Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184917 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


·

The theft deterrent system can be set/canceled by locking/unlocking the doors using the following operation:

·

Entry lock operation

·

Wireless lock operation

HINT:
w/ Entry and Start System w/o Entry and Start System
Entry lock operation ○ -
Wireless lock operation ○ ○
Key linked lock operation ○ ○

·

○: Available

·

-: Not available




·

In the armed state, the alarm function will be activated if one of the following conditions is met:

·

Any of the doors are unlocked.

·

Any of the doors, the engine hood or the back door is opened.

·

The intrusion sensor (theft warning ultrasonic sensor) detects movement inside the cabin.*


*: w/ Intrusion Sensor


·

In the alarm sounding state, the system blinks the turn signal lights. At the same time, the system sounds the vehicle horns and security horn assembly*1 or theft warning siren assembly*2 to deter break-in and theft as well as to warn people around the vehicle.

*1: w/ Security Horn Assembly

*2: w/ Theft Warning Siren Assembly


·

The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state:

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 27.5 seconds


Alarm Methods and Time

*1: w/ Security Horn Assembly

*2: w/ Theft Warning Siren Assembly

Alarm Method Hazard Warning Lights Blinking
Vehicle Horn Sounding
(approximately 0.4-second cycles)
Security Horn Assembly*1 Sounding
(approximately 0.4-second cycles)
Theft Warning Siren Assembly*2 Sounding
Alarm Time Approximately 27.5 seconds



FUNCTION OF MAIN COMPONENTS


Component Function
Theft warning indicator light assembly (security indicator light) Informs driver of theft deterrent system status.
Security horn assembly*3 Sounds when attempted break-in or theft is detected.
Theft Warning Siren Assembly*4 Sounds when attempted break-in or theft is detected.
Hazard warning lights Blink when attempted break-in or theft is detected.
Vehicle horns Sounds when attempted break-in or theft is detected.
Door courtesy light switches Detects door status (open or closed).
Door unlock detection switch Detects door status (locked or unlocked).
Security courtesy switch Detects engine hood status (open or closed).
Intrusion sensor (theft warning ultrasonic sensor)*5 Sends a signal to the body ECU to sound the alarm when detecting an intrusion.
Intrusion sensor cancel switch*5 Sends a signal to the body ECU to cancel the intrusion sensor (theft warning ultrasonic sensor).
Certification ECU (smart key ECU assembly)*1
·

Receives wireless door lock/unlock signal.

·

Receives entry door lock/unlock signal.


Body ECU*2 Receives wireless door lock/unlock signal.
Engine hood courtesy switch (hood lock assembly) Detects engine hood status (open or closed).
Combination meter assembly Receives door status (open or closed) signal.

*1: w/ Entry and Start System

*2: w/o Entry and Start System

*3: w/ Security Horn Assembly

*4: w/ Theft Warning Siren Assembly

*5: w/ Intrusion Sensor



ACTIVE ARMING MODE


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

HINT:

The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH* and rear door RH*.

*: except Single Cab



B214494E13
1.688,1.521 3.146,1.76 1.458,0.24 10 Disarmed State (1)*1 2.302,3.188 4.021,3.396 1.719,0.208 10 Arming Preparation State 2.729,4.583 3.573,4.729 0.844,0.146 10 Armed State 2.406,5.99 3.99,6.24 1.583,0.25 10 Alarm Sounding State 0.24,6.979 3.438,7.198 3.198,0.219 10 *1: Disarmed state 1 is the normal disarmed state 0.24,7.313 5.792,7.583 5.552,0.271 10 *2: Disarmed state 2 is set from either the disarmed state 1 or arming preparation state 1.052,2.531 1.927,2.781 0.875,0.25 10 Condition [3] 3.771,4 4.719,4.26 0.948,0.26 10 Condition [2] 2.948,2.531 3.906,2.781 0.958,0.25 10 Condition [1] 3.833,5.365 4.823,5.677 0.99,0.313 10 Condition [4] 2.469,5.365 3.375,5.635 0.906,0.271 10 Condition [6] 0.563,4.469 1.448,4.708 0.885,0.24 10 Condition [5] 0.563,5.865 1.469,6.135 0.906,0.271 10 Condition [5] 4.99,1.521 6.438,1.771 1.448,0.25 10 Disarmed State (2)*2 1.083,0.885 2.198,1.146 1.115,0.26 10 Disarmed State 3.573,1.25 4.469,1.479 0.896,0.229 10 Condition [9] 3.573,1.906 4.479,2.135 0.906,0.229 10 Condition [8] 4.51,2.531 5.479,2.802 0.969,0.271 10 Condition [7] 4.958,3.469 5.948,3.74 0.99,0.271 10 Condition [10]

