbag sensor assembly.


b.
C321275C01
0.917,1.25 1.229,1.406 0.313,0.156 10 false *1 2.167,1.115 2.479,1.271 0.313,0.156 10 false *2
*1 Door Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Interchange the door side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1692/81 or B1693/81 is output
DTC B1697/82 or B1698/82 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1692/81 or B1693/81 is output

DTC B1697/82 or B1698/82 is output

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

12.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire RH.

C327149C02
5.167,0.823 5.531,1.042 0.365,0.219 3.219,0.656 3.583,0.875 0.365,0.219 6.938,1.052 6.802,1.052 false 3.542,1.396 3.917,0.656 true 4.448,1.385 4.094,0.656 true 5.583,1.427 6.052,0.938 true 6.573,1.438 6.385,1.167 true 5.229,0.844 5.688,1.042 0.458,0.198 10 false N15 3.271,0.688 3.729,0.885 0.458,0.198 10 false JN2 0.469,1.292 0.927,1.49 0.458,0.198 10 false *1 2.042,1.135 2.5,1.333 0.458,0.198 10 false *2 0.979,0.688 1.438,0.885 0.458,0.198 10 false *3 1.396,0.688 1.854,0.885 0.458,0.198 10 false *4 4.438,0.635 4.896,0.833 0.458,0.198 10 false *5 6.615,0.531 6.813,0.771 0.198,0.24 10 false *6 1.833,0.875 2.271,1.094 0.438,0.219 10 false A 1.563,1.125 2,1.344 0.438,0.219 10 false B 1.292,1.135 1.729,1.354 0.438,0.219 10 false C 1.135,1.135 1.573,1.354 0.438,0.219 10 false D 0.885,1.135 1.323,1.354 0.438,0.219 10 false E 0.594,0.885 1.031,1.104 0.438,0.219 10 false F 6.958,0.958 7.156,1.198 0.198,0.24 10 false *7 3.385,1.406 3.844,1.604 0.458,0.198 10 false BCR+ 4.313,1.417 4.771,1.615 0.458,0.198 10 false BCR- 5.385,1.438 5.844,1.635 0.458,0.198 10 false BBR+ 6.469,1.438 6.927,1.635 0.458,0.198 10 false BBR- 3.938,0.125 4.396,0.323 0.458,0.198 10 false *a 6.042,0.135 6.5,0.333 0.458,0.198 10 false *b
*1 Door Side Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Front Door Wire RH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JN2-1 (BCR-) - Body ground Ignition switch ON Below 1 V
JN2-2 (BCR+) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BCR-) - JN2-2 (BCR+) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BCR-) - JN2-2 (BCR+) Always 1 MΩ or higher
JN2-1 (BCR-) - Body ground Always 1 MΩ or higher
JN2-2 (BCR+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

13.CHECK DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1697/82 or B1698/82 is output
DTC B1692/81 or B1693/81 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.




DTC B1697/82 or B1698/82 is output

14.CHECK CONNECTION OF CONNECTORS

DTC B1692/81 or B1693/81 is output

20.CHECK CONNECTION OF CONNECTORS

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

14.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and door side airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

15.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

15.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and door side airbag sensor LH.


b.
C326607C01
0.656,1.635 0.969,1.833 0.313,0.198 10 false *1 1.521,0.833 1.833,1.031 0.313,0.198 10 false *4 2.594,1.688 2.906,1.885 0.313,0.198 10 false *3 1.771,1.625 2.083,1.823 0.313,0.198 10 false *5 1.563,2.854 1.875,3.052 0.313,0.198 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Door Side Airbag Sensor LH
*3 Airbag Sensor Assembly
*4 Floor Wire
*5 Front Door Wire LH


Check that the connectors (on the airbag sensor assembly side, side airbag sensor assembly LH side and door side airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE LH OR FLOOR WIRE

