Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM3250E _52 Drivetrain _038029 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0194108 AUTOMATIC TRANSMISSION SYSTEM J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "5" (S5 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C311455E33
0.552,1.719 3.458,1.917 2.906,0.198 10 false from IG1 NO. 4 Fuse 3.635,2.229 4.25,2.427 0.615,0.198 10 false SFTU 3.635,2.823 4.25,3.021 0.615,0.198 10 false SFTD 3.885,1.656 4.5,1.854 0.615,0.198 10 false S 5.167,1.646 5.781,1.844 0.615,0.198 10 false S 5.146,2.229 5.76,2.427 0.615,0.198 10 false SFTU 5.146,2.833 5.76,3.031 0.615,0.198 10 false SFTD 2.167,3.427 2.781,3.625 0.615,0.198 10 false I1 2.156,3.594 4.802,3.948 2.646,0.354 10 false Transmission Control Switch (Transmission Floor Shift Assembly) 5.604,3.844 6.219,4.042 0.615,0.198 10 false G90 5.604,4.01 6.104,4.292 0.5,0.281 10 false TCM 2.719,1.646 3.333,1.844 0.615,0.198 10 false IG 2.729,2.229 3.344,2.427 0.615,0.198 10 false E 2.552,1.844 2.865,2.042 0.313,0.198 10 false 4 2.552,2.448 2.865,2.646 0.313,0.198 10 false 2 4.906,3.031 5.219,3.229 0.313,0.198 10 false 23 4.896,2.448 5.208,2.646 0.313,0.198 10 false 22 4.906,1.844 5.219,2.042 0.313,0.198 10 false 15 4.083,1.854 4.396,2.052 0.313,0.198 10 false 5 6.042,2.042 6.5,2.24 0.458,0.198 10 false 12 V 6.042,2.625 6.5,2.823 0.458,0.198 10 false 12 V 4.073,2.458 4.417,2.615 0.344,0.156 10 false 3*1 4.083,3.042 4.375,3.208 0.292,0.167 10 false 1*1 4.073,2.635 4.531,2.833 0.458,0.198 10 false 1*2 4.094,3.208 4.365,3.375 0.271,0.167 10 false 3*2 0.094,4.156 0.885,4.323 0.792,0.167 10 false *1: for LHD 0.094,4.448 0.917,4.615 0.823,0.167 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Powertrain > ECT > Data List
Tester Display
Sports Mode Selection SW
50003 235 155

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Powertrain > ECT > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 235 158,157

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the transmission control switch (transmission floor shift assembly) connector.


b.
C277025C42
0.927,1.75 1.76,1.385 true 2.042,1.771 2.031,1.385 true 2.885,1.771 2.292,1.396 true 0.75,0.448 1.063,0.646 0.313,0.198 10 false *a 0.688,1.802 1.146,2 0.458,0.198 10 false SFTU 2,1.802 2.458,2 0.458,0.198 10 false E 2.771,1.813 3.229,2.01 0.458,0.198 10 false SFTD 0.104,0.104 0.656,0.448 0.552,0.344 10 false *A
*A for LHD
*a Component without harness connected
(Transmission Control Switch)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
3 (SFTU) - 2 (E) Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever not held in "-" 10 kΩ or higher



c.
C277025C43
0.885,1.813 1.76,1.385 true 2.052,1.781 2.031,1.385 true 2.885,1.802 2.292,1.396 true 0.75,0.448 1.063,0.646 0.313,0.198 10 false *a 2.792,1.833 3.25,2.031 0.458,0.198 10 false SFTU 2.01,1.823 2.469,2.021 0.458,0.198 10 false E 0.688,1.844 1.146,2.042 0.458,0.198 10 false SFTD 0.104,0.104 0.656,0.448 0.552,0.344 10 false *A
*A for RHD
*a Component without harness connected
(Transmission Control Switch)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
1 (SFTU) - 2 (E) Shift lever not held in "+" 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C267936C22
0.229,0.979 0.583,1.24 0.354,0.26 0.927,1.896 1.5,1.406 true 0.813,1.854 1.125,2.052 0.313,0.198 10 false E 0.365,1.031 0.677,1.229 0.313,0.198 10 false I1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch (Transmission Floor Shift Assembly))


Disconnect the transmission control switch (transmission floor shift assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)
a.
C212049C12
2.208,0.375 2.615,0.635 0.406,0.26 1.292,2.781 2.333,2.156 true 2.49,2.781 2.396,2.156 true 0.938,2.844 1.615,3.031 0.677,0.188 10 false 23 (SFTD) 2.271,0.417 2.948,0.615 0.677,0.198 10 false G90 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 2.208,2.844 2.885,3.021 0.677,0.177 10 false 22 (SFTU)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G90-22 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
G90-23 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
G90-22 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
G90-23 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C277025C33
0.802,1.802 1.219,1.385 true 1.615,1.781 1.479,1.396 true 1.573,1.833 1.885,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Transmission Control Switch (Transmission Floor Shift Assembly))


Disconnect the transmission control switch (transmission floor shift assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C267936C23
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.354,1.031 0.667,1.229 0.313,0.198 10 false I1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch (Transmission Floor Shift Assembly))


Disconnect the transmission control switch (transmission floor shift assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I1-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I1-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)
a.

Disconnect the I1 transmission control switch (transmission floor shift assembly) connector.


b.

Disconnect the G90 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-5 (S) - G90-15 (S) Always Below 1 Ω
I1-5 (S) - Body ground Always 10 kΩ or higher
G90-15 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR