Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0199793 ECD SYSTEM(w/ DPF) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  


DESCRIPTION

Refer to DTC P200C

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>P200C

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

·

If DTC P20CD is present, refer to the DTC table for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector assembly off, the FIVO output is high for 3 seconds (1 trip detection logic).
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored

HINT:

DTC P200C, P200E, P20CF and/or P2428 will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVO) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVO signal, the ECM judges that the current has been applied to the exhaust fuel addition injector assembly.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVO are inconsistent.

A265674E03
2.667,3.208 3.01,3.385 0.344,0.177 10 ECM 1.229,0.906 1.573,1.125 0.344,0.219 10 CPU 1.417,1.583 1.813,1.74 0.396,0.156 10 FIVO 1.521,2.469 1.771,2.625 0.25,0.156 10 FIV 3.219,1.469 4.25,1.646 1.031,0.177 10 Monitor Circuit 3.188,2.344 4.292,2.521 1.104,0.177 10 Command Circuit 5.458,1.063 7.01,1.74 1.552,0.677 10 to Exhaust Fuel Addition Injector Assembly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CD Ignition switch ON for 3 seconds

WIRING DIAGRAM

A348547E03
3.146,1.042 3.604,1.24 0.458,0.198 10 false C109 3.073,1.229 5.688,1.458 2.615,0.229 10 false Exhaust Fuel Addition Injector Assembly 6.021,0.458 6.479,0.656 0.458,0.198 10 false 6 6.271,0.646 6.813,0.854 0.542,0.208 10 false FIV 5.938,0.656 6.396,0.854 0.458,0.198 10 false G85 6.271,4.229 6.813,4.438 0.542,0.208 10 false MREL 5.948,4.354 6.406,4.552 0.458,0.198 10 false G85 5.979,4.156 6.438,4.354 0.458,0.198 10 false 14 1.854,4.354 2.313,4.552 0.458,0.198 10 false 2K 5.115,2.813 5.573,3.01 0.458,0.198 10 false 2G 1.865,2.823 2.323,3.021 0.458,0.198 10 false 2B 1.865,3.219 2.323,3.417 0.458,0.198 10 false 2J 3.406,4.667 4.469,4.885 1.063,0.219 10 false EFI-MAIN NO. 1 2.479,5.01 4.615,5.24 2.135,0.229 10 false Instrument Panel Junction Block 0.594,5.667 1.365,5.865 0.771,0.198 10 false Battery 0.438,4.865 1.125,5.042 0.688,0.177 10 false FL MAIN 0.688,2.99 1.313,3.208 0.625,0.219 10 false J/B-B 0.698,2.688 0.885,2.885 0.188,0.198 10 false 1 0.969,2.688 1.188,2.896 0.219,0.208 10 false 2 2.281,4.156 3.344,4.375 1.063,0.219 10 false EFI-MAIN NO. 1 2.469,2.979 3.531,3.198 1.063,0.219 10 false EFI-MAIN NO. 2 3.396,3.531 4.458,3.75 1.063,0.219 10 false EFI-MAIN NO. 2 4.365,2.99 5.083,3.229 0.719,0.24 10 false EFI NO. 1 4.76,2.677 4.979,2.885 0.219,0.208 10 false 2 4.51,2.667 4.698,2.865 0.188,0.198 10 false 1 3.042,2.688 3.26,2.896 0.219,0.208 10 false 2 2.896,3.844 3.115,4.052 0.219,0.208 10 false 2 2.646,3.854 2.833,4.052 0.188,0.198 10 false 1 4.49,0.563 4.708,0.771 0.219,0.208 10 false 2 2.792,2.688 2.979,2.885 0.188,0.198 10 false 1 3.104,0.563 3.292,0.76 0.188,0.198 10 false 1 1.906,2.635 2.094,2.833 0.188,0.198 10 false 1 1.896,3.042 2.083,3.24 0.188,0.198 10 false 5 1.906,4.177 2.094,4.375 0.188,0.198 10 false 3 5.156,2.625 5.344,2.823 0.188,0.198 10 false 3 5.146,3.042 5.333,3.24 0.188,0.198 10 false 9 5.156,3.802 5.344,4 0.188,0.198 10 false 7 5.146,4.177 5.333,4.375 0.188,0.198 10 false 8 5.115,3.219 5.573,3.417 0.458,0.198 10 false 2P 5.104,3.99 5.563,4.188 0.458,0.198 10 false 2G 5.115,4.344 5.573,4.542 0.458,0.198 10 false 2P 6.438,5.656 6.979,5.865 0.542,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)

NG

12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)
a.
A204917C08
0.417,1.042 0.813,1.302 0.396,0.26 0.396,0.25 0.615,0.438 0.219,0.188 10 false *a 0.458,1.083 0.823,1.229 0.365,0.146 10 false C109
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


Disconnect the exhaust fuel addition injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C109-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C109-1 - G85-6 (FIV) Always Below 1 Ω
C109-1 - G85-6 (FIV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Remove the instrument panel junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C109-2 - 2G-3 Always Below 1 Ω
C109-2 or 2G-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)
a.

Inspect the instrument panel junction block assembly (EFI-MAIN NO. 2).

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - ECM)

NG

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)
7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - ECM)
a.

Remove the instrument panel junction block connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-8 - G85-14 (MREL) Always Below 1 Ω
2P-8 or G85-14 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the instrument panel junction block connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 2)
a.

Replace the instrument panel junction block assembly.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END