Home › Engine / Hybrid System › 5L-E FUEL › FUEL INJECTION NOZZLE › from 2016.01
RM3250E _51 Engine / Hybrid System _049912 5L-E FUEL _0242564 FUEL INJECTION NOZZLE G

5L-E FUEL  FUEL INJECTION NOZZLE  INSPECTION  


PROCEDURE

Hide 23600 1.INSPECT NOZZLE HOLDER AND NOZZLE SET

a.

Pressure test:

i.
A370266

Install the nozzle holder to an injection nozzle hand tester and bleed air from the union nut connection.

NOTICE:

Do not place your finger on the nozzle injection hole.



ii.
A370267

Pump the injection nozzle hand tester handle a few times as fast as possible to discharge the carbon from the nozzle injection hole.


iii.

Pump the injection nozzle hand tester handle slowly and observe the pressure gauge.


iv.

Read the pressure gauge just as the injection pressure begins to drop.

Standard pressure:

16180 to 16770 kPa (165.0 to 171.0 kgf/cm2, 2346 to 2432 psi)


HINT:
·

It can be concluded that the nozzle is operating properly when a swishing sound is heard.

·

If the pressure is not within the standard, disassemble the nozzle holder and replace only the adjusting shim on the top of the nozzle holder pressure spring. Varying the adjusting shim thickness by 0.005 mm (0.000197 in.) changes the injection pressure by approximately 94.6 kPa (1.0 kgf/cm2, 13.7 psi).



Standard Adjusting Shim Thickness
Specified Condition
0.900 mm (0.0354 in.) 1.300 mm (0.0512 in.) 1.700 mm (0.0669 in.)
0.950 mm (0.0374 in.) 1.350 mm (0.0531 in.) 1.750 mm (0.0689 in.)
1.000 mm (0.0394 in.) 1.400 mm (0.0551 in.) 1.800 mm (0.0709 in.)
1.050 mm (0.0413 in.) 1.450 mm (0.0571 in.) 1.850 mm (0.0728 in.)
1.100 mm (0.0433 in.) 1.500 mm (0.0591 in.) 1.900 mm (0.0748 in.)
1.150 mm (0.0453 in.) 1.550 mm (0.0610 in.) 1.950 mm (0.0768 in.)
1.200 mm (0.0472 in.) 1.600 mm (0.0630 in.) -
1.250 mm (0.0492 in.) 1.650 mm (0.0650 in.) -



b.
A370268C01
2.031,1.313 2.344,1.469 0.313,0.156 10 false *a 2.865,1.313 3.177,1.469 0.313,0.156 10 false *b
*a No Good
*b Good


Leakage test:

i.

While maintaining pressure at approximately 981 to 1961 kPa (10.0 to 20.0 kgf/cm2, 142 to 284 psi) below the injection pressure (adjust using the injection nozzle hand tester handle), check that there is no dripping from the nozzle injection hole or around the retaining nut for 10 seconds.

If the nozzle drips within 10 seconds, replace or clean and overhaul the nozzle assembly.



c.
A370269C01
1.281,0.615 1.594,0.771 0.313,0.156 10 false *a 0.594,0.625 0.906,0.781 0.313,0.156 10 false *b 1.948,0.615 2.26,0.771 0.313,0.156 10 false *a 2.635,0.615 2.948,0.771 0.313,0.156 10 false *a
*a No Good
*b Good


Spray pattern test:

i.

The injection nozzle should shudder at a certain pumping speed between 30 and 60 times per minute.


ii.

Check the spray pattern during shuddering.

If the spray pattern is not correct during shuddering, replace or clean the nozzle.



Hide 23620 2.CLEAN NOZZLE ASSEMBLY

a.
A370270C01
1.51,0.167 1.719,0.167 1.719,0.167 1.813,0.604 true 1.323,0.052 1.635,0.208 0.313,0.156 10 false *a
*a Wooden Stick


Using a wooden stick and brass brush, clean the nozzle.

NOTICE:

Do not touch the nozzle contact surface with your fingers.


i.

Using a wooden stick, remove the carbon adhering to the nozzle needle tip.


ii.
A370271

Using a brass brush, remove the carbon from the exterior of the nozzle body (except lapped surface).



Hide 23620 3.INSPECT NOZZLE ASSEMBLY

a.

Wash the nozzle in clean diesel fuel.

NOTICE:

Do not touch the nozzle contact surfaces with your fingers.



b.
A370272

Perform the following test several times, rotating the needle slightly each time.

i.

Tilt the nozzle body approximately 60° and pull the needle out approximately one third of its length.


ii.

Check that the needle falls into the body vent smoothly by its own weight when released. If the needle does not fall smoothly, replace the nozzle assembly.