Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B)
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0193718 AIRBAG SYSTEM(for Type B) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type B)  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1643/81  Side Satellite Sensor Bus RH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor LH or RH is composed of the airbag sensor assembly, side airbag sensor assembly LH or RH and door side airbag sensor LH or RH.

The door side airbag sensor LH or RH and side airbag sensor assembly LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1642/81, B1643/81, B1647/82 or B1648/82 is stored when a malfunction is detected in the circuit for the side satellite sensor bus LH or RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1642/81 Lost Communication with Side Satellite Sensor Bus RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus RH for 2 seconds.

·

A door side airbag sensor RH malfunction.

·

A side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Side airbag sensor assembly RH

·

Airbag sensor assembly


B1643/81 Side Satellite Sensor Bus RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus RH for 2 seconds.

·

A door side airbag sensor RH malfunction.

·

A side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Door side airbag sensor RH

·

Side airbag sensor assembly RH

·

Airbag sensor assembly


B1647/82 Lost Communication with Side Satellite Sensor Bus LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

A side airbag sensor assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Door side airbag sensor LH

·

Side airbag sensor assembly LH

·

Airbag sensor assembly


B1648/82 Side Satellite Sensor Bus LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.

·

A door side airbag sensor LH malfunction.

·

A side airbag sensor assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

Door side airbag sensor LH

·

Side airbag sensor assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

for RH Side:
C311846E33
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N15 5.427,0.99 6.01,1.438 0.583,0.448 10 false 11 5.49,0.563 6.177,0.927 0.688,0.365 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBR+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBR- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.635 1.677,1.083 0.583,0.448 10 false BBR+ 1.073,1.042 1.656,1.49 0.583,0.448 10 false BBR- 1.063,2.135 1.646,2.583 0.583,0.448 10 false BCR+ 1.094,2.781 1.677,3.229 0.583,0.448 10 false BCR- 2.25,2.354 2.833,2.802 0.583,0.448 10 false BCR+ 2.26,3.021 2.844,3.469 0.583,0.448 10 false BCR- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCR+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCR- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N13 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly RH 2.271,2.135 2.854,2.583 0.583,0.448 10 false JN2 2.271,2.802 2.854,3.25 0.583,0.448 10 false JN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false J10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor RH

for LH Side:
C311846E26
5.438,2.01 7.146,2.365 1.708,0.354 10 false Airbag Sensor Assembly 5.427,1.854 7.135,2.208 1.708,0.354 10 false N14 5.406,0.99 5.99,1.438 0.583,0.448 10 false 15 5.438,0.573 7.146,0.927 1.708,0.354 10 false 8 5.729,0.646 6.313,1.094 0.583,0.448 10 false BBL+ 5.729,1.094 6.313,1.542 0.583,0.448 10 false BBL- 1.542,0.573 3.25,0.927 1.708,0.354 10 false 4 1.094,0.625 1.677,1.073 0.583,0.448 10 false BBL+ 1.104,1.052 1.688,1.5 0.583,0.448 10 false BBL- 1.094,2.135 1.677,2.583 0.583,0.448 10 false BCL+ 1.125,2.781 1.708,3.229 0.583,0.448 10 false BCL- 2.25,2.365 2.833,2.813 0.583,0.448 10 false BCL+ 2.26,3.052 2.844,3.5 0.583,0.448 10 false BCL- 3.167,2.146 3.75,2.594 0.583,0.448 10 false BCL+ 3.167,2.813 3.75,3.26 0.583,0.448 10 false BCL- 0.146,3.052 1.854,3.406 1.708,0.354 10 false N12 0.146,3.208 1.99,3.531 1.844,0.323 10 false Side Airbag Sensor Assembly LH 2.271,2.146 2.854,2.594 0.583,0.448 10 false KN2 2.271,2.792 2.854,3.24 0.583,0.448 10 false KN2 2.344,1.969 4.052,2.323 1.708,0.354 10 false 2 2.354,2.635 4.063,2.99 1.708,0.354 10 false 1 1.552,0.99 3.26,1.344 1.708,0.354 10 false 3 2.99,2.073 4.698,2.427 1.708,0.354 10 false 2 1.552,2.729 3.26,3.083 1.708,0.354 10 false 2 1.563,2.063 3.271,2.417 1.708,0.354 10 false 1 2.99,2.719 4.698,3.073 1.708,0.354 10 false 1 2.958,3.073 4.667,3.427 1.708,0.354 10 false K10 2.958,3.24 5.531,3.51 2.573,0.271 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 or B1643/81 is output
DTC B1647/82 or B1648/82 is output
DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output


HINT:

Codes other than DTC B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.




