Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184914 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the except driver door lock position switch system.

WIRING DIAGRAM

B406562E12
5.885,0.875 6.5,1.073 0.615,0.198 10 false PRG3 5.896,1.313 6.51,1.51 0.615,0.198 10 false RDA3 5.885,3.792 6.5,3.99 0.615,0.198 10 false PRG 5.875,3.313 6.49,3.51 0.615,0.198 10 false RDA 5.865,4.323 6.479,4.521 0.615,0.198 10 false LSWP 5.688,3.667 6.302,3.865 0.615,0.198 10 false 9 5.635,3.188 6.25,3.385 0.615,0.198 10 false 16 5.583,0.677 6.198,0.875 0.615,0.198 10 false 36 5.563,1.135 6.177,1.333 0.615,0.198 10 false 13 1.656,0.292 2.271,0.49 0.615,0.198 10 false LSSR 0.75,0.313 1.365,0.51 0.615,0.198 10 false E 1.677,2.052 2.292,2.25 0.615,0.198 10 false LSSR 0.74,2.063 1.354,2.26 0.615,0.198 10 false E 1.688,3.771 2.302,3.969 0.615,0.198 10 false LSSR 0.76,3.781 1.375,3.979 0.615,0.198 10 false E 2.156,0.292 2.771,0.49 0.615,0.198 10 false 7*1, 8*2 0.115,0.302 0.729,0.5 0.615,0.198 10 false 8*1, 7*2 2.167,2.073 7.156,2.333 4.99,0.26 10 false 6*5 0.406,2.063 7.156,2.323 6.75,0.26 10 false 9*5 0.375,3.781 7.156,4.052 6.781,0.271 10 false 9*5 2.188,3.771 7.156,4.01 4.969,0.24 10 false 6*5 5.552,1.948 7.104,2.479 1.552,0.531 10 false Certification ECU (Smart Key ECU Assembly) 5.833,4.969 6.448,5.167 0.615,0.198 10 false G27 5.833,5.156 7.031,5.333 1.198,0.177 10 false Body ECU 0.438,0.854 1.49,1.063 1.052,0.208 10 false J1*1, K1*2 0.438,1.042 2.115,1.479 1.677,0.438 10 false Front Door Lock Assembly (for Front Passenger Door) 0.438,2.583 1.052,2.781 0.615,0.198 10 false L1 0.427,2.75 2.531,3.115 2.104,0.365 10 false Rear Door Lock Assembly RH*3 0.458,4.313 1.073,4.51 0.615,0.198 10 false M1 0.458,4.49 2.594,4.854 2.135,0.365 10 false Rear Door Lock Assembly LH*3 5.875,0.313 6.49,0.51 0.615,0.198 10 false LSWP 5.688,4.375 6.302,4.573 0.615,0.198 10 false 2 5.531,1.313 6.146,1.51 0.615,0.198 10 false G70 5.542,0.875 6.156,1.073 0.615,0.198 10 false G70 5.542,0.427 6.156,0.625 0.615,0.198 10 false G69 5.625,0.208 6.24,0.406 0.615,0.198 10 false 9 0.26,4.896 1.313,5.104 1.052,0.208 10 false *1: for LHD 0.26,5.167 1.313,5.375 1.052,0.208 10 false *2: for RHD 0.271,5.448 1.594,5.698 1.323,0.25 10 false *3: for Double Cab 2.167,1.917 7.156,2.177 4.99,0.26 10 false 9*4 0.333,1.917 7.083,2.177 6.75,0.26 10 false 10*4 2.188,3.615 7.156,3.854 4.969,0.24 10 false 5*4 0.375,3.625 7.156,3.896 6.781,0.271 10 false 6*4 1.979,4.896 7.156,5.135 5.177,0.24 10 false *4: w/ Double Locking 1.979,5.156 7.156,5.396 5.177,0.24 10 false *5: w/o Double Locking

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window master switch is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT DOOR LOCK ASSEMBLY (LOCK POSITION SWITCH)

NG

2.INSPECT DOOR LOCK ASSEMBLY (LOCK POSITION SWITCH)

*: for Double Cab


a.

