Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B)
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0193718 AIRBAG SYSTEM(for Type B) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type B)  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor LH or RH is composed of the airbag sensor assembly, door side airbag sensor LH or RH and side airbag sensor assembly LH or RH.

The side airbag sensor assembly LH or RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1633/81 or B1638/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Side airbag sensor assembly RH

·

Airbag sensor assembly


B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A side airbag sensor assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Side airbag sensor assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

for RH Side:
C311846E32
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N15 5.427,0.99 6.01,1.438 0.583,0.448 10 false 11 5.49,0.563 6.177,0.927 0.688,0.365 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBR+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBR- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.635 1.677,1.083 0.583,0.448 10 false BBR+ 1.073,1.042 1.656,1.49 0.583,0.448 10 false BBR- 1.063,2.135 1.646,2.583 0.583,0.448 10 false BCR+ 1.094,2.781 1.677,3.229 0.583,0.448 10 false BCR- 2.25,2.354 2.833,2.802 0.583,0.448 10 false BCR+ 2.26,3.021 2.844,3.469 0.583,0.448 10 false BCR- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCR+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCR- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N13 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly RH 2.271,2.135 2.854,2.583 0.583,0.448 10 false JN2 2.271,2.802 2.854,3.25 0.583,0.448 10 false JN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false J10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor RH

for LH Side:
C311846E24
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N14 5.406,0.99 5.99,1.438 0.583,0.448 10 false 15 5.438,0.573 7.146,0.927 1.708,0.354 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBL+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBL- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.625 1.677,1.073 0.583,0.448 10 false BBL+ 1.104,1.052 1.688,1.5 0.583,0.448 10 false BBL- 1.094,2.135 1.677,2.583 0.583,0.448 10 false BCL+ 1.125,2.781 1.708,3.229 0.583,0.448 10 false BCL- 2.25,2.365 2.833,2.813 0.583,0.448 10 false BCL+ 2.26,3.052 2.844,3.5 0.583,0.448 10 false BCL- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCL+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCL- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N12 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly LH 2.271,2.146 2.854,2.594 0.583,0.448 10 false KN2 2.271,2.792 2.854,3.24 0.583,0.448 10 false KN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false K10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK PAST DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Proceed to
DTC B1632/81 and B1637/82 are not output
DTC B1632/81 and B1637/82 are output



DTC B1632/81 and B1637/82 are not output

2.CHECK DTC

DTC B1632/81 and B1637/82 are output

2.CHECK DTC
a.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. The malfunctioning area can be identified by turning the ignition switch off and then to ON again.



b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633/81 is output
DTC B1638/82 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.




DTC B1633/81 is output

3.CHECK CONNECTION OF CONNECTORS

DTC B1638/82 is output

7.CHECK CONNECTION OF CONNECTORS

DTC B1633/81 and B1638/82 are not output

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

4.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.


b.
C208245C11
0.313,1.75 0.625,1.906 0.313,0.156 10 *1 2.115,1.604 2.427,1.76 0.313,0.156 10 *2 1.521,1.021 1.833,1.177 0.313,0.156 10 *3
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