DTC B1642/81 or B1643/81 is output

2.CHECK CONNECTION OF CONNECTORS

DTC B1647/82 or B1648/82 is output

11.CHECK CONNECTION OF CONNECTORS

DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.


b.
C208245C11
0.313,1.75 0.625,1.906 0.313,0.156 10 *1 2.115,1.604 2.427,1.76 0.313,0.156 10 *2 1.521,1.021 1.833,1.177 0.313,0.156 10 *3
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C279114C04
2.865,0.656 3.25,0.875 0.385,0.219 5,0.635 5.385,0.854 0.385,0.219 3.594,1.198 4.01,0.781 true 4.479,1.219 4.146,0.781 true 6.51,1.479 6.385,1.115 true 5.448,1.385 6.073,0.917 true 6.75,0.958 6.615,0.958 false 0.563,1.271 0.875,1.427 0.313,0.156 10 false *1 2.052,1.156 2.365,1.313 0.313,0.156 10 false *2 1.25,0.635 1.563,0.792 0.313,0.156 10 false *3 4.604,0.615 4.917,0.771 0.313,0.156 10 false *4 6.677,0.302 6.99,0.458 0.313,0.156 10 false *5 6.792,0.885 7.052,1.083 0.26,0.198 10 false *6 3.875,0.135 4.188,0.292 0.313,0.156 10 false *a 5.958,0.094 6.271,0.25 0.313,0.156 10 false *b 0.656,0.833 0.875,1.021 0.219,0.188 10 false D 1.031,1.063 1.25,1.25 0.219,0.188 10 false C 1.542,1.063 1.76,1.25 0.219,0.188 10 false B 1.917,0.833 2.135,1.021 0.219,0.188 10 false A 2.948,0.688 3.26,0.844 0.313,0.156 10 false N13 5.083,0.667 5.396,0.823 0.313,0.156 10 false N15 3.354,1.229 3.813,1.427 0.458,0.198 10 false BBR- 4.344,1.26 4.802,1.458 0.458,0.198 10 false BBR+ 5.156,1.417 5.615,1.615 0.458,0.198 10 false BBR+ 6.427,1.5 6.885,1.698 0.458,0.198 10 false BBR-
*1 Side Airbag Sensor Assembly RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-4 (BBR+) - Body ground Ignition switch ON Below 1 V
N13-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-4 (BBR+) - N13-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-4 (BBR+) - N13-3 (BBR-) Always 1 MΩ or higher
N13-4 (BBR+) - Body ground Always 1 MΩ or higher
N13-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTION OF CONNECTOR

NG

9.CHECK FLOOR WIRE
5.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the door side airbag sensor RH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

6.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

6.CHECK CONNECTOR
a.

Disconnect the connector from the door side airbag sensor RH.


b.
C306644C07
0.604,1.5 0.917,1.656 0.313,0.156 10 false *1 2.604,1.5 2.917,1.656 0.313,0.156 10 false *2 1.417,1.25 1.729,1.406 0.313,0.156 10 false *3 1.854,1.25 2.167,1.406 0.313,0.156 10 false *4
*1 Door Side Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire


Check that the connector (on the door side airbag sensor RH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

