Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B)
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0193718 AIRBAG SYSTEM(for Type B) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type B)  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The front side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1825/56 Short in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front side squib LH circuit during the primary check.

·

A front seat airbag assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly LH

·

Airbag sensor assembly


B1826/56 Open in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front side squib LH circuit for 2 seconds.

·

A front seat airbag assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly LH

·

Airbag sensor assembly


B1827/56 Short to GND in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front side squib LH circuit for 0.5 seconds.

·

A front seat airbag assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly LH

·

Airbag sensor assembly


B1828/56 Short to B+ in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front side squib LH circuit for 0.5 seconds.

·

A front seat airbag assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

C326339E11
0.615,3.292 3.677,3.49 3.063,0.198 10 false Front Seat Airbag Assembly LH 0.615,3.115 0.969,3.302 0.354,0.188 10 false N11 1.958,1.542 2.375,1.729 0.417,0.188 10 false SFL+ 1.969,2.385 2.385,2.573 0.417,0.188 10 false SFL- 2.469,1.552 2.885,1.74 0.417,0.188 10 false 2 2.458,2.406 2.875,2.594 0.417,0.188 10 false 1 4.51,2.406 4.927,2.594 0.417,0.188 10 false 10 4.521,1.552 4.938,1.74 0.417,0.188 10 false 9 4.771,1.667 5.188,1.854 0.417,0.188 10 false SFL+ 4.781,2.531 5.198,2.719 0.417,0.188 10 false SFL- 4.823,4.177 5.177,4.365 0.354,0.188 10 false N14 4.802,4.375 6.438,4.604 1.635,0.229 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG ASSEMBLY LH
a.
C256394C02
0.521,2.177 0.896,2.417 0.375,0.24 2.115,2.802 1.906,2.708 false 0.813,0.406 1.125,0.604 0.313,0.198 10 false *1 0.979,0.917 1.292,1.115 0.313,0.198 10 false D 1.208,0.917 1.521,1.115 0.313,0.198 10 false C 1.75,0.604 2.063,0.802 0.313,0.198 10 false A 2.063,1.26 2.375,1.458 0.313,0.198 10 false *2 1.542,1.708 1.854,1.906 0.313,0.198 10 false *a 2,1.844 2.313,2.042 0.313,0.198 10 false *3 0.594,2.219 0.906,2.417 0.313,0.198 10 false N11 2.167,2.729 2.479,2.927 0.313,0.198 10 false *4
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag assembly LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output.


HINT:

Codes other than DTC B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.



DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output.

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208251C18
0.625,0.781 0.792,0.948 0.167,0.167 10 false *1 1.24,0.771 1.406,0.938 0.167,0.167 10 false *2 1.719,1.656 1.958,1.844 0.24,0.188 10 false *3 1.896,1.031 2.073,1.229 0.177,0.198 10 false A 1.49,1.271 1.646,1.448 0.156,0.177 10 false B 1.094,1.271 1.281,1.438 0.188,0.167 10 false C 0.865,1.271 1.042,1.438 0.177,0.167 10 false D
*1 Front Seat Airbag Assembly LH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat airbag assembly LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
C202682C02
0.74,2.177 1.104,2.448 0.365,0.271 2.313,3.188 1.875,2.802 true 1.271,3.198 1.646,2.802 true 0.698,0.594 0.948,0.771 0.25,0.177 10 false *1 1.26,0.594 1.51,0.771 0.25,0.177 10 false *2 0.917,1.104 1.167,1.281 0.25,0.177 10 false D 1.125,1.104 1.375,1.281 0.25,0.177 10 false C 1.5,1.104 1.75,1.281 0.25,0.177 10 false B 1.927,0.854 2.177,1.031 0.25,0.177 10 false A 2.156,1.469 2.406,1.646 0.25,0.177 10 false *3 0.802,2.229 1.177,2.448 0.375,0.219 10 false N11 2.604,2.292 2.854,2.469 0.25,0.177 10 false *4 1.042,3.24 1.49,3.417 0.448,0.177 10 false SFL- 2.25,3.229 2.74,3.417 0.49,0.188 10 false SFL+ 1.667,1.875 1.917,2.052 0.25,0.177 10 false *a
*1 Front Seat Airbag Assembly LH
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N11-2 (SFL+) - Body ground Ignition switch ON Below 1 V
N11-1 (SFL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-2 (SFL+) - N11-1 (SFL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-2 (SFL+) - N11-1 (SFL-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-2 (SFL+) - Body ground Always 1 MΩ or higher
N11-1 (SFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C207519C12
0.844,0.813 1.01,0.99 0.167,0.177 10 false *1 2.104,1.646 2.344,1.844 0.24,0.198 10 false *2 1.188,1.25 1.323,1.406 0.135,0.156 10 false C 1.052,1.25 1.188,1.406 0.135,0.156 10 false D 1.698,1.021 1.833,1.177 0.135,0.156 10 false A
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output


HINT:

Codes other than DTC B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.




DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output