Remove the front door lock assembly (for Front Passenger Door) (lock position switch).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Remove the rear door lock assembly RH/LH (lock position switch)*.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>REMOVAL


c.

Inspect the front door lock assembly (for Front Passenger Door) (lock position switch).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION


d.

Inspect the rear door lock actuator assembly RH/LH (lock position switch)*.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (LOCK POSITION SWITCH CIRCUIT)

NG

REPLACE TROUBLE PARTS (DOOR LOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (LOCK POSITION SWITCH CIRCUIT)

*1: for Double Cab

*2: for LHD

*3: for RHD


a.

Disconnect the G27 body ECU connector.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the J1*2 or K1*3 front door lock assembly (for Front Passenger Door) connector.


d.

Disconnect the L1 rear door lock assembly RH connector*1.


e.

Disconnect the M1 rear door lock assembly LH connectors*1.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G27-2 (LSWP) - G69-9 (LSWP) Always Below 1 Ω
G27-2 (LSWP) - J1-7 (LSSR) Always Below 1 Ω
G27-2 (LSWP) - L1-6 (LSSR)*1 Always Below 1 Ω
G27-2 (LSWP) - M1-6 (LSSR)*1 Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
L1-9 (E) - Body ground*1 Always Below 1 Ω
M1-9 (E) - Body ground*1 Always Below 1 Ω
G27-2 (LSWP) or G69-9 (LSWP) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or J1-7 (LSSR) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or L1-6 (LSSR) - Body ground*1 Always 10 kΩ or higher
G27-2 (LSWP) or M1-6 (LSSR) - Body ground*1 Always 10 kΩ or higher

for RHD (w/ Double Locking)
Tester Connection Condition Specified Condition
G27-2 (LSWP) - G69-9 (LSWP) Always Below 1 Ω
G27-2 (LSWP) - K1-8 (LSSR) Always Below 1 Ω
G27-2 (LSWP) - L1-9 (LSSR)*1 Always Below 1 Ω
G27-2 (LSWP) - M1-5 (LSSR)*1 Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
L1-10 (E) - Body ground*1 Always Below 1 Ω
M1-6 (E) - Body ground*1 Always Below 1 Ω
G27-2 (LSWP) or G69-9 (LSWP) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or K1-8 (LSSR) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or L1-9 (LSSR) - Body ground*1 Always 10 kΩ or higher
G27-2 (LSWP) or M1-5 (LSSR) - Body ground*1 Always 10 kΩ or higher

for RHD (w/o Double Locking)
Tester Connection Condition Specified Condition
G27-2 (LSWP) - G69-9 (LSWP) Always Below 1 Ω
G27-2 (LSWP) - K1-8 (LSSR) Always Below 1 Ω
G27-2 (LSWP) - L1-6 (LSSR)*1 Always Below 1 Ω
G27-2 (LSWP) - M1-6 (LSSR)*1 Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
L1-9 (E) - Body ground*1 Always Below 1 Ω
M1-9 (E) - Body ground*1 Always Below 1 Ω
G27-2 (LSWP) or G69-9 (LSWP) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or K1-8 (LSSR) - Body ground Always 10 kΩ or higher
G27-2 (LSWP) or L1-6 (LSSR) - Body ground*1 Always 10 kΩ or higher
G27-2 (LSWP) or M1-6 (LSSR) - Body ground*1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the entry lock/unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION HISTORY LIST

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly), body ECU and front door lock assembly (for Front Passenger Door) before performing the inspection.


OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

5.REPLACE BODY ECU
5.REPLACE BODY ECU

Result:
Proceed to
NEXT



NEXT

6.CHECK ENTRY DOOR LOCK OPERATION
6.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the entry lock/unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION HISTORY LIST

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (BODY ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)