Home › Drivetrain › RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE › INPUT SHAFT
RM3250E _52 Drivetrain _038035 RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE _0200882 INPUT SHAFT A

RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33333 1.INSPECT 3RD GEAR THRUST CLEARANCE

a.
C334003

Using a dial indicator, measure the 3rd gear thrust clearance.

Standard clearance:

0.200 to 0.490 mm (0.0079 to 0.0192 in.)


If the clearance is outside the specification, replace the 3rd gear, thrust washer, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33333 2.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
C325071

Using a dial indicator, measure the 3rd gear radial clearance.

Standard clearance:

0.0150 to 0.065 mm (0.0006 to 0.0025 in.)


If the clearance is outside the specification, replace the 3rd gear, 3rd gear needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33337 3.INSPECT 6TH GEAR SUB-ASSEMBLY THRUST CLEARANCE

a.
C336131

Using a feeler gauge, measure the 6th gear sub-assembly thrust clearance.

Standard clearance:

0.150 to 0.580 mm (0.0059 to 0.0228 in.)


If the clearance is outside the specification, replace the 6th gear sub-assembly, thrust washer, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33337 4.INSPECT 6TH GEAR SUB-ASSEMBLY RADIAL CLEARANCE

a.
C325073

Using a dial indicator, measure the 6th gear sub-assembly radial clearance.

Standard clearance:

0.015 to 0.067 mm (0.0006 to 0.0026 in.)


If the clearance is outside the specification, replace the 6th gear sub-assembly, 6th gear needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33336 5.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C334004

Using a feeler gauge, measure the 5th gear thrust clearance.

Standard clearance:

0.150 to 0.410 mm (0.0060 to 0.0161 in.)


If the clearance is outside the specification, replace the 5th gear, thrust washer, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33336 6.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
C325074

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:

0.013 to 0.054 mm (0.0006 to 0.0021 in.)


If the clearance is outside the specification, replace the 5th gear, thrust washer, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33362A 7.REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

a.
C322582

Using 2 screwdrivers and a hammer, tap off the No. 2 clutch hub setting shaft snap ring.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33364 8.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.

Remove the No. 2 transmission hub sleeve from the No. 2 transmission clutch hub.


Hide 33365 9.REMOVE NO. 1 SYNCHROMESH SHIFTING KEY

a.

Remove the No. 1 synchromesh shifting key from the No. 2 transmission clutch hub.


Hide 33362 10.REMOVE NO. 2 TRANSMISSION CLUTCH HUB

a.
C322583N01
0.521,0.375 0.813,0.375 0.813,0.375 1.01,0.688 true 0.146,0.323 0.604,0.521 0.458,0.198 10 false SST

Using SST and a press, remove the No. 2 transmission clutch hub, No. 3 synchronizer ring set and 3rd gear from the input shaft.

SST
09555-55010  09950-60010  (09951-00410)

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand so that it does not fall.




Hide 33333A 11.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

C322584

a.

Remove the 3rd gear needle roller bearing from the input shaft.


Hide 33429A 12.REMOVE 3RD GEAR SPACER

a.

Remove the 3rd gear spacer from the input shaft.


Hide 33342B 13.REMOVE GEAR THRUST WASHER SHAFT SNAP RING

a.
C322585

Using a snap ring expander, remove the gear thrust washer shaft snap ring from the input shaft.


Hide 33342C 14.REMOVE 3RD GEAR THRUST WASHER

a.

Remove the 3rd gear thrust washer from the input shaft.


Hide 33342A 15.REMOVE GEAR THRUST WASHER STRAIGHT PIN

a.

Remove the gear thrust washer straight pin from the input shaft.


Hide 33337 16.REMOVE 6TH GEAR SUB-ASSEMBLY

a.

Remove the 6th gear sub-assembly from the input shaft.


Hide 33369 17.REMOVE NO. 3 SYNCHRONIZER RING

a.

Remove the No. 3 synchronizer ring from the No. 3 transmission clutch hub.


Hide 33337A 18.REMOVE 6TH GEAR NEEDLE ROLLER BEARING

a.

Remove the 6th gear needle roller bearing from the input shaft.


Hide 33337B 19.REMOVE 6TH GEAR SPACER

a.

Remove the 6th gear spacer from the input shaft.


Hide 33364 20.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.

Remove the No. 2 transmission hub sleeve from the No. 3 transmission clutch hub.


Hide 33365 21.REMOVE NO. 1 SYNCHROMESH SHIFTING KEY

a.

Remove the No. 1 synchromesh shifting key from the No. 3 transmission clutch hub.


Hide 33321D 22.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.
C322586

Using a snap ring expander, remove the clutch hub set shaft snap ring from the input shaft.


Hide 33336 23.REMOVE 5TH GEAR

a.
C322587N01
2.573,0.865 2.781,0.865 false 2.531,2.99 3.021,3.146 3.021,3.146 3.177,2.521 false 2.854,0.792 3.313,0.99 0.458,0.198 10 false SST 2.938,3.188 3.396,3.385 0.458,0.198 10 false SST

Using SST and a press, remove the 5th gear and No. 3 transmission clutch hub from the input shaft.

SST
09527-20011  09950-60010  (09951-00410)

NOTICE:

Support the input shaft so that it does not fall.



Hide 33336A 24.REMOVE 5TH GEAR NEEDLE ROLLER BEARING

a.

Remove the 5th gear needle roller bearing from the input shaft.


Hide 33311A 25.REMOVE FRONT INPUT SHAFT BEARING

a.
C322588

Using a snap ring expander, remove the snap ring from the input shaft.


b.
C323808N01
2.542,1.365 1.885,1.583 1.885,1.583 2.281,1.677 true 1.552,1.49 2.01,1.688 0.458,0.198 10 false SST

Using SST, remove the front input shaft bearing from the input shaft.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04020, 09955-04031, 09957-04010, 09958-04011)
09950-60010  (09951-00180)