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C14
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 false 4.125,1.302 3.625,0.906 false 5.094,1.24 5.583,0.875 false 6.448,1.26 5.74,0.865 false 3.854,1.594 3.583,1.417 false 0.354,1.25 0.667,1.406 0.313,0.156 10 false *1 1.875,1.281 2.135,1.458 0.26,0.177 10 false *2 4.104,0.75 4.406,0.938 0.302,0.188 10 false *3 6.417,0.74 6.729,0.896 0.313,0.156 10 false *4 3.458,0.115 3.771,0.271 0.313,0.156 10 false *a 5.698,0.135 6.01,0.292 0.313,0.156 10 false *b 0.583,0.802 0.896,0.958 0.313,0.156 10 false F 0.906,1.021 1.219,1.177 0.313,0.156 10 false E 1.104,1.021 1.417,1.177 0.313,0.156 10 false D 1.219,1.021 1.531,1.177 0.313,0.156 10 false C 1.385,1.021 1.698,1.177 0.313,0.156 10 false B 1.74,0.792 2.052,0.948 0.313,0.156 10 false A 2.563,0.75 3.042,0.948 0.479,0.198 10 false K10 2.656,1.292 3.135,1.49 0.479,0.198 10 false BCL- 3.99,1.323 4.469,1.521 0.479,0.198 10 false BCL+ 3.896,1.552 4.167,1.729 0.271,0.177 10 false *5 4.729,0.729 5.271,0.917 0.542,0.188 10 false N12 4.927,1.281 5.406,1.479 0.479,0.198 10 false BCL+ 6.365,1.313 6.844,1.51 0.479,0.198 10 false BCL-
*1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
N12-1 (BCL+) - Body ground Always 1 MΩ or higher
N12-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

18.CHECK FLOOR WIRE
17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C214664C02
0.844,1.344 1.01,1.51 0.167,0.167 10 false *1 2.385,1.448 2.552,1.615 0.167,0.167 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1692/81 or B1693/81 is output
DTC B1697/82 or B1698/82 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.



DTC B1692/81 or B1693/81 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

DTC B1697/82 or B1698/82 is output

19.CHECK DOOR SIDE AIRBAG SENSOR LH

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

18.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire LH.

C279670C15
5.042,0.667 5.365,0.906 0.323,0.24 2.844,0.615 3.24,0.833 0.396,0.219 5.396,1.25 5.813,0.833 true 6.406,1.24 5.917,0.823 true 4.292,1.104 3.813,0.646 true 3.177,1.125 3.604,0.656 true 3.313,1.51 3.573,1.385 false 0.917,0.75 0.917,0.25 0.917,0.25 1.083,0.25 false 1.333,0.833 1.333,1.333 1.333,1.333 1.167,1.333 false 1.729,0.688 1.885,0.885 0.156,0.198 10 false A 1.385,0.927 1.542,1.125 0.156,0.198 10 false B 1.094,0.938 1.25,1.135 0.156,0.198 10 false C 0.906,0.938 1.063,1.135 0.156,0.198 10 false D 0.698,0.938 0.854,1.135 0.156,0.198 10 false E 0.365,0.677 0.521,0.875 0.156,0.198 10 false F 0.365,1.125 0.594,1.323 0.229,0.198 10 false *1 1.635,1.156 1.865,1.354 0.229,0.198 10 false *2 1.115,0.188 1.344,0.385 0.229,0.198 10 false *3 0.958,1.25 1.188,1.448 0.229,0.198 10 false *4 3.594,0.125 3.823,0.323 0.229,0.198 10 false *a 5.854,0.146 6.083,0.344 0.229,0.198 10 false *b 6.615,0.677 6.844,0.875 0.229,0.198 10 false *6 4.25,0.667 4.479,0.865 0.229,0.198 10 false *5 2.906,0.646 3.229,0.833 0.323,0.188 10 false KN2 5.083,0.708 5.521,0.927 0.438,0.219 10 false N12 3.094,1.469 3.323,1.667 0.229,0.198 10 false *7 4.198,1.146 4.75,1.323 0.552,0.177 10 false BCL- 5.094,1.281 5.646,1.458 0.552,0.177 10 false BCL+ 2.958,1.167 3.51,1.344 0.552,0.177 10 false BCL+ 6.323,1.26 6.875,1.438 0.552,0.177 10 false BCL-
*1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 1 (BCL-) and 2 (BCL+) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
N12-1 (BCL+) - Body ground Always 1 MΩ or higher
N12-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

19.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Interchange the door side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1692/81 or B1693/81 is output
DTC B1697/82 or B1698/82 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1692/81 or B1693/81 is output

DTC B1697/82 or B1698/82 is output

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

20.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and door side airbag sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

21.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

21.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and door side airbag sensor RH.


b.
C279112C03
0.594,2.021 0.906,2.177 0.313,0.156 10 false *1 1.542,3.198 1.854,3.354 0.313,0.156 10 false *2 2.51,1.729 2.823,1.885 0.313,0.156 10 false *3 1.469,1.188 1.781,1.344 0.313,0.156 10 false *4 1.75,1.979 2.063,2.135 0.313,0.156 10 false *5
*1 Side Airbag Sensor Assembly RH
*2 Door Side Airbag Sensor RH
*3 Airbag Sensor Assembly
*4 Floor Wire
*5 Front Door Wire RH


Check that the connectors (on the airbag sensor assembly side, side airbag sensor assembly RH side and door side airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