5.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C274528C02
5.042,0.698 5.396,0.969 0.354,0.271 2.833,0.688 3.188,0.958 0.354,0.271 6.792,1.052 6.906,1.052 false 4.26,1.26 4,0.865 true 3.698,1.271 3.896,0.875 true 6.594,1.51 6.365,1.188 true 5.875,1.531 6.042,0.969 true 0.427,1.302 0.74,1.458 0.313,0.156 10 false *1 1.99,1.167 2.302,1.323 0.313,0.156 10 false *2 1.156,0.729 1.469,0.885 0.313,0.156 10 false *3 4.448,0.729 4.76,0.885 0.313,0.156 10 false *4 6.677,0.563 6.906,0.771 0.229,0.208 10 false *5 6.948,0.979 7.156,1.177 0.208,0.198 10 false *6 3.781,0.25 4.094,0.406 0.313,0.156 10 false *a 5.99,0.115 6.302,0.271 0.313,0.156 10 false *b 2.885,0.75 3.167,0.948 0.281,0.198 10 false N13 5.094,0.75 5.427,0.938 0.333,0.188 10 false N15 0.594,0.896 0.75,1.094 0.156,0.198 10 false D 0.948,1.104 1.104,1.302 0.156,0.198 10 false C 1.458,1.115 1.635,1.302 0.177,0.188 10 false B 1.844,0.906 2.156,1.063 0.313,0.156 10 false A 3.531,1.302 3.927,1.51 0.396,0.208 10 false BBR- 4.146,1.292 4.635,1.5 0.49,0.208 10 false BBR+ 5.625,1.552 6.115,1.781 0.49,0.229 10 false BBR+ 6.521,1.552 6.948,1.771 0.427,0.219 10 false BBR-
*1 Side Airbag Sensor Assembly RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-4 (BBR+) - Body ground Ignition switch ON Below 1 V
N13-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-4 (BBR+) - N13-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-4 (BBR+) - N13-3 (BBR-) Always 1 MΩ or higher
N13-4 (BBR+) - Body ground Always 1 MΩ or higher
N13-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C171812C26
0.896,1.271 1.208,1.427 0.313,0.156 10 *1 2.125,1.125 2.438,1.281 0.313,0.156 10 *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1638/82 is output
DTC B1633/81 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B1638/82 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

DTC B1633/81 is output

DTC B1633/81 and B1638/82 are not output

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

8.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly LH.


b.
C326156C01
0.656,1.458 0.969,1.615 0.313,0.156 10 false *1 2.615,1.531 2.927,1.688 0.313,0.156 10 false *2 1.458,0.688 1.771,0.844 0.313,0.156 10 false *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

9.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C274527C03
2.844,0.729 3.188,0.99 0.344,0.26 5.24,0.323 5.583,0.583 0.344,0.26 3.563,1.385 3.896,0.875 true 5.292,1.073 5.427,1.073 false 4.26,1.375 4.01,0.865 true 6.365,1.521 6.188,0.958 true 5.677,1.542 5.865,1.188 true 0.438,1.073 0.75,1.229 0.313,0.156 10 false *1 1.99,1.156 2.302,1.313 0.313,0.156 10 false *2 1.167,0.49 1.479,0.646 0.313,0.156 10 false *3 4.469,0.729 4.781,0.885 0.313,0.156 10 false *4 6.708,0.615 7.021,0.771 0.313,0.156 10 false *5 5.135,0.99 5.448,1.146 0.313,0.156 10 false *6 3.781,0.26 4.094,0.417 0.313,0.156 10 false *a 6.083,0.146 6.396,0.302 0.313,0.156 10 false *b 0.583,0.646 0.813,0.844 0.229,0.198 10 false D 0.948,0.865 1.188,1.031 0.24,0.167 10 false C 1.458,0.875 1.688,1.052 0.229,0.177 10 false B 1.844,0.656 2.052,0.833 0.208,0.177 10 false A 2.896,0.771 3.24,0.958 0.344,0.188 10 false N12 5.292,0.375 5.635,0.563 0.344,0.188 10 false N14 3.396,1.406 3.771,1.625 0.375,0.219 10 false BBL- 4.177,1.406 4.552,1.625 0.375,0.219 10 false BBL+ 5.51,1.552 5.885,1.771 0.375,0.219 10 false BBL- 6.333,1.552 6.76,1.74 0.427,0.188 10 false BBL+
*1 Side Airbag Sensor Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-4 (BBL+) - Body ground Ignition switch ON Below 1 V
N12-3 (BBL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-4 (BBL+) - N12-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-4 (BBL+) - N12-3 (BBL-) Always 1 MΩ or higher
N12-4 (BBL+) - Body ground Always 1 MΩ or higher
N12-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

10.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C326158C01
1.052,1.458 1.365,1.615 0.313,0.156 10 false *1 2.365,1.573 2.677,1.729 0.313,0.156 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633/81 is output
DTC B1638/82 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.



DTC B1633/81 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

DTC B1638/82 is output

DTC B1633/81 and B1638/82 are not output