Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made) › from 2016.01
RM3250E _52 Drivetrain _038038 DRIVE SHAFT / PROPELLER SHAFT _0242560 FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.REMOVE SLIDING SHAFT BOOT

a.
C346193C01
2.667,1.5 2.75,1 2.75,1 2.917,1 true 1.833,1.5 1.417,0.833 1.417,0.833 1.25,0.833 true 1.833,1.667 1.417,2.25 1.417,2.25 1.25,2.25 true 2.667,1.667 2.833,2.167 2.833,2.167 3,2.167 true 2.5,1.5 2.667,0.667 2.667,0.667 2.833,0.667 true 1.979,1.417 2.146,0.25 2.146,0.25 2.313,0.25 true 2.25,1.417 2.5,0.417 2.5,0.417 2.667,0.417 true 2.417,2.333 2.417,2.25 2.417,2.25 1.833,2.25 true 3,0.917 3.313,1.115 0.313,0.198 10 false *b 1.021,0.75 1.333,0.948 0.313,0.198 10 false *b 1.021,2.167 1.333,2.365 0.313,0.198 10 false *a 3.083,2.083 3.333,2.365 0.25,0.281 10 false *a 2.917,0.583 3.229,0.781 0.313,0.198 10 false *1 2.354,0.167 2.667,0.365 0.313,0.198 10 false *1 2.771,0.333 3.083,0.531 0.313,0.198 10 false *2 1.583,2.167 1.833,2.448 0.25,0.281 10 false *c
*1 Propeller Shaft Boot Clamp
*2 Sliding Shaft Boot
*a Matchmark of Front Propeller Shaft Assembly and Sleeve Yoke
*b Matchmark of Pinching Portion of Propeller Shaft Boot Clamp
*c Pinching Portion


Place matchmarks on the front propeller shaft assembly and sleeve yoke.


b.

Apply matchmarks at the pinching portions of the propeller shaft boot clamps of the front propeller shaft assembly and sleeve yoke.

HINT:
·

Make sure to place matchmarks to clearly identify the location of the pinching portions of the propeller shaft boot clamps.

If the pinching portions are installed at different locations than where they were located before disassembly, the rotational balance of the front propeller shaft assembly cannot be ensured, which may result in vibrations and noise.

·

Make sure that the matchmarks are different enough so that they cannot be confused with each other.

·

The location of the pinching portions may differ from the location shown in the illustration, so make sure to confirm and properly place matchmarks according to the vehicle.




c.

Using a side cutter or pliers, disconnect the 2 propeller shaft boot clamps.


d.

Disconnect the 2 propeller shaft boot clamps.


e.

Remove the sleeve yoke, and then remove the sliding shaft boot and 2 propeller shaft boot clamps.


Hide 2.REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for both universal joint spiders.


a.
F052432C08
1.604,0.802 1.604,0.375 1.604,0.375 2.146,0.375 false 1.823,0.865 1.823,0.375 false 2.229,0.281 2.521,0.458 0.292,0.177 10 false *a
*a Matchmark


Place matchmarks on the flange yoke and front propeller shaft assembly.


b.
F052433

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


c.

Using needle nose pliers, remove the 4 snap rings from the grooves.


d.
C317895C01
0.833,1.167 1.167,1.167 true 2.625,1.25 3.063,1.25 true 1.708,0.635 2.021,0.833 0.313,0.198 10 false *a 0.625,0.656 0.938,0.854 0.313,0.198 10 false *b 0.5,1.083 0.833,1.281 0.333,0.198 10 true SST 3.146,1.167 3.302,1.396 0.156,0.229 10 true A
*a Turn
*b Hold


Using SST, push out the spider bearing from the front propeller shaft assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



e.
C237736C17
2.167,0.677 2.677,0.677 true 2.729,0.573 2.979,0.76 0.25,0.188 10 false *a
*a Hammering Point


Tap off the front propeller shaft assembly to remove the spider bearing.

NOTICE:

Do not tap the shaft.


HINT:

Remove the spider bearing on the opposite side using the same procedure.



f.

Remove the flange yoke from the front propeller shaft assembly.


g.
C307746C01
2.125,1.146 2.5,1.146 true 0.573,1.188 0.948,1.188 true 1.656,0.604 1.969,0.802 0.313,0.198 10 false *a 0.438,0.177 0.781,0.385 0.344,0.208 10 false *b 1.948,1.083 2.156,1.313 0.208,0.229 10 false A 0.26,1.115 0.656,1.313 0.396,0.198 10 false SST
*a Turn
*b Hold


Install the 2 removed spider bearing outer races to the spider.


h.

Using SST, push out the spider bearing from the flange yoke.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



i.
C237737C17
2.521,0.521 3,0.521 true 3.042,0.417 3.24,0.594 0.198,0.177 10 false *a
*a Hammering Point


Tap off the spider bearing with a hammer.

HINT:

Remove the spider bearing on the opposite side using the same procedure.



j.

Remove the spider.