7.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

The connector is deformed or damaged

REPLACE FRONT DOOR WIRE RH

7.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C17
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 false 4.125,1.302 3.625,0.906 false 5.094,1.24 5.583,0.875 false 6.448,1.26 5.74,0.865 false 3.854,1.594 3.583,1.417 false 0.354,1.25 0.667,1.406 0.313,0.156 10 false *1 1.875,1.281 2.135,1.458 0.26,0.177 10 false *2 4.104,0.75 4.406,0.938 0.302,0.188 10 false *3 6.417,0.74 6.729,0.896 0.313,0.156 10 false *4 3.458,0.115 3.771,0.271 0.313,0.156 10 false *a 5.698,0.135 6.01,0.292 0.313,0.156 10 false *b 0.583,0.802 0.896,0.958 0.313,0.156 10 false F 0.906,1.021 1.219,1.177 0.313,0.156 10 false E 1.104,1.021 1.417,1.177 0.313,0.156 10 false D 1.219,1.021 1.531,1.177 0.313,0.156 10 false C 1.385,1.021 1.698,1.177 0.313,0.156 10 false B 1.74,0.792 2.052,0.948 0.313,0.156 10 false A 2.583,0.76 3.031,0.958 0.448,0.198 10 false J10 2.573,1.302 3.052,1.5 0.479,0.198 10 false BCR- 3.99,1.323 4.469,1.521 0.479,0.198 10 false BCR+ 3.896,1.552 4.167,1.729 0.271,0.177 10 false *5 4.729,0.729 5.292,0.99 0.563,0.26 10 false N13 4.906,1.313 5.385,1.51 0.479,0.198 10 false BCR+ 6.365,1.313 6.844,1.51 0.479,0.198 10 false BCR- 0.969,0.573 1.281,0.729 0.313,0.156 10 false *6 1.26,0.573 1.573,0.729 0.313,0.156 10 false *7
*1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
*3 Connector E *4 Connector B
*5 Service Wire *6 Front Door Wire RH
*7 Floor Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
N13-1 (BCR+) - Body ground Always 1 MΩ or higher
N13-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

9.CHECK FLOOR WIRE
8.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C171812C26
0.896,1.271 1.208,1.427 0.313,0.156 10 *1 2.125,1.125 2.438,1.281 0.313,0.156 10 *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1647/82 or B1648/82 is output
DTC B1642/81 or B1643/81 is output
DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output


HINT:

Codes other than DTC B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B1647/82 or B1648/82 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

DTC B1642/81 or B1643/81 is output

10.CHECK DOOR SIDE AIRBAG SENSOR RH

DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output

9.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire RH.

C279670C11
5.042,0.667 5.365,0.906 0.323,0.24 2.885,0.635 3.24,0.833 0.354,0.198 5.396,1.25 5.813,0.833 false 6.406,1.24 5.917,0.823 false 4.292,1.104 3.792,0.677 false 3.177,1.125 3.656,0.688 false 3.208,1.531 3.573,1.385 false 0.917,0.75 0.917,0.25 0.917,0.25 1.083,0.25 false 1.333,0.833 1.333,1.333 1.333,1.333 1.167,1.333 false 1.729,0.688 1.885,0.885 0.156,0.198 10 false A 1.385,0.927 1.542,1.125 0.156,0.198 10 false B 1.094,0.938 1.25,1.135 0.156,0.198 10 false C 0.906,0.938 1.063,1.135 0.156,0.198 10 false D 0.698,0.938 0.854,1.135 0.156,0.198 10 false E 0.365,0.677 0.521,0.875 0.156,0.198 10 false F 0.365,1.125 0.594,1.323 0.229,0.198 10 false *1 1.635,1.156 1.865,1.354 0.229,0.198 10 false *2 1.115,0.188 1.344,0.385 0.229,0.198 10 false *3 0.958,1.25 1.188,1.448 0.229,0.198 10 false *4 3.594,0.125 3.823,0.323 0.229,0.198 10 false *a 5.854,0.146 6.083,0.344 0.229,0.198 10 false *b 6.615,0.677 6.844,0.875 0.229,0.198 10 false *6 4.25,0.667 4.479,0.865 0.229,0.198 10 false *5 2.948,0.656 3.271,0.844 0.323,0.188 10 false JN2 5.094,0.698 5.385,0.896 0.292,0.198 10 false N13 2.958,1.469 3.188,1.667 0.229,0.198 10 false *7 2.708,1.042 3.26,1.219 0.552,0.177 10 false BCR+ 5.094,1.281 5.646,1.458 0.552,0.177 10 false BCR+ 4.344,1.01 4.896,1.188 0.552,0.177 10 false BCR- 6.323,1.26 6.875,1.438 0.552,0.177 10 false BCR-
*1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
N13-1 (BCR+) - Body ground Always 1 MΩ or higher
N13-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

10.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor LH
*2 Side Airbag Sensor Assembly RH


Interchange the door side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1647/82 or B1648/82 is output
DTC B1642/81 or B1643/81 is output
DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output


HINT:

Codes other than DTC B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1647/82 or B1648/82 is output

DTC B1642/81 or B1643/81 is output

DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output

11.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

12.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

12.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and door side airbag sensor LH.