w/ Entry and Start System
Condition Item

*1: w/ Door Control Battery

*2: w/ Intrusion Sensor

Condition [1] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood closed, all doors are locked by wireless operation, the entry and start system or key linked power door lock operation.


Condition [2]

Allow approximately 30 seconds to elapse.


Condition [3]
·

All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).

·

The battery is reconnected.*1


Condition [4]
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*2

·

Any door is opened when all doors are closed.

·

When 5 seconds or more have elapsed after the engine switch is pressed, the power source mode is changed from off to on (IG) without pressing the engine switch.

·

The engine hood is open.

·

The power source mode is on (IG).

·

The battery is reconnected with the engine hood open, any door open or any door unlocked.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.*2


Condition [5]
·

The engine switch is turned on (IG) and the engine is running for more than 2 seconds.

·

All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

·

The engine switch is turned on (ACC) or on (IG) within 5 seconds after the engine switch was pushed.


Condition [6]

After approximately 27.5 seconds, alarm stops and system returns to armed state.


Condition [7]

The engine hood is closed when the engine hood is opened.


Condition [8]
·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).

·

All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation.

·

The battery is reconnected.*1


Condition [9] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the engine hood opened, all doors are locked by wireless operation, the entry and start system or key linked power door lock operation.


Condition [10]

The engine hood is opened.



w/o Entry and Start System
Condition Item

*1: w/ Door Control Battery

*2: w/ Intrusion Sensor

Condition [1] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors and the engine hood closed, all doors are locked by wireless operation or key linked power door lock operation.*1


Condition [2]

Allow approximately 30 seconds to elapse.


Condition [3]
·

All doors are unlocked by wireless operation or key linked power door lock operation.

·

Any door is opened.

·

Key is in the key cylinder.

·

The ignition switch is turned to ON.

·

The battery is reconnected.*1


Condition [4]
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*2

·

Any door is opened when all doors are closed.

·

The ignition switch is turned to ON when the key is not in the key cylinder.

·

The engine hood is open.

·

Any door is opened

·

The battery is reconnected with the engine hood open, any door open or any door unlocked.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.*2


Condition [5]
·

The ignition switch is turned to ON and the engine is running for more than 2 seconds.

·

All doors are unlocked by wireless operation or key linked power door lock operation.


Condition [6]

After approximately 27.5 seconds, alarm stops and system returns to armed state.


Condition [7]

The engine hood is closed when the engine hood is opened.


Condition [8]
·

Any door is opened.

·

Key is in the key cylinder.

·

The ignition switch is turned to ON.

·

All doors are unlocked by wireless operation or key linked power door lock operation.

·

The battery is reconnected.*1


Condition [9] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors closed, and the engine hood opened, all doors are locked by wireless operation or key linked power door lock operation.


Condition [10]

The engine hood is opened.





SECURITY INDICATOR LIGHT OUTPUT


HINT:

w/ Immobiliser System:

When the immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state, due to output signals from the immobiliser system.


a.

According to the state of the theft deterrent system, the certification ECU (smart key ECU assembly)*1 or body ECU*2 outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the certification ECU (smart key ECU assembly)*1 or body ECU*2.

*1: w/ Entry and Start System

*2: w/o Entry and Start System


Output
State of Theft Deterrent System Theft Warning Indicator Light Assembly (Security Indicator Light)
Output Signal from certification ECU (smart key ECU assembly)*1 or body ECU*2 Actual Lighting Condition
Disarmed state (1), (2) OFF OFF (Immobiliser system*3 unset)
BLINKING (Immobiliser system*3 set)
Arming preparation state ON ON
Armed state BLINKING BLINKING
Alarm sounding state ON ON

*1: w/ Entry and Start System

*2: w/o Entry and Start System

*3: w/ Immobiliser System


Blinking Cycle
Time Security Indicator Light
0.125 seconds ON
1.875 seconds OFF



REMOTE ALARM FUNCTION (w/ Alarm Switch)


a.

