Home › Power Source / Network › 5L-E BATTERY / CHARGING › GENERATOR › from 2016.01
RM3250E _57 Power Source / Network _049929 5L-E BATTERY / CHARGING _0240671 GENERATOR A

5L-E BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 29300 1.INSPECT GENERATOR WITH VACUUM PUMP ASSEMBLY

a.

Mount the generator assembly in the vise between aluminum plates.


b.
A220268C01
0,0 0,0 false
V100135

Turn


Insert a screwdriver to hold the generator rotor assembly.


c.

Install the bolt and nut to the outside of the pulley so that the bolt head and nut clamp the pulley, and then position a dial indicator as shown in the illustration.


d.

Turn the pulley and measure the backlash between the generator rotor assembly and vacuum pump shaft.

Maximum backlash:

1.6 mm (0.0630 in.)


If the backlash is more than the maximum, replace the generator rotor assembly and vacuum pump shaft.


Hide 29300 2.REMOVE VACUUM PUMP ASSEMBLY

a.
A220269C02
0.583,0.25 0.667,0.25 0.667,0.25 1.479,0.688 true 0.396,0.156 0.708,0.313 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks as shown in the illustration.


b.

Remove the 4 bolts and vacuum pump assembly.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A220270

Remove the nut and terminal insulator.


b.

Remove the bolt, 3 nuts, rectifier plate and generator rear end cover.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.

Remove the brush holder cover.


b.
A226311

Remove the 2 screws and generator brush holder assembly.


c.

Remove the plate seal.


Hide 27700A 5.REMOVE GENERATOR REGULATOR ASSEMBLY

a.
A226312

Remove the 3 screws and generator regulator assembly.


Hide 27357 6.REMOVE GENERATOR HOLDER WITH RECTIFIER

a.
A220272

Remove the 4 screws and generator holder with rectifier.


b.

Remove the 4 rubber insulators.


Hide 27359 7.REMOVE GENERATOR RECTIFIER END FRAME

a.
A220273C02
2.729,0.781 2.917,1.167 2.917,1.167 3,1.167 true 3.073,1.073 3.302,1.24 0.229,0.167 10 false *1
*1 Cord Clip


Remove the 4 nuts and cord clip.


b.
A220274C02
1.875,0.875 2.354,1.615 2.354,1.615 2.438,1.615 true 0.5,0.281 0.813,0.438 0.313,0.156 10 false *a 2.479,1.531 2.938,1.729 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator rectifier end frame.

SST
09286-46011  


c.

Remove the washer from the generator rotor assembly.


Hide 27330 8.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A220275N01
1.083,0.417 1.167,0.417 1.167,0.417 1.698,0.927 true 1.844,0.594 2.25,0.25 2.25,0.25 2.313,0.25 true 2.396,0.146 2.854,0.344 0.458,0.198 10 false SST 0.75,0.333 1.208,0.531 0.458,0.198 10 false SST

Using SST and a press, press out the generator rotor assembly.

SST
09950-60010  (09951-00180)
09950-70010  (09951-07100)