b.
C326156C01
0.656,1.458 0.969,1.615 0.313,0.156 10 false *1 2.615,1.531 2.927,1.688 0.313,0.156 10 false *2 1.458,0.688 1.771,0.844 0.313,0.156 10 false *3
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

13.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

13.CHECK FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C279113C04
2.771,0.677 3.104,0.896 0.333,0.219 4.927,0.698 5.26,0.917 0.333,0.219 3.417,1.281 3.917,0.875 true 4.26,1.281 4.01,0.854 true 6.813,1.385 6.146,0.958 true 5.271,1.167 5.427,1.167 false 5.604,1.448 5.823,1.177 true 0.469,1.104 0.781,1.26 0.313,0.156 10 false *1 1.969,1.177 2.281,1.333 0.313,0.156 10 false *2 1.177,0.469 1.49,0.625 0.313,0.156 10 false *3 4.448,0.688 4.76,0.844 0.313,0.156 10 false *4 6.813,0.646 7.125,0.802 0.313,0.156 10 false *5 5.104,1.094 5.417,1.25 0.313,0.156 10 false *6 3.74,0.177 4.052,0.333 0.313,0.156 10 false *a 6.052,0.104 6.365,0.26 0.313,0.156 10 false *b 0.552,0.667 0.729,0.844 0.177,0.177 10 false D 0.958,0.896 1.135,1.073 0.177,0.177 10 false C 1.458,0.896 1.635,1.073 0.177,0.177 10 false B 1.833,0.646 2.01,0.823 0.177,0.177 10 false A 2.823,0.719 3.135,0.875 0.313,0.156 10 false N12 3.271,1.333 3.802,1.594 0.531,0.26 10 false BBL- 4.167,1.323 4.708,1.521 0.542,0.198 10 false BBL+ 6.667,1.438 7.125,1.646 0.458,0.208 10 false BBL+ 5.323,1.51 5.771,1.698 0.448,0.188 10 false BBL- 4.969,0.719 5.281,0.875 0.313,0.156 10 false N14
*1 Side Airbag Sensor Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-4 (BBL+) - Body ground Ignition switch ON Below 1 V
N12-3 (BBL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 4 (BBL+) and 3 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-4 (BBL+) - N12-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-4 (BBL+) - N12-3 (BBL-) Always 1 MΩ or higher
N12-4 (BBL+) - Body ground Always 1 MΩ or higher
N12-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CONNECTION OF CONNECTOR

NG

REPLACE FLOOR WIRE

14.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the door side airbag sensor LH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

15.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

15.CHECK CONNECTOR
a.

Disconnect the connector from the door side airbag sensor LH.


b.
C306644C07
0.604,1.5 0.917,1.656 0.313,0.156 10 false *1 2.604,1.5 2.917,1.656 0.313,0.156 10 false *2 1.417,1.25 1.729,1.406 0.313,0.156 10 false *3 1.854,1.25 2.167,1.406 0.313,0.156 10 false *4
*1 Door Side Airbag Sensor LH
*2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire


Check that the connector (on the door side airbag sensor LH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT

The connector is deformed or damaged

REPLACE FRONT DOOR WIRE LH

16.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256270C13
2.49,0.719 2.865,0.927 0.375,0.208 4.667,0.698 5.042,0.906 0.375,0.208 2.958,1.271 3.448,0.906 false 4.125,1.302 3.625,0.906 false 5.094,1.24 5.583,0.875 false 6.448,1.26 5.74,0.865 false 3.854,1.594 3.583,1.417 false 0.354,1.25 0.667,1.406 0.313,0.156 10 false *1 1.875,1.281 2.135,1.458 0.26,0.177 10 false *2 4.104,0.75 4.406,0.938 0.302,0.188 10 false *3 6.417,0.74 6.729,0.896 0.313,0.156 10 false *4 3.458,0.115 3.771,0.271 0.313,0.156 10 false *a 5.698,0.135 6.01,0.292 0.313,0.156 10 false *b 0.583,0.802 0.896,0.958 0.313,0.156 10 false F 0.906,1.021 1.219,1.177 0.313,0.156 10 false E 1.104,1.021 1.417,1.177 0.313,0.156 10 false D 1.219,1.021 1.531,1.177 0.313,0.156 10 false C 1.385,1.021 1.698,1.177 0.313,0.156 10 false B 1.74,0.792 2.052,0.948 0.313,0.156 10 false A 2.573,0.74 3.125,0.969 0.552,0.229 10 false K10 2.688,1.302 3.167,1.5 0.479,0.198 10 false BCL- 3.99,1.323 4.469,1.521 0.479,0.198 10 false BCL+ 3.896,1.552 4.167,1.729 0.271,0.177 10 false *5 4.75,0.74 5.281,0.948 0.531,0.208 10 false N12 4.896,1.26 5.375,1.458 0.479,0.198 10 false BCL+ 6.365,1.313 6.844,1.51 0.479,0.198 10 false BCL- 0.979,0.552 1.292,0.708 0.313,0.156 10 false *6 1.26,0.563 1.573,0.719 0.313,0.156 10 false *7
*1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
*3 Connector E *4 Connector B
*5 Service Wire *6 Front Door Wire LH
*7 Floor Wire - -
*a Front view of wire harness connector
(to Door Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector E.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
N12-1 (BCL+) - Body ground Always 1 MΩ or higher
N12-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