Remote alarm function makes it possible to voluntarily set off the remote alarm by pressing the alarm switch on the electrical key transmitter sub-assembly.

i.

Conditions that cause remote alarm function to set off the remote alarm:

The alarm switch on the electrical key transmitter sub-assembly is pressed under the following conditions:

·

The ignition switch is off.

·

The theft deterrent system is not in the alarm sounding state.



ii.

Conditions that cause the remote alarm function to shut off the alarm:

Any of the following conditions is met during remote alarm function operation:

·

The ignition switch is to ON.

·

The alarm switch is pressed again.

·

Any of the switches on the electrical key transmitter sub-assembly (lock/unlock) is pressed.

·

The alarm ends (approximately 27.5 seconds have elapsed).

·

The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system controls the alarm rather than the remote alarm function. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.





INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (w/ Intrusion Sensor)


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.


a.

An intrusion sensor (theft warning ultrasonic sensor) is provided in the map light assembly located in the front of the vehicle interior.


b.

Body ECU activates the intrusion sensor (theft warning ultrasonic sensor) when the system changes from the disarmed state to the armed preparation state. If an intrusion detection signal is input from the intrusion sensor (theft warning ultrasonic sensor) during the armed state, the body ECU changes to the alarm sounding state in order to output an alarm.


c.

When the system is in the disarmed state, the function of the intrusion sensor (theft warning ultrasonic sensor) can be disabled by pressing the intrusion sensor cancel switch.


d.

The intrusion sensor (theft warning ultrasonic sensor) may erroneously detect intrusion in the following states:

·

Persons or pets are in the vehicle.

·

The vehicle is parked in a place where extreme vibrations or noises occur, such as in a parking garage.

·

Ice or snow is removed from the vehicle, causing the vehicle to receive repeated impacts or vibrations.

·

The wind or something similar causes an externally mounted reflectively coated windshield cover to move.

·

The intrusion sensor (theft warning ultrasonic sensor) may react to a hanger or other objects hanging in the cabin when they drop or swing.

·

The system changes to the armed state even when any of the windows is open. The intrusion sensor (theft warning ultrasonic sensor) may react to objects moving outside the vehicle when any of the windows is open.

·

The vehicle is inside an automatic or high-pressure car wash.

·

The vehicle experiences impacts, such as hail, lightning strikes and other kinds of repeated impacts or vibrations.




THEFT WARNING SIREN ASSEMBLY (w/ Theft Warning Siren Assembly)


a.

The theft warning siren assembly has an internal battery. If power to the theft warning siren assembly is interrupted or the communication line is open, the theft warning siren assembly detects it and sounds the alarm using the internal battery.


b.

The theft warning siren assembly has the following alarm controls: normal alarm control and open circuit alarm control. Under normal alarm control, the alarm sounds based on instructions from the body ECU whereas under open circuit alarm control, the theft warning siren assembly judges current security conditions and sounds the alarm by itself.

i.

Normal alarm control

The theft warning siren assembly sounds when the theft deterrent system is in the alarm sounding state and does not sound when the system is not in the alarm sounding state.

HINT:

If communication interruption between the theft warning siren assembly and body ECU continues for 70 seconds or more while the theft deterrent system is in the alarm sounding state, the theft warning siren assembly stops sounding.



ii.
B315877E02
0.083,0.083 2.979,0.458 2.896,0.375 10 false Conditions of theft warning siren assembly 1.292,0.875 2.26,1.125 0.969,0.25 10 false Disarmed State 1.385,2.219 2.323,2.469 0.938,0.25 10 false Armed State 0.958,1.667 1.104,1.813 0.146,0.146 10 false *1 2.448,1.677 2.729,1.854 0.281,0.177 10 false *2 0.458,3.177 2.99,3.531 2.531,0.354 10 false *1: Theft deterrent system changes to the armed state. 0.479,3.938 3.031,4.323 2.552,0.385 10 false *2: Theft deterrent system changes to the disarmed state.

Open circuit alarm control

The theft warning siren assembly changes between the disarmed state and armed state in accordance with the theft deterrent system changes between the disarmed state and armed state. If the power source, ground or communication line is open while the theft warning siren assembly is in the armed state, the theft warning siren assembly sounds.