22.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE RH OR FLOOR WIRE

22.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C16
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 true 4.125,1.302 3.625,0.906 true 5.094,1.24 5.583,0.875 true 6.448,1.26 5.74,0.865 true 3.854,1.594 3.583,1.417 true 0.354,1.25 0.667,1.406 0.313,0.156 10 false *1 1.875,1.281 2.135,1.458 0.26,0.177 10 false *2 4.104,0.75 4.406,0.938 0.302,0.188 10 false *3 6.417,0.74 6.729,0.896 0.313,0.156 10 false *4 3.458,0.115 3.771,0.271 0.313,0.156 10 false *a 5.698,0.135 6.01,0.292 0.313,0.156 10 false *b 0.583,0.802 0.896,0.958 0.313,0.156 10 false F 0.906,1.021 1.219,1.177 0.313,0.156 10 false E 1.104,1.021 1.417,1.177 0.313,0.156 10 false D 1.219,1.021 1.531,1.177 0.313,0.156 10 false C 1.385,1.021 1.698,1.177 0.313,0.156 10 false B 1.74,0.792 2.052,0.948 0.313,0.156 10 false A 2.583,0.75 2.844,0.927 0.26,0.177 10 false J10 2.656,1.281 3.135,1.479 0.479,0.198 10 false BCR- 3.99,1.323 4.469,1.521 0.479,0.198 10 false BCR+ 3.896,1.552 4.167,1.729 0.271,0.177 10 false *5 4.74,0.729 5.094,0.906 0.354,0.177 10 false N13 4.906,1.313 5.385,1.51 0.479,0.198 10 false BCR+ 6.365,1.313 6.844,1.51 0.479,0.198 10 false BCR-
*1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
N13-1 (BCR+) - Body ground Always 1 MΩ or higher
N13-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

24.CHECK FLOOR WIRE
23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C171812C05
0.666,1.37 0.817,1.54 0.152,0.17 10 *1 1.801,1.37 1.993,1.54 0.192,0.17 10 *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1697/82 or B1698/82 is output
DTC B1692/81 or B1693/81 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B1697/82 or B1698/82 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

DTC B1692/81 or B1693/81 is output

25.CHECK DOOR SIDE AIRBAG SENSOR RH

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

24.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire RH.

C279670C17
5.042,0.667 5.365,0.906 0.323,0.24 2.885,0.635 3.24,0.833 0.354,0.198 5.396,1.25 5.813,0.833 true 6.438,1.281 5.917,0.823 true 4.313,1.063 3.813,0.635 true 3.125,1.073 3.604,0.635 true 3.208,1.531 3.573,1.385 true 0.917,0.729 0.917,0.25 0.917,0.25 1.083,0.25 true 1.333,0.833 1.333,1.333 1.333,1.333 1.167,1.333 true 1.729,0.688 1.885,0.885 0.156,0.198 10 false A 1.385,0.927 1.542,1.125 0.156,0.198 10 false B 1.094,0.938 1.25,1.135 0.156,0.198 10 false C 0.906,0.938 1.063,1.135 0.156,0.198 10 false D 0.698,0.938 0.854,1.135 0.156,0.198 10 false E 0.365,0.677 0.521,0.875 0.156,0.198 10 false F 0.365,1.125 0.594,1.323 0.229,0.198 10 false *1 1.646,1.156 1.875,1.354 0.229,0.198 10 false *2 1.115,0.188 1.344,0.385 0.229,0.198 10 false *3 0.958,1.25 1.188,1.448 0.229,0.198 10 false *4 3.594,0.125 3.823,0.323 0.229,0.198 10 false *a 5.854,0.146 6.083,0.344 0.229,0.198 10 false *b 6.615,0.677 6.844,0.875 0.229,0.198 10 false *6 4.25,0.667 4.479,0.865 0.229,0.198 10 false *5 2.948,0.656 3.271,0.844 0.323,0.188 10 false JN2 5.104,0.708 5.396,0.906 0.292,0.198 10 false N13 2.958,1.469 3.188,1.667 0.229,0.198 10 false *7 2.708,1.042 3.26,1.219 0.552,0.177 10 false BCR+ 5.094,1.281 5.646,1.458 0.552,0.177 10 false BCR+ 4.344,1.021 4.896,1.198 0.552,0.177 10 false BCR- 6.406,1.302 6.958,1.479 0.552,0.177 10 false BCR-
*1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
N13-1 (BCR+) - Body ground Always 1 MΩ or higher
N13-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

25.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor LH
*2 Side Airbag Sensor Assembly RH


Interchange the door side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1697/82 or B1698/82 is output
DTC B1692/81 or B1693/81 is output
DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output


HINT:

Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1697/82 or B1698/82 is output

DTC B1692/81 or B1693/81 is output

DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output