18.CHECK FLOOR WIRE
17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C157773C05
0.979,1.281 1.292,1.438 0.313,0.156 10 false *1 2.146,1.396 2.458,1.552 0.313,0.156 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 or B1643/81 is output
DTC B1647/82 or B1648/82 is output
DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output


HINT:

Codes other than DTC B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.



DTC B1642/81 or B1643/81 is output

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

DTC B1647/82 or B1648/82 is output

19.CHECK DOOR SIDE AIRBAG SENSOR LH

DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output

18.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front door wire LH.

C279670C12
5.042,0.667 5.365,0.906 0.323,0.24 2.885,0.635 3.24,0.833 0.354,0.198 5.396,1.25 5.813,0.833 true 6.406,1.24 5.917,0.823 true 4.292,1.104 3.833,0.656 true 3.177,1.125 3.615,0.677 true 3.208,1.531 3.573,1.385 false 0.917,0.75 0.917,0.25 0.917,0.25 1.083,0.25 false 1.333,0.833 1.333,1.333 1.333,1.333 1.167,1.333 false 1.729,0.688 1.885,0.885 0.156,0.198 10 false A 1.385,0.927 1.542,1.125 0.156,0.198 10 false B 1.094,0.938 1.25,1.135 0.156,0.198 10 false C 0.906,0.938 1.063,1.135 0.156,0.198 10 false D 0.698,0.938 0.854,1.135 0.156,0.198 10 false E 0.365,0.677 0.521,0.875 0.156,0.198 10 false F 0.365,1.125 0.594,1.323 0.229,0.198 10 false *1 1.635,1.156 1.865,1.354 0.229,0.198 10 false *2 1.115,0.188 1.344,0.385 0.229,0.198 10 false *3 0.958,1.25 1.188,1.448 0.229,0.198 10 false *4 3.594,0.125 3.823,0.323 0.229,0.198 10 false *a 5.854,0.146 6.083,0.344 0.229,0.198 10 false *b 6.615,0.677 6.844,0.875 0.229,0.198 10 false *6 4.25,0.667 4.479,0.865 0.229,0.198 10 false *5 2.927,0.667 3.25,0.854 0.323,0.188 10 false KN2 5.083,0.698 5.438,0.896 0.354,0.198 10 false N12 2.958,1.469 3.188,1.667 0.229,0.198 10 false *7 2.781,1.052 3.333,1.229 0.552,0.177 10 false BCL+ 5.094,1.281 5.646,1.458 0.552,0.177 10 false BCL+ 4.354,1.021 4.906,1.198 0.552,0.177 10 false BCL- 6.323,1.26 6.875,1.438 0.552,0.177 10 false BCL-
*1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH *4 Floor Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω



i.

Disconnect the service wire from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
N12-1 (BCL+) - Body ground Always 1 MΩ or higher
N12-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE

19.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C171828C15
0.688,1.333 0.854,1.49 0.167,0.156 10 *1 2.365,1.323 2.531,1.49 0.167,0.167 10 *2
*1 Door Side Airbag Sensor RH
*2 Side Airbag Sensor Assembly LH


Interchange the door side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1642/81 or B1643/81 is output
DTC B1647/82 or B1648/82 is output
DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output


HINT:

Codes other than DTC B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1642/81 or B1643/81 is output

DTC B1647/82 or B1648/82 is output

DTC B1642/81, B1643/81, B1647/82 and B1648/82 are not output