During the open circuit alarm sounding state, the theft warning siren assembly sounds intermittently for 27.5 seconds and then stops for 5 seconds. This pattern repeats a maximum of 9 times.

The intermittent sounding will stop when either condition is met:

1. The theft warning siren assembly changes to the disarmed state.

2. The open circuit is returned to normal.

B267215E03
0.063,0.083 3.781,0.302 3.719,0.219 10 (a) Intermittent sound pattern repeats a maximum of 9 times 0.229,0.427 2.74,0.635 2.51,0.208 10 Theft warning siren is in the armed state 1.854,1.25 2.76,1.49 0.906,0.24 10 Circuit is open 1.729,1.76 2.75,2 1.021,0.24 10 Circuit is normal 1.031,2.063 3.469,2.302 2.438,0.24 10 Theft warning siren sounds 0.729,2.573 2.802,2.823 2.073,0.25 10 Theft warning siren sounds stop 1.854,8.031 2.76,8.271 0.906,0.24 10 Circuit is open 1.729,8.552 2.75,8.781 1.021,0.229 10 Circuit is normal 1.031,8.854 3.281,9.083 2.25,0.229 10 Theft warning siren sounds 0.729,9.365 2.76,9.615 2.031,0.25 10 Theft warning siren sounds stop 0.063,0.917 2.729,1.146 2.667,0.229 10 Theft warning siren is in the disarmed state 0.26,7.219 2.75,7.438 2.49,0.219 10 Theft warning siren is in the armed state 0.063,7.708 2.729,7.938 2.667,0.229 10 Theft warning siren is in the disarmed state 1.854,4.719 2.76,4.927 0.906,0.208 10 Circuit is open 1.729,5.229 2.75,5.469 1.021,0.24 10 Circuit is normal 1.031,5.531 3.375,5.75 2.344,0.219 10 Theft warning siren sounds 0.729,6.052 2.75,6.302 2.021,0.25 10 Theft warning siren sounds stop 0.26,3.896 2.76,4.146 2.5,0.25 10 Theft warning siren is in the armed state 0.063,4.396 2.74,4.604 2.677,0.208 10 Theft warning siren is in the disarmed state 4.74,0.083 5.833,0.281 1.094,0.198 10 T1: 27.5 seconds 3.344,2.417 3.531,2.563 0.188,0.146 10 T1 3.531,2.885 3.719,3.031 0.188,0.146 10 T2 3.333,5.885 3.521,6.031 0.188,0.146 10 T1 3.333,9.188 3.521,9.333 0.188,0.146 10 T1 3.531,9.656 3.719,9.802 0.188,0.146 10 T2 6.052,0.083 6.948,0.344 0.896,0.26 10 T2: 5 seconds 0.063,3.229 2.604,3.458 2.542,0.229 10 (b) The open circuit is returned to normal 0.063,3.5 3.917,3.729 3.854,0.229 10 (1) The open circuit is returned to normal within 27.5 seconds 0.063,6.792 4.792,7.021 4.729,0.229 10 (2) The open circuit is returned to normal after 27.5 seconds or more elapsed




CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (w/ Intrusion Sensor)


a.

Check that the engine hood is closed.


b.

Check the intrusion sensor (theft warning ultrasonic sensor) operation.

i.

Turn the ignition switch off.


ii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).


iii.

Wait 30 seconds after locking all the doors using the wireless door lock or entry door lock function and check that the security indicator light blinks (armed state). Then, check that the theft deterrent system alarm operates due to movement inside the vehicle.

HINT:

If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.



iv.

Perform an unlock operation using the wireless or entry operation to stop the alarm.




CHECK INTRUSION SENSOR OFF SWITCH (w/ Intrusion Sensor)


a.

Check that the engine hood is closed.


b.

Check the intrusion sensor OFF switch operation.

i.

Turn the ignition switch off.


ii.

Press the intrusion sensor OFF switch.


iii.

Lock all the doors using the wireless door lock or entry door lock function and check that the security indicator light illuminates (armed preparation state).


iv.

Approximately 30 seconds after locking all the doors via wireless operation or smart operation, check that the security indicator light changes to blinking (armed state) and the auto alarm does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the smart exterior area.

HINT:

Even if the intrusion sensor (theft warning ultrasonic sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.